1、BSI Standards Publication BS ISO 6722-2:2013 Road vehicles 60 V and 600 V single-core cables Part 2: Dimensions, test methods and requirements for aluminium conductor cablesBS ISO 6722-2:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6722-2:2013. The UK
2、 participation in its preparation was entrusted to Technical Committee AUE/16, Electrical and electronic equipment. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contra
3、ct. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 69945 0 ICS 43.040.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the
4、authority of the Standards Policy and Strategy Committee on 31 December 2013. Amendments issued since publication Date Text affectedBS ISO 6722-2:2013 ISO 2013 Road vehicles 60 V and 600 V single-core cables Part 2: Dimensions, test methods and requirements for aluminium conductor cables Vhicules ro
5、utiers Cbles monoconducteurs de 60 V et 600 V Partie 2: Mthodes dessai des dimensions et exigences pour les cbles conducteurs en aluminium INTERNATIONAL STANDARD ISO 6722-2 Fourth edition 2013-12-01 Reference number ISO 6722-2:2013(E)BS ISO 6722-2:2013ISO 6722-2:2013(E)ii ISO 2013 All rights reserve
6、d COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written
7、 permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS IS
8、O 6722-2:2013ISO 6722-2:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 1 4 General 1 4.1 Safety concerns . 1 4.2 Temperature classes . 2 4.3 Conductors . 2 4.4 Tests 2 4.5 General test conditions 3 4.6
9、 Ovens . 3 4.7 Representative conductor sizes for testing 4 4.8 Recommended colours. 4 5 Tests . 4 5.1 Outside cable diameter 4 5.2 Insulation thickness 5 5.3 Conductor diameter and cross-sectional area . 6 5.4 Conductor resistance . 8 5.5 Withstand voltage 9 5.6 Insulation faults . 9 5.7 Insulation
10、 volume resistivity 9 5.8 Pressure test at high temperature .10 5.9 Strip force .10 5.10 Low temperature winding .10 5.11 Cold impact .10 5.12 Abrasion test 10 5.13 Long-term heat ageing, 3 000 h .10 5.14 Short-term heat ageing, 240 h 10 5.15 Thermal overload 10 5.16 Shrinkage by heat 10 5.17 Resist
11、ance to chemicals 10 5.18 Durability of cable marking 10 5.19 Resistance to ozone 10 5.20 Resistance to hot water 11 5.21 Temperature and humidity cycling 11 5.22 Resistance to flame propagation 11 Annex A (informative) Conductor sizes and cable dimensions12 Annex B (normative) Det ermination of t e
12、mper atur e c oefficients .14 Bibliography .16BS ISO 6722-2:2013ISO 6722-2:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out throu
13、gh ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collabora
14、tes closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval c
15、riteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subjec
16、t of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade
17、name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Tech
18、nical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 3, Electrical and electronic equipment. This fourth edition of ISO 6722-2 cancels and replaces ISO 6722:2006. ISO 6722 co
19、nsists of the following parts, under the general title Road vehicles 60 V and 600 V single- core cables: Part 1: Dimensions, test methods and requirements for copper conductor cables Part 2: Dimensions, test methods and requirements for aluminium conductor cablesiv ISO 2013 All rights reservedBS ISO
20、 6722-2:2013ISO 6722-2:2013(E) Introduction ISO 6722 deals with single-core cables, with copper conductor cables covered in ISO 6722-1 and aluminium conductor cables covered in this part of ISO 6722. The performance of aluminium conductor cables is, in general, not to be expected to be the same as t
21、he performance of copper conductor cables in a one-to-one comparison basis. ISO 2013 All rights reserved vBS ISO 6722-2:2013BS ISO 6722-2:2013Road vehicles 60 V and 600 V single-core cables Part 2: Dimensions, test methods and requirements for aluminium conductor cables WARNING The use of this part
