1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Aerospace series - Sleeving, heat-shrinkable, for binding, insulation and identificationPart 301: Adhesive lined polyolefin sleevings - Operating temperature - 55 C to 105 C - Product StandardBS EN 4708-301:2018EUROPEAN
2、 STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4708-301 May 2018 ICS 49.060 English Version Aerospace series - Sleeving, heat-shrinkable, for binding, insulation and identification - Part 301: Adhesive lined polyolefin sleevings - Operating temperature - 55 C to 105 C - Product Standard Srie arospatia
3、le - Manchons thermortractables, de jonction, isolement et identification - Partie 301 : Gaine en polyolfine avec revtement dun adhsif - Tempratures dutilisation - 55 C 105 C - Norme de produit Luft- und Raumfahrt - Wrmeschrumpfender Schlauch zur Befestigung, Isolierung und Identifizierung - Teil 30
4、1: Innenbeschichtete Polyolefin-Formteile - Temperaturbereich - 55 C bis 105 C - Produktnorm This European Standard was approved by CEN on 11 September 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the
5、 status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, Frenc
6、h, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,
7、Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
8、Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Me
9、mbers. Ref. No. EN 4708-301:2018 ENational forewordThis British Standard is the UK implementation of EN 4708301:2018.The UK participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this
10、 committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 98715 1ICS 4
11、9.060Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 4708301:20
12、18EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4708-301 May 2018 ICS 49.060 English Version Aerospace series - Sleeving, heat-shrinkable, for binding, insulation and identification - Part 301: Adhesive lined polyolefin sleevings - Operating temperature - 55 C to 105 C - Product Standard Srie
13、 arospatiale - Manchons thermortractables, de jonction, isolement et identification - Partie 301 : Gaine en polyolfine avec revtement dun adhsif - Tempratures dutilisation - 55 C 105 C - Norme de produit Luft- und Raumfahrt - Wrmeschrumpfender Schlauch zur Befestigung, Isolierung und Identifizierung
14、 - Teil 301: Innenbeschichtete Polyolefin-Formteile - Temperaturbereich - 55 C bis 105 C - Produktnorm This European Standard was approved by CEN on 11 September 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European St
15、andard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (Engl
16、ish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium,
17、Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Swi
18、tzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN n
19、ational Members. Ref. No. EN 4708-301:2018 EBS EN 4708301:2018EN 4708-301:2018 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Required characteristics 5 5 Quality assurance 11 6 Designation . 12 7 Labelling and packaging . 12 8 Technical spec
20、ification . 12 BS EN 4708301:2018EN 4708-301:2018 (E) 3 European foreword This document (EN 4708-301:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Associat
21、ion, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement,
22、 at the latest by November 2018, and conflicting national standards shall be withdrawn at the latest by November 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifyin
23、g any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav R
24、epublic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 4708301:2018EN 4708-301:2018 (E) 4 1 Sco
25、pe This document specifies the required characteristics for heat-shrinkable adhesive lined polyolefin sleevings for use in aircraft electrical systems at operating temperatures between 55 C and 105 C. The sleeving consists of an outer layer being of a flexible cross-linked polyolefin. The inner wall
26、 consists of a hot melt adhesive that flows and fuses during the shrinking process to provide a bond that is suitable where an environmental seal is required. These sleevings are normally supplied with internal diameters up to 40 mm for shrink ratios of 3:1 and up to 52 mm for shrink ratios of 4:1.
27、These sleevings are normally supplied in colour black. Sizes or colours other than those specifically listed in this standard may be available as custom items. These items shall be considered to comply with this standard if they comply with the property requirements listed in Table 3 and Table 5 exc
28、ept for dimensions and mass. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the r
29、eferenced document (including any amendments) applies. EN 3909, Aerospace series Test fluids for electrical and optical components and sub-assemblies EN 4708-001, Aerospace series Sleeving, heat-shrinkable, for binding, insulation and identification Part 001: Technical specification EN 6059-304, Aer
30、ospace series Electrical cables, installation Protection sleeve Test methods Part 304: Flammability IEC 60684-1:2011, Flexible insulating sleeving Part 1: Definitions and general requirements 1IEC 60684-2:2005, Flexible insulating sleeving Part 2: Methods of test 1IEC 60757:1983, Code for designatio
31、n of colours 1 ISO 846:1997, Plastics Evaluation of the action of micro-organisms ISO 1817:2005, Rubber, vulcanized Determination of the effect of liquids MIL-PRF-87937, Performance specification: cleaning compound, aerospace equipment 2AMS 1476B:2004, Deodorant, Aircraft Toilet 33 Terms and definit
