欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ABS 177 NOTICE 1-2013 GUIDE FOR SLAMMING LOADS AND STRENGTH ASSESSMENT FOR VESSELS.pdf

    • 资源ID:400690       资源大小:54.22KB        全文页数:5页
    • 资源格式: PDF        下载积分:2000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要2000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ABS 177 NOTICE 1-2013 GUIDE FOR SLAMMING LOADS AND STRENGTH ASSESSMENT FOR VESSELS.pdf

    1、 ABSGUIDE FOR SLAMMING LOADS AND STRENGTH ASSESSMENT FOR VESSELS .2011 1 GUIDE FOR SLAMMING LOADS AND STRENGTH ASSESSMENT FOR VESSELS MARCH 2011 NOTICE NO. 1 July 2013 The following Rule Changes were approved by the ABS Rules Committee on 31 May 2013 and become EFFECTIVE AS OF 1 JULY 2013. (See http

    2、:/www.eagle.org for the consolidated version of the Guide for Slamming Loads and Strength Assessment for Vessels, 2011, with all Notices and Corrigenda incorporated.) Notes - The date in the parentheses means the date that the Rule becomes effective for new construction based on the contract date fo

    3、r construction. (See 1-1-4/3.3 of the ABS Rules for Conditions of Classification (Part 1).) SECTION 8 DIRECT STRENGTH ASSESSMENT 3 Shell Plating 3.1 Bowflare Slamming (1 July 2013) (Revise definition of f1, as follows.) f1= 0.90Smfyfor side shell plating in the region forward of 0.125L, from the for

    4、ward perpendicular, in N/cm2(kgf/cm2, lbf/in2) = 0.75Smfyfor side shell plating in the region between 0.125L and 0.25L, from the forward perpendicular 5 Shell Longitudinals and Stiffeners (Revise Paragraph 8/5.1, as follows.) 5.1 Bowflare Slamming (1 July 2013) The net section modulus of the shell l

    5、ongitudinal (or frame), including the associated effective plating, is not to be less than that obtained from the following equation: SM = M/fbcm3(in3) M = ps s2103/k N-cm (kgf-cm, lbf-in) where k = 16 (16, 111.1) ps= design slamming pressure as described in Subsection 7/3, in N/cm2(kgf/cm2, lbf/in2

    6、) s = spacing of longitudinal or transverse frames, in mm (in.) Notice No. 1 July 2013 2 ABSGUIDE FOR SLAMMING LOADS AND STRENGTH ASSESSMENT FOR VESSELS .2011 = unsupported span of the frame, in m (ft) fb= 0.9Smfyfor transverse and longitudinal frames in the region forward of 0.125L from the FP, in

    7、N/cm2(kgf/cm2, lbf/in2) = 0.8Smfyfor transverse and longitudinal stiffeners in the region between 0.125L and 0.25L, measured from the FP, in N/cm2(kgf/cm2, lbf/in2) = 0.95Smfyfor stern slamming, in N/cm2(kgf/cm2, lbf/in2) Smand fyare defined in Subsection 8/3. The associated effective breadth of pla

    8、ting is to be taken as spacing of longitudinal or transverse frames or 20% of the unsupported span, whichever is less. (Revise Paragraph 8/5.3 and add new Figure 1, as follows.) 5.3 Bottom and Stern Slamming (1 July 2013) In case of bottom or stern slamming, an ultimate strength approach considering

    9、 plasticity may be employed to estimate section modulus to the corresponding slamming pressure. The net plastic section modulus, SMpl, of each individual stiffener, is not to be less than: SMpl= yabdgsfCfskp2cm3 (in3) where k = 1000 (1000, 144) ps= slamming pressure as described in Subsection 7/3, i

    10、n N/cm2(kgf/cm2, lbf/in2) s = spacing of longitudinal or transverse frames, in mm (in.) = unsupported span of the frame, in m (ft) fbdg= bending moment factor = +218snns= 2.0 for continuous stiffeners or where stiffeners are bracketed at both ends Ca= permissible bending stress coefficient = 0.9 fy=

    11、 minimum specified yield point of the material, in N/cm2(kgf/cm2, lbf/in2) The associated effective breadth of plating may be taken as the spacing of longitudinal or transverse frames. The net plastic section modulus can be calculated using the following formulae. When the cross-sectional area of th

    12、e attached plate exceeds the cross-sectional area of the stiffener to which the plate flange is attached, the actual net plastic section modulus, Zp, in cm3(cm3, in3) is given by: Zp= Apntpn/(2 c4) + 3422sincthwwnw+ Afn(hfcsin w bwcos w)/c4where Apn= net cross-sectional area of the attached plate, i

    13、n cm2(cm2, in2) tpn= net attached plate thickness, in mm (mm, in.) Notice No. 1 July 2013 ABSGUIDE FOR SLAMMING LOADS AND STRENGTH ASSESSMENT FOR VESSELS .2011 3 hw= height of stiffener web, in mm (mm, in.), see Section 8, Figure 1 Afn= net cross-sectional area of stiffener flange, in cm2(cm2, in2)

    14、hfc= height of stiffener measured to center of the flange area, mm (mm, in.), see Section 8, Figure 1 bw= distance from mid thickness plane of stiffener web to the center of the flange area, in mm (mm, in.), see Section 8, Figure 1 c4= 10 (10, 1) h = height of stiffener, in mm (mm, in.), see Section

    15、 8, Figure 1 twn= net web thickness, in mm (mm, in.) = tw tctw= gross web thickness, in mm (mm, in.), see Section 8, Figure 1 tc= corrosion deduction, in mm (mm, in.), to be subtracted from the web and flange thickness w= smallest angle between attached plate and stiffener web, measured at the midsp

    16、an of the stiffener, see Section 8, Figure 1. The angle wmay be taken as 90 degrees provided the smallest angle is not less than 75 degrees. s = spacing of longitudinal or transverse frames, in m (m, in.) When the cross-sectional area of the stiffener exceeds the cross-sectional area of the attached

    17、 plate, the plastic neutral axis is located a distance zna, in mm (mm, in.), above the attached plate, given by: zna= (24c Afn+ hwtwn 34c tpns)/(2 twn) and the net plastic section modulus, Zp, in cm3(cm3, in3) is given by: Zp= tpns(zna+ tpn/2)sin w+ +43422/cossin)(2sin)(cbzhActzzhwwwnafcfnwwnnanawFI

    18、GURE 1 Stiffener Geometry (1 July 2013) stpbfbwhwtwhhfcw(Renumber subsequent figures in Section 8 accordingly.) Notice No. 1 July 2013 4 ABSGUIDE FOR SLAMMING LOADS AND STRENGTH ASSESSMENT FOR VESSELS .2011 7 Slot Connections (1 July 2013) (Revise Subsection 8/7, as follows.) Each slot connection un

    19、der the design slamming pressure is to be verified using the following formulae: fb= P1/As58 for Asin in2= 1.85 for As 2.2 = 1.85 0.2883(As 2.2) for 2.2 9.0 For intersecting of asymmetrical stiffeners = 0.68 + 0.0172 d/Asfor din cmand Asin cm2= 0.68 + 0.00677 d/Asfor din inches and Asin in2If the length of direct and shear connections are different, their mean value is to be used instead of d, and in case of a single lug, the value is c. Smand fyare as defined in Subsection 8/3. For flat bar stiffener with soft-toed brackets, the brackets may be included in the calculation of As.


    注意事项

    本文(ABS 177 NOTICE 1-2013 GUIDE FOR SLAMMING LOADS AND STRENGTH ASSESSMENT FOR VESSELS.pdf)为本站会员(eventdump275)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开