22、of ISO 6722 may involve hazardous materials, operations, and equipment. This part of ISO 6722 does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this part of ISO 6722 to establish appropriate safety practices and determine
23、 the applicability of regulatory limitations prior to use. 1 Scope This part of ISO 6722 specifies the dimensions, test methods, and requirements for single-core 60 V cables intended for use in road vehicle applications where the nominal system voltage is 60 V d.c. or 25 V a.c. It also specifies add
24、itional test methods and/or requirements for 600 V cables intended for use in road vehicle applications, where the nominal system voltage is from 60 V d.c. or 25 V a.c. to 600 V d.c. or 600 V a.c. It also applies to individual cores in multi-core cables. This part of ISO 6722 specifies requirements
25、for aluminium conductor cables. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenc
26、ed document (including any amendments) applies. ISO 6722-1, Road vehicles 60 V and 600 V single-core cables Part 1: Dimensions, test methods and requirements for copper conductor cables ISO 6892-1, Metallic materials Tensile testing Part 1: Method of test at room temperature EN 573-1, Aluminium and
27、aluminium alloys Chemical composition and form of wrought products Part 1: Numerical designation system EN 573-3:2009, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition and form of products 3 T erms a nd definiti ons For the purposes of thi
28、s document, the terms and definitions given in ISO 6722-1 apply. NOTE Whenever a.c. voltage is specified throughout this part of ISO 6722, the a.c. rms value shall be used. 4 General 4.1 Safety concerns See “WARNING” at the beginning of this part of ISO 6722. INTERNATIONAL ST ANDARD ISO 6722-2:2013(
29、E) ISO 2013 All rights reserved 1BS ISO 6722-2:2013ISO 6722-2:2013(E) 4.2 Temperature classes Temperature classes are defined in Table 1. Table 1 Temperature class rating Class Temperature A 40 C to 85 C B 40 C to 100 C C 40 C to 125 C D 40 C to 150 C E 40 C to 175 C F 40 C to 200 C 4.3 Conductors T
30、he conductors shall consist of annealed or annealed compressed/compacted aluminium, aluminium alloy, or copper-cladded aluminium strands. The specifications for the conductors shall be according to Table 2 and shall be completed by material specifications. Elongation requirements shall be establishe
31、d by the agreement between the customer and the supplier. The finished cable shall meet the resistance requirements of Table 5 for all conductors. The individual strands of the aluminium conductor shall be manufactured per 1 000 series aluminium, pursuant to EN 573-1. The chemical composition shall
32、follow EN 573-3:2009, Table 1. NOTE Examples of strandings are shown in Table A.1. These strandings highlight examples of conceptual configurations and are not intended to reflect any preferred constructions. Other stranding configurations may be used provided they meet the requirements specified an
33、d are agreed upon by the customer and the supplier. Table 2 Characteristics of individual single strand wire after annealing Tensile strength a,bRm MPa Elongation at break aA C% Conductivity 20Sm/mm 2 70 to 120 16 35,5 90 to 140 c,d 8 c,d 33,5 d aDetermined pursuant to ISO 6892-1, (Reference 2). bMe
34、asured at clamping length of 200 mm. cNot applicable for compressed conductors. The tensile strength, elongation, and chemical composition requirements shall be established by the agreement between the customer and the supplier. dAdditional aluminium alloys may be used. The conductivity, tensile str
35、ength, elongation requirements, and chemical composition shall be established by the agreement between the customer and the supplier. 4.4 Tests The cables shall be submitted to tests as specified in Table 3. Unintended direct contact of aluminium wire with any other metal shall not occur with any of
36、 the test methods.2 ISO 2013 All rights reservedBS ISO 6722-2:2013ISO 6722-2:2013(E) 4.5 General test conditions If not otherwise specified, the device under test (DUT) shall be preconditioned for at least 16 h at a room temperature (RT) of (23 5) C and a relative humidity (RH) of 45 % to 75 %. Unle
