欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    AASHTO HB-17 DIVISION II SEC 29-2002 Division II Construction - Embedment Anchors《埋锚》.pdf

    • 资源ID:417596       资源大小:102.36KB        全文页数:2页
    • 资源格式: PDF        下载积分:2000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要2000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    AASHTO HB-17 DIVISION II SEC 29-2002 Division II Construction - Embedment Anchors《埋锚》.pdf

    1、29.1 DESCRIPTION Section 29 EMBEDMENT ANCHORS This specification covers installation and field testing of cast-in-place, grouted, adhesive-bonded, expansion and undercut steel anchors. 29.2 PREQUALIFICATION Prequalify all concrete anchors, including cast-in- place, all bonded anchor systems (includi

    2、ng grout, chem- ical compounds, and adhesives), and undercut by univer- sal test standards designed to allow approved anchor systems to be employed for any construction attachment use. Conduct test for adhesive-bonded and other bonding compounds in accordance with ASTM E 1512 (Standard Test Methods

    3、for Testing Bond Performance of Adhesive- Bonded Anchors). Test expansion types to ASTM E 488 (Standard Test Methods for Strength of Anchors in Concrete and Ma- sonry Elements). Comply with AC1 349-85 (Code Requirements for Nuclear Safety Related Concrete Structures-Appendix B, Steel Embedments). Pr

    4、ovide certified test reports prepared by an indepen- dent laboratory documenting that the system (except me- chanical expansion anchors) is capable of achieving the minimum tensile strength of the embedment steel. 29.3 MATERIALS Provide mill test reports certifying physical properties, chemistry, an

    5、d strengths. The chemical compounds acceptable for adhesive an- chors may include epoxies, polyesters, or vinylesters. Ad- hesive compounds which are moisture-insensitive, high- modulus, high-strength, and low-shrinkage should be used. The use of additives to grout, and bonding materials which will

    6、be corrosive to steel or zinckadmium coatings is prohibited. 29.4 CONSTRUCTION METHODS Provide adequate edge distance, embedment depth and spacing to develop the required strength of the embed- ment anchors. Use the correct drill hole diameter as per manufacturers instructions. Use rotary impact dri

    7、lling equipment unless diamond core drilling has been speci- fied and tested. If reinforcing bar is encountered during the drilling operation, move to a different location, or drill through the reinforcing steel using a diamond core bit as directed by the Engineer. Patch abandoned holes with an appr

    8、oved bonding material. Clean holes thoroughly as recommended by the manufacturer. Remove all loose dust and concrete particles from hole. Prepare bonding mater- ial and install anchors according to instructions provided by the manufacturer or approved by the Engineer. Embedded anchors which are impr

    9、operly installed or which do not have the required strength shall be remdved and replaced to the satisfaction of the Engineer at the Contractors expense. 29.5 INSPECTION AND TESTING Where specified, conduct sacrificial tests of the anchor system on the job site to ultimate loads to document the capa

    10、bility of the system to achieve pullout loads equaling the full minimum tensile value of the anchor employed. Test the anchor on fully cured concrete samples. Unless specified otherwise, test no fewer than three (3) anchors by ASTM E 488 methods. The Contractor may use any pre- qualified anchor syst

    11、ems meeting the above requirements. Provide, without delay in progress, for an alternate sys- tem that will reach the designated pull-out requirement if the job site proofloading proves incapable of achieving minimum tensile values (or the designers required load if too little concrete exists in whi

    12、ch to develop full ductile loads). After installing the curing of bonding material, torque each anchor system to values specified. If torque values are not specified, use values recommended by the manu- facturer or provided by the Engineer. 685 686 HIGHWAY BRIDGES 29.6 29.6 MEASUREMENT 29.7 PAYMENT

    13、Count and summarize each embedment anchor type satisfactorily installed for the Contract, according to an- chor system, orientation (vertical, diagonal, and horizon- tal), and size (diameter). Payment for the quantity of embedment anchors deter- mined under measurement for each embedment anchor type, shall include full compensation for furnishing all labor, materials, tools, equipment, testing, and incidentals necessary to place each anchor type.


    注意事项

    本文(AASHTO HB-17 DIVISION II SEC 29-2002 Division II Construction - Embedment Anchors《埋锚》.pdf)为本站会员(sofeeling205)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开