欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    AASHTO R 66-2015 Standard Practice for Sampling Asphalt Materials.pdf

    • 资源ID:418018       资源大小:279.17KB        全文页数:8页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    AASHTO R 66-2015 Standard Practice for Sampling Asphalt Materials.pdf

    1、Standard Practice for Sampling Asphalt Materials AASHTO Designation: R 66-151American Association of State Highway and Transportation Officials 444 North Capitol Street N.W., Suite 249 Washington, D.C. 20001 TS-2a R 66-1 AASHTO Standard Practice for Sampling Asphalt Materials AASHTO Designation: R 6

    2、6-1511. SCOPE 1.1. This standard applies to sampling asphalt materials at production facilities, at storage facilities, or at the point of delivery. Samples may be taken from tanks, stockpiles, vehicles, or containers used for the storage or shipping of asphalt materials. 1.2. The values stated in S

    3、I units are to be regarded as the standard. The inch-pound units are presented in parentheses for informational purposes and may not be exact equivalents. 1.3. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user

    4、of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 2. SIGNIFICANCE AND USE 2.1. Sampling is a critical step in determining the quality of the material being sampled. Care shall be exercised to ensure that samp

    5、les are representative of the material in the line or vessel being sampled. 2.1.1. Alterations of the materials being sampled, such as the use of filters or screens in the sampling devices or nozzles, shall not occur because such alterations render the sample to not be representative of the material

    6、 remaining in the line or vessel being sampled. 3. INTERFERENCES 3.1. Contamination of samples can occur because of residual amounts of other types and grades of asphalt remaining in the line or vessel being sampled. Contamination can also occur due to the presence of cleaning agents, either in the

    7、line or vessel being sampled or remaining on the sampling devices used. 4. SIZE OF SAMPLES 4.1. The minimum sample size for liquid asphalt material shall be as follows: 4.1.1. 1 L (1 qt) of asphalt binder, or 4.1.2. 4 L (1 gal) of emulsified asphalt. 4.2. The sample size of semisolid or solid materi

    8、als shall be as follows: 4.2.1. From barrels, drums, or cakes1 to 2 kg (2 to 3 lb). 2015 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-2a R 66-2 AASHTO 5. CONTAINERS 5.1. Type of Containers: 5.1.1. Conta

    9、iners for liquid asphalt materials, except emulsified asphalt, shall be double-seal friction-top cans, square cans with screw tops, or small-mouth cans with screw caps. 5.1.2. Containers for emulsified asphalt samples shall be plastic wide-mouth jars or bottles with screw caps. 5.2. Size of Containe

    10、rs: 5.2.1. The size of the container shall correspond to the required amount of sample. Figure 1Examples of Sample Containers 6. PROTECTION AND PRESERVATION OF SAMPLES 6.1. Sample containers shall be new. The top and container shall fit together tightly. 6.2. Take care to prevent the sample from bec

    11、oming contaminated. Immediately after filling it, tightly seal the container. 6.3. The filled sample container shall not be submerged in solvent, nor shall it be wiped with a solvent-saturated cloth. If cleaning is necessary, use only a clean, dry cloth. 6.4. Emulsified asphalt samples shall be prot

    12、ected from freezing. Note 1When sampling emulsified asphalt, do not sample material under pressure. Pressure may allow air entrapment which could result in erroneous test results. Bubbles in the material are one indication that air has been entrapped. In addition, the sampling container should be co

    13、mpletely filled to minimize a skin formation at the air-emulsion interface. 2015 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-2a R 66-3 AASHTO Note 2An alternate to completely filling a container with e

    14、mulsified asphalt is to fill the container until a small amount of space remains. Squeeze the container to cause the contents to fill to the top. Place the cap and securely tighten it. The space remaining will aid in mixing the sample prior to testing. 6.5. Transferring samples from one container to

    15、 another shall be avoided if possible. 6.6. Immediately after filling, sealing, and cleaning, properly identify the sample containers with a suitable marker. Write on the container itself, not on the lid. Labels or tags also may be used for identification if they can be securely fastened to the cont

    16、ainer in such a manner as to ensure that they will not be lost in transit. Labels or tags shall not be attached to containers by using the lids to secure them. All identification materials shall maintain their integrity at temperatures up to 200C (392F). 6.6.1. Label information shall include at a m

    17、inimum: material type, source and sample date. 7. SAMPLING AT PLACE OF MANUFACTURE 7.1. Bulk Storage Tanks Not Equipped with Mechanical Agitators (Liquid Asphalt Materials or Materials Liquefied by Heating)Samples shall be obtained by one of the following methods: 7.1.1. Tank Tap MethodUsing valves

