欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM F457-04(2017) Standard Test Method for Speed and Distance Calibration of Fifth Wheel Equipped With Either Analog or Digital Instrumentation.pdf

    • 资源ID:388339       资源大小:76.62KB        全文页数:4页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM F457-04(2017) Standard Test Method for Speed and Distance Calibration of Fifth Wheel Equipped With Either Analog or Digital Instrumentation.pdf

    1、Designation: F457 04 (Reapproved 2017)Standard Test Method forSpeed and Distance Calibration of Fifth Wheel EquippedWith Either Analog or Digital Instrumentation1This standard is issued under the fixed designation F457; the number immediately following the designation indicates the year of originala

    2、doption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of vehiclespeed and cumulative

    3、distance traveled using a device termeda fifth wheel and using appropriate associated instrumentation.1.2 This test method also describes the calibration techniqueapplicable to digital or analog speed and distance measurementsystems employing a fifth wheel.1.3 The values stated in SI (millimetre-kil

    4、ogram) units areto be regarded as the standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regu

    5、latory limitations prior to use. For specificprecautionary statements, see Section 7.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Gu

    6、ides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2F538 Terminology Relating to the Characteristics and Per-formance of TiresF1082 Practice for TiresDetermining Precision for TestMethod Standards (Wit

    7、hdrawn 2005)33. Terminology3.1 Refer to Terminology F538.4. Summary of Test Method4.1 Vehicle speed and distance determinations are made byuse of a fifth wheel, signal transducer(s), and compatibledisplay devices.4.2 The fifth wheel assembly and signal transducer(s) areattached to the vehicle or the

    8、 test trailer so that the fifth wheelremains in contact with the normal roadway surface while theequipment is in motion. The rotation of this wheel is detectedin a suitable manner and is translated into measurements ofvehicle speed and distance with auxiliary equipment.4.3 The speed is to be communi

    9、cated to the vehicle operatorat all times, and should be visible without undue distraction ora requirement for physical movement on the part of theoperator.4.4 Fifth wheel calibration is performed by operating thedevice at a fixed speed over a known distance and comparingthe speed and distance reado

    10、ut to a known speed and distance.5. Significance and Use5.1 This test method may be used for calibration of speedand distance measurement systems used on tire test vehiclesand tire test trailers, or any land-based vehicle that contacts theroad and that uses a trailing-wheel system for measurement of

    11、speed and distance. This test method applies only to hard, dry,smooth surfaces and is not accurate for highly curved vehiclepaths. This test method does not encompass optical types ofdevices.6. Apparatus6.1 Fifth WheelThe fifth-wheel assembly shall be ofsufficient mechanical integrity to withstand l

    12、ong periods ofsustained operation with minimal maintenance. The wheelvertical pivot assembly shall be sufficient to permit directionalchanges without inducing lateral skidding of the fifth-wheeltire. The fifth-wheel assembly shall be equipped with asuspension capable of minimizing bounce and wheel h

    13、op, dueto roadway irregularities, to the extent necessary to ensuremeasurement accuracy. The wheel shall be equipped with asuitable tire, preferably of a straight-ribbed design. The tiresshall have a minimum (new) size of 34937 (16 138). Tireand wheel shall be balanced statically each time the tire

    14、isreplaced.1This test method is under the jurisdiction of ASTM Committee F09 on Tiresand is the direct responsibility of Subcommittee F09.10 on Equipment, Facilitiesand Calibration.Current edition approved May 1, 2017. Published July 2017. Originally approvedin 1976. Last previous edition approved i

    15、n 2010 as F457 04 (2010). DOI:10.1520/F0457-04R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last a

    16、pproved version of this historical standard is referenced onwww.astm.org.This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommend

    17、ations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.16.2 InstrumentationFifth-wheel systems shall be equippedwith either analog or digital instrumentation for determiningwheel rotation. Suitable readouts shall be provided.6.2.1 Analog Instrumentation:6.2.1.1 Gen

    18、erator (tachometer)The generator shall becoupled to the fifth wheel to produce an electrical outputproportional to the angular velocity (converted into linearvelocity expressed in km/h (mph) of the fifth wheel. Thegenerator output shall be continuously proportional to therotational velocity within t

    19、he required tolerance. The generatoroutput shall be biased after engineering unit conversion by anamount less than or equal to 0.5 % of the converted speed, or0.3 km/h (0.2 mph), whichever is greater. The generatorresponse to changes in speed shall not exceed 0.5 s throughput.Generator operation sha

