欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    AASHTO R 54-2014 Standard Practice for Accepting Pavement Ride Quality When Measured Using Inertial Profiling Systems.pdf

    • 资源ID:418005       资源大小:105.51KB        全文页数:8页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    AASHTO R 54-2014 Standard Practice for Accepting Pavement Ride Quality When Measured Using Inertial Profiling Systems.pdf

    1、Standard Practice for Accepting Pavement Ride Quality When Measured Using Inertial Profiling Systems AASHTO Designation: R 54-141American Association of State Highway and Transportation Officials 444 North Capitol Street N.W., Suite 249 Washington, D.C. 20001 TS 5a R 54-1 AASHTO Standard Practice fo

    2、r Accepting Pavement Ride Quality When Measured Using Inertial Profiling Systems AASHTO Designation: R 54-1411. SCOPE 1.1. This practice provides guidance and example specification language intended for use by Owner-Agencies in the development of specific contract language when requiring the measure

    3、ment and evaluation of ride quality and compliance using inertial profiling systems (IPS) and the International Roughness Index (IRI) as the quality measure. 1.2. If any part of this practice is in conflict with references made, such as ASTM or AASHTO Standards, this practice takes precedence for it

    4、s purposes. 1.3. The values stated are in U.S. Customary units and are to be regarded as the standard. 1.4. This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate

    5、safety and health practices and determine the applicability of regulatory limitations related to and prior to its use. 2. REFERENCED DOCUMENTS 2.1. AASHTO Standards: M 328, Inertial Profiler R 56, Certification of Inertial Profiling Systems R 57, Operating Inertial Profiling Systems 2.2. ASTM Standa

    6、rds: E867, Standard Terminology Relating to Vehicle-Pavement Systems E1926, Standard Practice for Computing International Roughness Index of Roads from Longitudinal Profile Measurements 2.3. Other Document: Sayers, M. W. “On the Calculation of International Roughness Index from Longitudinal Road Pro

    7、file.” Transportation Research Record 1501. Transportation Research Board, National Research Council, Washington, DC, 1995, pp. 112. 3. TERMINOLOGY 3.1. Definitions: 3.1.1. Inertial Profiling System (IPS)an inertial profiler that meets the requirements of M 328 when combined with an operator. 2016 b

    8、y the American Association of State Highway and Transportation Officials. All rights reserved. Duplication is a violation of applicable law.TS 5a R 54-2 AASHTO 3.1.2. International Roughness Index (IRI)a statistic used to determine the amount of roughness in a measured longitudinal profile. The IRI

    9、is computed from a single longitudinal profile using a quarter-car simulation at 50 mph (Sayers 1995). Computer programs to calculate the IRI from a longitudinal profile are referenced in ASTM E1926. 3.1.3. line lasera line laser obtains a series of data points along a line, which is typically perpe

    10、ndicular to the travel direction, with the line typically being 4 in. long. A single, bridged elevation value is computed from this data. 3.1.4. localized roughnessany 25-ft segment of roadway that contributes disproportionately to the overall roughness index value. Areas of localized roughness are

    11、identified using a report of continuous IRI with a base length of 25 ft. This yields the IRI of every possible 25-ft segment. Any segment for which the continuous report exceeds a threshold IRI value is considered a defective segment requiring correction. Note 1The threshold IRI value in inches per

    12、mile should be determined by each Owner-Agency. A typical range of values for various highway types is shown in Table 1. Table 1Typical Threshold Values for Localized Roughness Roadway Type IRI (in./mile) Interstate 140 to 160 State primary 150 to 170 State secondary 160 to 190 3.1.5. longitudinal p

    13、rofilethe vertical deviations of the pavement surface taken along a line in the direction of travel referenced to a horizontal datum. 3.1.6. report intervalthe longitudinal distance between the outputs of a profile index value. 3.1.7. roughness according to ASTM E867, the deviation of a surface from

    14、 a true planar surface with characteristic dimensions that affects vehicle dynamics, ride quality, dynamic loads, and drainage. 3.1.8. Type A Roughness Measurementa test procedure to measure the longitudinal profile of a surface using an inertial profiler and to compute the profile index known as th

    15、e International Roughness Index (IRI). 3.1.9. Type B Roughness Measurementa test procedure to measure surface profile deviations using a straightedge. 4. SIGNIFICANCE AND USE 4.1. This example provides specification language for measuring and accepting ride quality on newly constructed paving projec

    16、ts using an IPS and the IRI quality measure. If an Owner-Agency elects to use some other ride quality index, the fundamental methodology described herein remains valid, but not the individual settings. Note 2The IPS should be verified on the same pavement surface type and texture as that being measu