    18、or taps as shown in Figure 2, at the top, middle, and lower locations of the tank, draw a 1- to 4-L (1-qt to 1-gal) sample from each location after clearing the line by drawing and discarding a minimum of 4 L (1 gal) of the material. In the event that only one valve is available at the lower locatio

    19、n, draw a 1- to 4-L (1-qt to 1-gal) sample from the lower location after clearing the line by drawing and discarding a minimum of 4 L (1 gal) of the material. Figure 2Examples of Tank Taps and Valves 2015 by the American Association of State Highway and Transportation Officials.All rights reserved.

    20、Duplication is a violation of applicable law.TS-2a R 66-4 AASHTO 7.1.2. Thief Sampler Method (Not Suitable for Asphalt Binders)Samples shall be taken at the top, middle, and lower levels of the tank by lowering a thief sampler into the material. A satisfactory type of sampler with instructions for u

    21、se is shown in Figure 3. Note: This type of sampler is lowered into the tank with the bottom valve open (there is no top closure). When the desired depth is reached, the lowering chain is given a snap tug which closes the bottom valve. The sampler is then withdrawn from the tank and the contents tra

    22、nsferred to the sample container. This sampler may be used for repetitive sampling in the same tank. Figure 3Example of a Thief Sampler 7.2. Bulk Storage Tanks (Liquid Asphalt Materials or Materials Liquefied by Heating) Equipped with Mechanical AgitatorsWhen the tank is equipped with operating mech

    23、anical agitators which, by observation through the sampling or inspection hatch, are performing adequate mixing of the tank contents, a single sample taken by any of the methods described in Sections 7.1.1 or 7.1.2 will be satisfactory to use for test purposes. 8. SAMPLING FROM TANK CARS, VEHICLE TA

    24、NKS, OR DISTRIBUTOR TRUCKS 8.1. Each delivery vehicle or distributor shall be equipped with a sampling valve similar in design to those shown in Figure 2. It shall be installed at least 305 mm (1 ft) from the shell and clearly labeled as a “Sampling Valve.” Before the sample is taken from the sample

    25、 valve, a minimum of 4 L (1 gal) shall be drawn through the sample valve and discarded. 8.2. When permitted by the purchaser, the following methods may be used to obtain representative samples: 1211107654321 2015 by the American Association of State Highway and Transportation Officials.All rights re

    26、served. Duplication is a violation of applicable law.TS-2a R 66-5 AASHTO 8.2.1. Samples of liquid asphalt materials and materials liquefied by heating may be taken by the “dip method” using a clean wide-mouth plastic jar or friction-top can in a suitable holder. A clean container must be used to tak

    27、e each sample, and the material sampled shall then be transferred to another new and clean container for retaining or testing the sample. 8.2.2. A detachable or permanent sampling pipe fitting, similar in design to the one shown in Figure 4, may be inserted in the discharge line. This outlet assembl

    28、y is to be inserted into the discharge line between the unloading pipe and hose as close to the end as is practical. The sample shall be taken after one third and not more than two thirds of the load has been removed. Before the sample is taken, 4 L (1 gal) shall be drawn from this sampling valve an

    29、d discarded. The sample shall be taken slowly. 8.2.3. If the distributor is not equipped with a sampling valve, a sample may be obtained from a nozzle on the spray bar. Figure 4Typical Detachable Sampling Pipe Fitting Device 9. SAMPLING FROM TANKERS AND BARGES 9.1. For liquid asphalt materials (incl

    30、uding all cutbacks liquefied by heating), samples from the top, middle, and lower levels shall be taken using the methods described in Section 7.1. 9.2. For all other materials liquefied by heating, a sample from the top level only shall be taken by the dip or thief method. FlowBrass Cap76-mm (3-in.