    20、ll not be degraded by direct or con-densed moisture, road film, petroleum residue, dust, salt, orother environmental contaminates and ambient temperatureextremes.6.2.1.2 Speed ReadoutThe display shall measure the gen-erator output and display the output as kilometres per hour(miles per hour). The ge

    21、nerator output readout shall beequipped with a low pass active filter that will reduce the rippleoutput of the generator to less than or equal to 1 % of themeasured signal or 0.8 km/h (0.5 mph) peak to peak, which-ever is greater. The maximum propagation delay of thefilter/readout combination shall

    22、not exceed 0.5 s. The readoutshall be biased to an amount less than or equal to 1.0 % of thetrue speed, 0.5 km/h (0.3 mph), whichever is greater.6.2.1.3 Distance ReadoutThe distance measuring deviceshall consist of a counter actuated by the fifth wheel with anoutput of at least 31 counts per metre (

    23、10 counts per foot).Distance traveled is calculated by multiplying the distance perpulse by the number of pulses indicated. The count shall berestorable to zero and possess sufficient digit capacity tominimize the need for recycling the count during testing. Theanalog integration of an electrical ge

    24、nerator signal to yield adistance measurement is not recommended. The distancemeasuring device shall have a capability of a resolution of 8 cm(3 in.).6.2.2 Digital Instrumentation:6.2.2.1 TransducerThe digital transducer shall produce aperiodic electrical signal whose period is some integer fraction

    25、of the revolution rate of the fifth wheel, and there shall be aminimum of ten signal counts per 0.3 m (1 ft) of travel of thefifth wheel along the vehicle path. The transducer shall becapable of providing the periodic electrical signals at speedsfrom zero to the maximum speed necessary for the test

    26、beingconducted. Transducer operation shall not be degraded bydirect or condensed moisture, road film, petroleum residue,dust, salt, or other environmental contaminates and ambienttemperature extremes.6.2.2.2 Distance ReadoutThe distance display presentedto the operator shall consist of a digital num

    27、ber representingthe distance traveled. The use of analog integration is notrecommended unless equipment adjustments can be main-tained within the tolerances stated below, over the expectedambient temperature range. The distance measuring deviceshall have a capability of a resolution of 0.076 6 0.038

    28、 m (0.256 0.125 ft).6.2.2.3 Speed ReadoutThe speed display device shallconsist of a digital number. The use of analog integration orsuccessive approximation techniques of speed determination,or both, are not recommended unless equipment adjustmentscan be maintained within tolerances stated below, ov

    29、er theexpected temperature range of the instrumentation environ-ment. The speed readout displays shall be communicated to thevehicle operator at all times without causing undue distractionsor requiring physical movement on the part of the operator. Theminimum increment of the digital speed readout s

    30、hall be 1km/h, if the readout displays in km/h, or 1 mph, if the readoutdisplays in mph.6.3 Tire Pressure, to be accurate to 3 kPa (0.5 psi).6.4 Stopwatch (required only for analog instrumented fifthwheel).7. Safety Precautions7.1 Fifth-wheel assemblies shall be inspected periodically toassure secur

    31、ity of attachment. A safety chain is recommendedto prevent loss under extreme operating conditions. Wheelassemblies should not be subjected to undue side forces, orother conditions that may either impair accuracy or present ahazard to adjacent vehicles.8. Calibration Procedure8.1 Since analog instru

    32、mentation measures fifth-wheel an-gular velocity and digital instrumentation measures angulardisplacement, follow different calibration procedures for eachsystem. In either case, accomplish calibration by adjustmentsof electronics rather than tire pressure or other mechanicalmeans. Adjustment of tir

    33、e pressure may affect the dynamics ofthe fifth-wheel suspension and may disrupt optimum tire-roadcontact. However, small tire inflation pressure changes lessthan 5 psi may be used for small recalibration adjustments.8.2 Fifth-Wheel Preparation:8.2.1 Install the fifth wheel according to the manufactu

    34、rersinstructions and as near as possible to the mid-track position ofthe vehicle.8.2.2 Adjust the fifth-wheel tire pressure to the manufactur-ers specification.8.2.3 It is common practice that the fifth wheel be preparedfor testing by running at least 8 km (5 miles) at approximately64 km/h (40 mph)

    35、immediately before use. Normal travel inpreparation for calibration fulfills this requirement.8.3 Analog CalibrationThe ultimate accuracy of speedmeasurements is determined principally by the accuracy towhich the speed per volt or current calibration can be estab-lished and how constant this calibra

    36、tion remains over the rangeof speed and over time. The accuracy of the distance measure-ment is dependent primarily upon the accuracy to which thedistance traveled per revolution of the fifth wheel can bedetermined. The number of fifth wheel revolutions should bedeterminable to 60.1 revolution in 0.