    17、red. When profiling pavements with rough macrotexture, a height sensor with a large footprint is needed. A line laser that utilizes a bridging algorithm is an example of a sensor with a large footprint. The consequence of not using a large footprint sensor may be an upward bias in the IRI as measure

    18、d by an IPS with a single-point (dot) laser. An IPS with a single-point laser can also collect inaccurate data on longitudinally tined, longitudinally grooved, or diamond ground pavements. A line laser that utilizes a bridging algorithm is recommended for such pavements. 2016 by the American Associa

    19、tion of State Highway and Transportation Officials. All rights reserved. Duplication is a violation of applicable law.TS 5a R 54-3 AASHTO 5. EQUIPMENT AND OPERATOR 5.1. Provide an approved 10-ft straightedge. 5.2. Provide an inertial profiler meeting all requirements and specifications found in M 32

    20、8 and currently certified in accordance with R 56. Operate the equipment in accordance with R 57. 5.3. Provide the Owner-Agency a copy of the equipment certification. Display a current decal on the equipment indicating the expiration date of certification. Note 3An equipment certification or decal w

    21、ould be required only if the Owner-Agency had a certification program that issued them, or where it recognizes another agencys certification program in which certifications, decals, or both are issued. 5.4. Provide a qualified profiler operator. Provide the Owner-Agency a copy of the operators quali

    22、fications or current certification. 6. WORK METHODS 6.1. Quality Control (QC) Testing (nondirected)Perform QC tests on a daily basis throughout the duration of the project. Use an approved straightedge, inertial profiler, profilograph, or any other appropriate means. 6.2. Quality Control Testing (di

    23、rected)Use Type A Roughness Measurement. Use Type B Roughness Measurement only when Type A Roughness Measurement cannot be used or when specified by the Owner-Agency. Measure the finished surface of the completed project or at the completion of a major stage of construction as approved by the Owner-

    24、Agency. Coordinate with and receive authorization from the Owner-Agency before starting testing. Obtain roughness measurements within 7 days after receiving authorization and submit results to the Owner-Agency within 24 h of data collection. 6.2.1. Operate the profiler in accordance with R 57 and pr

    25、ovide the Owner-Agency the results of the Daily Measurement Control on a daily basis. The Owner-Agency may require QC testing be performed at off-peak times for traffic flow. Operate the inertial profiler in a manner that does not unduly disrupt traffic flow as determined by the Owner-Agency. Use an

    26、 approved traffic control plan. Traffic control for QC and verification testing by the Owner-Agency is at the expense of the contractor. Provide all profile measurements to the Owner-Agency in electronic data files of the format specified in R 57. 6.3. Verification TestingWithin 10 working days afte

    27、r the contractors QC testing under Section 6.2 is completed, the Owner-Agency may perform verification testing using an inertial profiler meeting the requirements of R 56. If the verification testing produces an IRI obtained over the same section of roadway that differs from that obtained using the

    28、contractors profiler by more than the percentages shown in Table 2, then the Owner-Agency and contractor shall attempt to resolve the differences to their mutual satisfaction. 2016 by the American Association of State Highway and Transportation Officials. All rights reserved. Duplication is a violat

    29、ion of applicable law.TS 5a R 54-4 AASHTO Table 2Typical Allowable IRI Differences Mean of Agency and Contractors IRI (in./mile) Max Allowable DifferenceaLess than 50 8.5% of mean IRI 50 to 150 6.0% of mean IRI Greater than 150 7.0% of mean IRI a Actual values should be set by the Owner-Agency. 6.3.

    30、1. If the differences cannot be resolved, then referee testing will be conducted. The Owner-Agency will conduct the referee testing and the results will be final and will be used to establish pay adjustments. Referee testing will be conducted using an inertial profiler that recently has been certifi

    31、ed in accordance with R 56. The certification should not be more than 90 days old unless both parties agree otherwise. 6.3.2. If the testing confirms the Owner-Agency profiler and fails to confirm the contractors profiler, then the contractors profiler shall be taken out of service until it has been

    32、 recertified in accordance with R 56. A similar requirement will apply if the testing confirms the contractor equipment but fails to confirm the Owner-Agency. If the referee testing fails to confirmeither the Owner-Agency or contractor equipmentthen both profilers shall be removed from service until

    33、 recertified. 6.4. Evaluation of ProfilesThe contractor shall evaluate profiles for acceptance, incentive payments, disincentive payments, or corrective action using the current version of ProVAL and provide the results to the Owner-Agency within 24 h of completing testing under Section 6.2. If the

    34、profile data files are created using an export option in the manufacturers software where filter settings can be specified, use the filter settings that were used to create data files for certification. Analyze the entire profile. Exclude any areas specifically identified in the contract. Exclude fr