    31、)I.D. Pipe, 305 mm(12 in.) in length13-mm I.D. PipeBrass Capsand Filling13-mm (1/2-in.) I.D. Pipe13-mm (1/2-in.) ValveSide Outlet (vertical position)End ViewTop View13-mm (1/2-in.) Valve Side Outlet(horizontal position) 2015 by the American Association of State Highway and Transportation Officials.A

    32、ll rights reserved. Duplication is a violation of applicable law.TS-2a R 66-6 AASHTO 10. SAMPLING FROM PIPE LINES DURING LOADING OR UNLOADING 10.1. When tankers and barges are being loaded or unloaded, samples may conveniently be taken from the pipe line through which the material is flowing by inse

    33、rtion of a sampling pipe into a rising section of the pipe line on the discharge side of the pump or in a completely filled line in which gravity creates the materials flow. A suitable in-line sampling pipe is shown in Figure 5. The sampling pipe shall be not more than one-eighth the diameter of the

    34、 pipe line and its opening should be turned to face the flow of the liquid. This pipe shall be provided with a valve or plug cock and shall discharge into a sample receiver. At least three 4-L (1-gal) samples shall be taken at uniform intervals throughout the entire loading or unloading operation. A

    35、t the completion of the loading or unloading operation, the individual 4-L (1-gal) samples shall be combined and thoroughly mixed without altering their characteristics, then a 4-L (1-gal) sample shall be taken from the composite. Figure 5Examples of Transfer Line Valve Samplers 10.1.1. When samplin

    36、g tankers or barges less than 4000 m3(25,000 barrels) capacity, at least five 4-L (1-gal) samples shall be taken at uniform intervals throughout the entire loading or unloading operation. Tankers or barges of 4000 m3(25,000 barrels) or larger capacity require at least ten 4-L (1-gal) samples. At com

    37、pletion of the loading or unloading operation, the individual 4-L (1-gal) samples shall be combined and thoroughly mixed without altering their characteristics, then a 4-L (1-gal) sample shall be taken from the composite. 11. SAMPLING FROM DRUMS OR BARRELS 11.1. After thorough mixing, samples of liq

    38、uid asphalt material from barrels or drums shall be secured by the methods described in Section 7.1 by taking 1 L (1 qt) of material from packages selected at random according to Section 12. 12. SAMPLING SEMISOLID MATERIALS 12.1. Drums, Barrels, Cartons, and BagsWhere the lot of material to be sampl

    39、ed is obviously from a single run or batch of the producer, one container shall be selected at random and sampled as described below. Where the lot of material to be sampled is not obviously from a single run or batch of the producer, or where the single sample selected as described above fails on a

    40、 test to conform to the requirements of the specifications, a number of containers equivalent to the cube root of the total number of containers in the lot shall be selected at random. The following table is given, showing the number of samples to be selected for shipments of various sizes. 2015 by

    41、the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-2a R 66-7 AASHTO Table 1Sample Size Selection Containers in Shipment Containers Selected 2 to 8 2 9 to 27 3 28 to 64 4 65 to 125 5 126 to 216 6 217 to 343 7 344

    42、 to 512 8 513 to 729 9 730 to 1000 10 1001 to 1331 11 12.2. Samples shall be taken from at least 75 mm (3 in.) below the surface and at least 75 mm (3 in.) from the side of the container. A clean hatchet may be used if the material is hard enough to shatter or a broad, stiff putty knife may be used

    43、if the material is soft. When more than one container in a lot is sampled, each individual sample shall have a mass of not less than 0.1 kg (1/4lb). When the lot of material is obviously from a single run or batch of the producer, all samples from the lot shall be melted and thoroughly mixed, and an

    44、 average 4-L (1-gal) sample taken from the combined material for examination. If more than a single run or batch of the producer is included and the batches can be clearly differentiated, a composite 4-L (1-gal) sample shall be prepared for examination from each batch. Where it is not possible to di

    45、fferentiate between the various batches, each sample shall be examined separately. 13. SAMPLING AT POINT OF SHIPMENT DELIVERY 13.1. Sampling of asphalt materials shall be completed as soon as practical after the asphalt material has arrived at the plant site, storage site, or job destination or at t

    46、he time of unloading. 13.2. The required number of samples shall be taken from each delivery of asphalt material. In the case of small delivery units such as distributors, the samples shall be taken to represent a maximum of 40 m3(10,000 gal). 13.3. Sampling shall be completed by one of the followin

    47、g methods: 13.3.1. In accordance with Section 7, or 13.3.2. By bleeding through a sample valve or tap in the transfer line during the unloading of the approximate middle-third of the load. 13.4. Tests for material acceptability shall be performed on one of the samples taken. Retain the other samples

    48、 for confirmation if the first sample tested fails to comply with requirements. 14. KEYWORDS 14.1. Asphalt binder; asphalt materials; emulsified asphalt; liquid asphalts; sampling; semisolid materials. 1Formerly T 40. First published as a standard practice in 2015. 2015 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.


    注意事项

    本文(AASHTO R 66-2015 Standard Practice for Sampling Asphalt Materials.pdf)为本站会员(fuellot230)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开