    37、8-km (0.5-mile) distance,measured using a device whose calibration is traceable to theF457 04 (2017)2National Institute of Standards and Technology (NIST). Thiscalibration should be accomplished by adjustments of electron-ics rather than tire pressure or other mechanical means.Adjustment of tire pre

    38、ssure may affect the dynamics of the fifthwheel suspension and may disrupt optimum tire-road contact.However, tire pressure changes of less than 34 kPa (5 psi) maybe used for recalibration. Initial and final tire pressure shouldbe recorded for future reference and calibration verification.8.3.1 Spee

    39、d Calibration:8.3.1.1 Prepare the fifth wheel in accordance with 8.2.8.3.1.2 Adjust the speed indicator and graphic recordermeter, if necessary, to zero while the vehicle is stationary.8.3.1.3 For analog systems, drive the test vehicle at aconstant speed, 60.8 km/h (0.5 mph), along a straight testco

    40、urse of at least 0.8 km (0.5 miles) measured using a devicewhose calibration is traceable to the National Institute ofStandards and Technology (NIST), at the speed(s) at which tiretests are to be conducted. Measure the time(s) required totraverse this distance with a stopwatch, record fifth wheelout

    41、put, and compute vehicle speed(s). For digital systems,drive the test vehicle in accordance with 8.4.1 through a trap ofcalibrated distance of at least 0.8 km (0.5 miles) measuredusing a device whose calibration is traceable to the NationalInstitute of Standards and Technology (NIST). Record thenumb

    42、er of counts for the distance and repeat four times.Average the runs and compute the number of pulses per secondat 1 km/h if the calibration is being performed in km/h, or 1mph if the calibration is being performed in mph. Using afrequency generator monitored by a frequency counter, input afrequency

    43、 equivalent to the highest speed expected duringtesting. Adjust the output of the readout or signal conditionerfor engineering conversion to an easily readable display.Repeat this for several (at least five) different frequenciesthrough the range expected during the test. Record the resultsfor futur

    44、e reference and calibration verification.8.3.1.4 If the speed readout and recorder are not equal to thecomputed speed to within 60.5 km/h (0.3 mph), adjust eitherthe recorder gain or meter gain, or both, to achieve correspon-dence. Repeat 8.3.1.3 until this requirement is met.8.3.1.5 Following compl

    45、iance with the accuracy require-ment of 8.3.1.4, four additional test runs shall be made (two ineach direction). Compliance with 8.3.1.4 in all four runs shallconstitute a satisfactory speed calibration if the data repeats to60.8 km/h (60.5 mph) or to 1 % of the speed to be used forthe tests, whiche

    46、ver is greater.8.3.2 Distance Calibration:8.3.2.1 Paragraphs 8.2.1 8.2.3 should be followed if thespeed calibration was not performed.8.3.2.2 Position the test vehicle at one end of a test course ofat least 0.8-km (0.5-mile) certified length. Record the relativeposition of the vehicle and course beg

    47、inning marker.8.3.2.3 After recording the fifth-wheel revolution counterreading, smoothly accelerate the test vehicle to the tire testingspeed and stop smoothly at the other end of the course with theend marker in the same relative position as at the beginning ofthe course.8.3.2.4 Note the fifth-whe

    48、el revolution counter reading andcalculate the number of revolutions.8.3.2.5 Calculate the distance calibration factor F as fol-lows:F 5Test course lengthNumber of fifth wheel revolutions8.3.2.6 Four such test runs shall be performed (two in eachdirection) with the final calibration factor (F) being

    49、 the averageof the four calculations. Unknown distances may now bemeasured by multiplying the calibration factor (F)bythenumber of fifth-wheel revolutions in the unknown distance.8.4 Digital CalibrationThe ultimate accuracy of digitalspeed and distance measurements is determined principally bythe accuracy to which the distance per pulse is adjusted over acourse of known length. Periodic calibration is required tocompensate for such factors as tire treadwear, tire aging andgrowth, rolling resistance, and temperature at various speeds.This calibration should be accom


    注意事项

    本文(ASTM F457-04(2017) Standard Test Method for Speed and Distance Calibration of Fifth Wheel Equipped With Either Analog or Digital Instrumentation.pdf)为本站会员(吴艺期)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开