    35、om the analysis for localized roughness the first 12.5 ft after the start of the paving operations and last 12.5 ft prior to the end of the paving operation. Also exclude the first 12.5 ft on either side of bridge structures, manhole covers, utility covers, and approach slabs. Determine pay adjustme

    36、nts in accordance with Sections 6.4.3 and 6.4.4. The Owner-Agency will verify the analysis. Note 4The Profile Viewer and Analysis (ProVAL) software program developed for the Federal Highway Administration, which can be used to import, display, and analyze the characteristics of pavement profiles fro

    37、m many different sources, is available at . 6.4.1. Type A Roughness MeasurementThe Owner-Agency may use the QC test results obtained under Section 6.2 to determine pay adjustments for ride quality provided it is able to verify the contractors profile data. Areas excluded from measurement under Type

    38、A Roughness Measurement shall be measured in accordance with Section 6.4.2. 6.4.2. Type B Roughness MeasurementTypically used where an IPS cannot be effectively operated. There are no pay adjustments when Type B Roughness Measurement is used. In a manner approved by the Owner-Agency, correct surface

    39、 areas that have more than 1/4-in. variation between any two contacts on the straightedge. There is no payment for correcting deficient areas. Following correction, retest the area to verify compliance. 6.4.3. Pay Adjustment ScheduleThe pay adjustment factors from Table 3 will be used in conjunction

    40、 with the histogram printout from ProVALs Smoothness Assurance Module, based on a report of continuous IRI with a base length of 528 ft, to compute a final pay factor (incentive or disincentive). The final pay factor (PF), computed to three decimals, is equal to the sum of the products of the indivi

    41、dual pay adjustment factors shown in Table 3 times ProVALs corresponding histogram percentages divided by 100. In addition to the final pay factor determined from Table 3, disincentives for localized roughness may apply as described in Section 6.4.4. 2016 by the American Association of State Highway

    42、 and Transportation Officials. All rights reserved. Duplication is a violation of applicable law.TS 5a R 54-5 AASHTO Table 3Pay Adjustment Factors and Computation of Final Pay Factor IRI Range, in./milea(1) Pay Adjustment Factors (2) Percent of Pavement within IRI Range Taken from ProVALs Smoothness

    43、 Assurance Module (SAM) (3) Pay Adjustment (4) #.0 0.# #.# or #.# #.# or #.# #.1 #.0 0.# #.# or #.# #.# or #.# #.1 #.0 0.# #.# or #.# #.# or #.# #.1 #.0 0.# #.# or #.# #.# or #.# #.1 #.0 1.00 #.# or #.# #.# or #.# #.1 #.0 1.# #.# or #.# #.# or #.# #.1 #.0 1.# #.# or #.# #.# or #.# #.1 #.0 1.# #.# or

    44、 #.# #.# or #.# #.0 0.# #.# or #.# #.# or #.# #.1 #.0 0.# #.# or #.# #.# or #.# #.1 #.0 0.# #.# or #.# #.# or #.# #.1 #.0 0.# #.# or #.# #.# or #.# #.0 1.00 #.# or #.# #.# or #.# Final % disincentive = (100 sum) = #.# or #.# aThe number of steps in the table as well as the IRI ranges and pay adjustm

    45、ent factors should be set by the Owner-Agency. Note 6A different set of pay adjustment factors may be used for different project requirements. This pay adjustment table is just one style of many possible pay tables and was designed to utilize quality assurance features within ProVAL. For this table

    46、the final percent disincentive is determined by taking the values in column (2) and multiplying them by column (3). The results are shown in column (4). The results in column (4) are then summed and subtracted from 100 to obtain the final percent disincentive. 2016 by the American Association of Sta

    47、te Highway and Transportation Officials. All rights reserved. Duplication is a violation of applicable law.TS 5a R 54-6 AASHTO 6.4.5. Deficiencies and Corrective WorkAll corrective work will be at the contractors expense. 6.4.5.1. A defective segment is any area of localized roughness as determined

    48、in Section 6.4.4. 6.4.5.2. Propose a plan and methodology to correct deficiencies and receive approval from the Owner-Agency before beginning any corrective work. This must be done with the purpose of correcting the minimum area needed to decrease the roughness to acceptable limits. ProVALs Smoothne

    49、ss Assurance Module is an example of a computer program that can be used to assist in developing a plan. 6.4.5.3. The Owner-Agency will determine the final disposition of defective segments, which may include corrective actions, assessment of a penalty, or some combination thereof. 6.4.5.4. After making corrections, reprofile the corrected pavement section to verify that the corrections have produce


    注意事项

    本文(AASHTO R 54-2014 Standard Practice for Accepting Pavement Ride Quality When Measured Using Inertial Profiling Systems.pdf)为本站会员(eveningprove235)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开