欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    AASHTO MP 32-2017 Standard Specification for Materials for Slurry Seal.pdf

    • 资源ID:417869       资源大小:131.84KB        全文页数:4页
    • 资源格式: PDF        下载积分:2000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要2000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    AASHTO MP 32-2017 Standard Specification for Materials for Slurry Seal.pdf

    1、Standard Specification for Materials for Slurry Seal AASHTO Designation: MP 32-171Technical Section: 2a, Emulsified Asphalts Release: Group 3 (August 2017) American Association of State Highway and Transportation Officials 444 North Capitol Street N.W., Suite 249 Washington, D.C. 20001 TS-2a MP 32-1

    2、 AASHTO Standard Specification for Materials for Slurry Seal AASHTO Designation: MP 32-171Technical Section: 2a, Emulsified Asphalts Release: Group 3 (August 2017) 1. SCOPE 1.1. This standard covers requirements for emulsified asphalt, aggregate, mineral filler, water, and additive materials used in

    3、 slurry seals. Slurry seals are mixed and placed on existing pavement surfaces using specially designed paving machines. 2. REFERENCED DOCUMENTS 2.1. AASHTO Standards: M 17, Mineral Filler for Bituminous Paving Mixtures M 85, Portland Cement M 208 Standard Specification for Cationic Emulsified Aspha

    4、lt M 295, Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete M 303, Lime for Asphalt Mixtures PP 87, Slurry Seal Design T 11, Materials Finer Than 75-m (No. 200) Sieve in Mineral Aggregates by Washing T 27, Sieve Analysis of Fine and Coarse Aggregates T 96, Resistance to Degradati

    5、on of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine T 104, Soundness of Aggregate by Use of Sodium Sulfate or Magnesium Sulfate T 176, Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test T 335, Determining the Percentage of Fracture in Coar

    6、se Aggregate 2.2. ANSI Standard: NSF/ANSI 60-2013, Drinking Water Treatment Chemicals-Health Effects 3. TERMINOLOGY 3.1. CQS-1Ha cationic, quick-setting emulsified asphalt. 4. SIGNIFICANCE AND USE 4.1. This standard may be used to select and evaluate materials for the construction of slurry seal. Th

    7、e design recommendations for slurry seal may be found in PP 87. 2017 by the American Association of State Highway and Transportation Officials. All rights reserved. Duplication is a violation of applicable law.TS-2a MP 32-2 AASHTO 5. EMULSIFIED ASPHALT REQUIREMENTS 5.1. Emulsified asphalt for slurry

    8、 seal shall meet the requirements of CQS-1h in M 208. Alternate emulsified asphalt classifications may be specified by the Owner Agency utilizing regional climatic and traffic conditions as well as local nomenclature. 6. AGGREGATE REQUIREMENTS 6.1. Mineral aggregate shall be 100 percent crushed on t

    9、wo or more faces for the coarse aggregate material retained on the 2.36 mm (No. 8) sieve. Only manufactured fine aggregate, material passing the 2.36 mm sieve (No. 8), is permitted. T 335 shall be used to determine the percentage of crushed aggregate. The quality requirements for the aggregates shal

    10、l be in accordance with Table 1. The grading of the aggregate in Table 2 shall be specified by the Owner Agency. Table 1Aggregate Quality Requirements Test Test Method Requirement Sand Equivalent, min T 176 45 Los Angeles Abrasion, %, maxaT 96 35 Magnesium Sulfate Soundness, max loss, %, 5 cycles T

    11、104 20 Sodium Sulfate Soundness, max loss, %, 5 Cycles T 104 15 a The abrasion test is to be run on the parent aggregate, i.e. limestone, sandstone, etc. from which it was derived. Table 2Aggregate Grading Requirements Sieve Size Type IIaPercent Passing Type IIIbPercent Passing Stockpile Tolerance %

    12、 9.5 mm(3/8 in) 100 100 4.75 mm (No. 4) 90100 70 90 5 2.36 mm (No. 8) 6590 4570 5 1.18 mm (No. 16) 4570 2850 5 600 m (No. 30) 3050 1934 5 330 m (No. 50) 1830 1225 4 150 m (No. 100) 1021 718 3 75 m (No. 200) 515 515 2 aType II aggregates are typically used to fill surface voids, address surface distr

    13、esses (scratch courses), seal, and provide a durable wearing surface. bType III aggregates are typically used to provide higher friction resistance and an improved wearing surface. 6.2. When tested in accordance with T 11 and T 27 the mix design aggregate gradation shall comply with one of the grada

    14、tions in Table 2 or one designated by the Owner Agency. 6.3. The gradation of the aggregate stockpile shall not vary from the mix design gradation by more than the stockpile tolerance, indicated in Table 2, while also remaining within the specifications gradation band. The percentage of aggregate pa

    15、ssing any two successive sieves shall not change from one end of the specified range to the other end. 7. MINERAL FILLER 7.1. Mineral filler may be used to improve mixture consistency and to adjust mixture breaking and curing properties. Portland cement, hydrated lime, limestone dust, fly ash, or ot

    16、her approved filler meeting the requirements of M 17, M 85, M 295, or M 303 shall be used if required by the mix 2017 by the American Association of State Highway and Transportation Officials. All rights reserved. Duplication is a violation of applicable law.TS-2a MP 32-3 AASHTO design. Aluminum sul

    17、fate shall meet the requirements of NSF/ANSI 60. Typical mineral filler use levels are 0 to 3.0 percent by mass and may be considered part of the aggregate gradation. 8. WATER 8.1. Water shall be free of harmful salts and contaminants. If the quality of the water is in question, it should be submitt

    18、ed to the mix design laboratory for analysis along with the other raw materials to be used in the mix design. 9. ADDITIVES 9.1. Additives may be used to accelerate or retard the break or set of the slurry seal material. Appropriate additives such as emulsified chemicals, and their applicable use ran

    19、ge, should be approved by the mix design laboratory as part of the mix design process. 10. KEYWORDS 10.1. Emulsified asphalt; mineral aggregate; mineral filler; slurry seal. 1This provisional standard was first published in 2017. 2017 by the American Association of State Highway and Transportation Officials. All rights reserved. Duplication is a violation of applicable law.


    注意事项

    本文(AASHTO MP 32-2017 Standard Specification for Materials for Slurry Seal.pdf)为本站会员(appealoxygen216)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开