37、ss otherwise specified, all tests other than “in-process” tests shall be conducted at these conditions. Where no tolerance is specified, all values shall be considered to be approximate. When a.c. tests are performed, these shall be carried out at 50 Hz or 60 Hz. Applications at higher frequencies m
38、ay require additional testing. 4.6 Ovens An oven with air exchange, either natural or by pressure, should be used. The air shall enter the oven in such a way that it flows over the surface of the test pieces and leaves near the top of the oven. The oven shall have not less than 8 and not more than 2
39、0 complete air changes per hour at the specified ageing temperature. Forced air circulation, e.g. by a fan, inside the oven may be used. However, in case of dispute, an oven without forced air circulation shall be used. Table 3 Tests Subclause Test description Mandatory If required c In-process a In
40、itial Periodic b Initial Periodic b Dimensions 5.1 Outside cable diameter X X 5.2 Insulation thickness X X 5.3 Conductor diameter and cross-sectional area X X X X Electrical characteristics 5.4 Conductor resistance X X 5.5 Withstand voltage X d X d 5.6 Insulation faults X d 5.7 Insulation volume res
41、istivity X X Mechanical characteristics 5.8 Pressure test at high temperature X X 5.9 Strip force X X Low temperature characteris- tics 5.10 Winding X X 5.11 Impact X X 5.12 Resistance to abrasion X e X e Heat ageing 5.13 Long term ageing, 3 000 h X 5.14 Short-term ageing, 240 h X X 5.15 Thermal ove
42、rload X X 5.16 Shrinkage by heat X X Resistance to chemicals 5.17 Fluid compatibility X f,g X f,g ISO 2013 All rights reserved 3BS ISO 6722-2:2013ISO 6722-2:2013(E) Subclause Test description Mandatory If required c In-process a Initial Periodic b Initial Periodic b 5.18 Durability of cable marking
43、X g X g 5.19 Resistance to ozone X g 5.20 Resistance to hot water X g 5.21 Temperature and humidity cycling X g 5.22 Resistance to flame propagation X X X applicable test not applicable aA test made on entire cable length during or after manufacture. bThe frequency of periodic testing shall be estab
44、lished by the agreement between the customer and the supplier. cThe usage of “if required” tests shall be established by the agreement between the customer and the supplier. dSome cables are rated at 60 V and others at 600 V. See ISO 6722-1 for details. eSee ISO 6722-1 for details. fSome fluids are
45、for “certification” and others are “if required”. See ISO 6722-1 for details. gCompliance for a cable family may be demonstrated by testing the examples of large and small conduc- tor sizes only (see 4.7). 4.7 Representative conductor sizes for testing When a test is required, all combinations of co
46、nductor size, wall thickness, and insulation formulation shall meet the appropriate requirements. However, if the testing of representative conductor sizes is permitted (see Table 3), compliance for a cable family may be demonstrated by testing the examples of large and small conductor sizes only. P
47、ermission to show compliance for a cable family by testing “representative conductor sizes” shall be established by the agreement between the customer and the supplier. 4.8 Recommended colours For a list of recommended colours, see ISO 6722-1. 5 Tests 5.1 Outside cable diameter 5.1.1 Purpose, test s
48、ample, and test ISO 6722-1 applies. 5.1.2 Requirement No single value shall be larger than the appropriate values specified in Table 4. NOTE See Table A.2 for the minimum outside cable diameters.Table 3 (continued) 4 ISO 2013 All rights reservedBS ISO 6722-2:2013ISO 6722-2:2013(E) 5.2 Insulation thi
49、ckness 5.2.1 Purpose, test sample, and test ISO 6722-1 applies. 5.2.2 Requirement No single value shall be less than the appropriate minimum insulation thickness specified in Table 4. Table 4 Dimensions ISO conductor a Thick wall Thin wall Ultrathin wall Size mm 2 Diameter mm Insulation thickness mm Outside cable diameter mm Insulatio