32、ions For the purposes of this document, the terms and definitions given in IEC 60684-1 apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ 1 Published by: IEC International Commission E
33、lectrotechnique Internationale. http:/www.iec.ch/. 2 Published by: Department of Defense (DoD). http:/www.defenselink.mil/. 3 Published by: SAE National (US) Society of Automotive Engineers. http:/www.sae.org/. BS EN 4708301:2018EN 4708-301:2018 (E) 5 ISO Online browsing platform: available at http:
34、/www.iso.org/obp 4 Required characteristics 4.1 Dimension and mass See Table 1 and Table 2. Table 1 Dimensional and mass requirements shrink ratio 3:1 Size code Internal diameter mm Recovered total wall thickness mm Recovered meltable wall thickness mm Mass per unit length max. g/m Expanded min. Rec
35、overed max. Nominal 3/1 3 1 1,0 0,30 0,5 7,2 4,5/1,5 4,5 1,5 1,0 0,30 0,5 8,3 6/2 6 2 1,0 0,30 0,6 10,9 9/3 9 3 1,4 0,30 0,6 17,7 12/4 12 4 1,8 0,40 0,8 32,7 19/6 19 6 2,2 0,60 0,8 67,3 24/8 24 8 2,5 0,60 1,0 87 40/13 40 13 2,5 0,60 1,0 130,4 Table 2 Dimensional and mass requirements shrink ratio 4:
36、1 Size code Internal diameter mm Recovered total wall thickness mm Recovered meltable wall thickness mm Mass per unit length max. g/m Expanded min. Recovered max. Nominal 4/1 4 1 1,0 0,30 0,5 7,2 8/2 8 2 1,0 0,30 0,5 10,9 12/3 12 3 1,4 0,30 0,6 17,7 16/4 16 4 1,8 0,40 0,8 32,7 24/6 24 6 2,2 0,60 0,8
37、 67,3 32/8 32 8 2,5 0,60 1,0 87 52/13 52 13 2,5 0,60 1,0 130,4 BS EN 4708301:2018EN 4708-301:2018 (E) 6 4.2 Conditions of test Unless otherwise specified, the sleeving shall be shrunk in a forced air circulation oven for (5 1) min. at 200 C 5 C prior to testing. 4.3 Tests See Table 3. BS EN 4708301:
38、2018EN 4708-301:2018 (E) 7 Table 3 Tests (1 of 3) Designation of the test IEC 60684-2 Clause or subclause Requirements Remarks Dimensions 3 internal diameter 3.1.2 Table 1 and Table 2 wall thickness 3.3.2 Table 1 and Table 2 concentricity 3.3.3 expanded Shrink ratio 3:1 60 % min. Shrink ratio 4:1 50
39、 % min. recovered All types 85 % min. Density 4 Not applicable See Clause 38. Heat shock 6 Heat at 200 C 5 C Tensile strength 19.1 and 19.2 7 MPa min. Elongation at break 19.1 and 19.2 150 % min. Longitudinal change 9 Shrink ratio 3:1between +1 % and 15 % Shrink ratio 4:1between +1 % and 20 % Heat t
40、he expanded sleeving at 200 C 5 C for (5 1) min. Bending after heating 13 Not applicable See Clauses 6, 39 and 50. Bending at low temperature 14 No cracks shall be visible Condition at 55 C 3 K. For strips, the mandrel shall be between 15 and 17 times the wall thickness. Full section sleeving is tes
41、ted unfilled and the mandrel shall be between 20 and 22 times the outer diameter. Dimensional stability during storage 16 The dimensions shall be as specified in Table 1 and Table 2 Tensile strength 19.1 and 19.2 9 MPa min. Use a jaw separation rate of 100 mm/min. Below 6,5 mm diameter test as sleev
42、ing, at 6,5 mm diameter and above test as dumb-bells. Elongation at break 19.1 and 19.2 200 % min. Secant modulus at 2 % elongation 19.4 40 MPa min. 175 MPa max. Breakdown voltage 21 Table 5 Volume resistivity 23 at ambient temperature 23.4.2 1011 m min. after damp heat 23.4.4 1010 m min. Flammabili
43、ty EN 6059-304 Method 2 Clause 6.2 Method in accordance EN 6059-304 Test size 10/8 on 10 mm diameter tube Oxygen ndex 27 Not applicable BS EN 4708301:2018EN 4708-301:2018 (E) 8 Table 3 Tests (2 of 3) Designation of the test IEC 60684-2 Clause or subclause Requirements Remarks Corrosion resistance (T
44、ensile strengh and Elongation) 32 Not applicable Copper corrosion 33 Not applicable Colour fastness to light 34 The colour contrast between the exposed and unexposed parts of the specimens shall be equal to or less than that of the fastness standard. Fastness standard No. 5 Resistance to selected fl
45、uids Tensile strength Elongation at break 36 19.1 and 19.2 19.1 and 19.2 7 MPa min. 200 % min. Use the fluids and test temperatures specified in Table 6 Immersion time (24 1) h Thermal endurance 37 Not applicable See Clause 50. Mass per unit length 38 Table 1 and Table 2 Heat ageing Tensile strength
46、 Elongation at break 39 19.1 and 19.2 19.1 and 19.2 7 MPa min. 150 % min. Heat at 150 C 3 C Water absorption 40 0,5 % Total wall Restricted shrinkage Visual 41 Not applicable Colour stability to heat 42 Not applicable Smoke Index 43 Not applicable Toxicity 44 Not applicable Halogen content 45 Not ap
47、plicable Acid gas generation 46 Not applicable Dynamic shear at ambient temperature 51 Not applicable Dynamic shear at elevated temperature 52 Not applicable Dynamic shear after heat shock and heat ageing 53 Not applicable Rolling drum peel to aluminium 54 60N/25 mm Test size 24/8. Condition for (10
48、 1) min. at 150 C 5 C Aluminium rod dynamic shear 55 Not applicable Sealing 56 Not applicable Adhesive T peel strength 57 Not applicable Long term ageing 50 350 N Ageing temperature shall be 105 C 3 C Aluminium rod dynamic shear 55 Test size 24/8 with a rod diameter of 10 mm BS EN 4708301:2018EN 470
49、8-301:2018 (E) 9 Table 3 Tests (3 of 3) Designation of the test IEC 60684-2 Clause or subclause Requirements Remarks Fungus resistance Tensile strength Elongation at break 19.1 and 19.2 19.1 and 19.2 9 MPa min. 200 % min. The test method shall be ISO 846, method B 56 days exposure Shelf life aEN 4708-001 Clause 4.7 The dimensions shall be as specified
