1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Aerospace series - Fluorocarbon rubber (FKM) - Low compressions set - Hardness 60 IRHDBS EN 2796:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2796 August 2018 ICS 49.025.40 English Version Aerospace series -
2、 Fluorocarbon rubber (FKM) - Low compressions set - Hardness 60 IRHD Srie arospatiale - lastomre fluor (FKM) - Faible dformation rmanente aprs compression - Duret 60 DIDC Luft- und Raumfahrt - Fluorocarbon-Elastomer (FKM) -Niedriger Druckverformungsrest - Hrte 60 IRDH This European Standard was appr
3、oved by CEN on 20 November 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nation
4、al standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own languag
5、e and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, H
6、ungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMU
7、NG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2796:2018 ENational forewordThis British Standard is the UK implementation of EN 2796:2018.The UK particip
8、ation in its preparation was entrusted to Technical Committee ACE/65, Non-metallic materials for aerospace purposes.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contrac
9、t. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 52318 2ICS 49.025.40Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the author
10、ity of the Standards Policy and Strategy Committee on 31 August 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 2796:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2796 August 2018 ICS 49.025.40 English Version Aerospace series - Fluorocarbon rubb
11、er (FKM) - Low compressions set - Hardness 60 IRHD Srie arospatiale - lastomre fluor (FKM) - Faible dformation rmanente aprs compression - Duret 60 DIDC Luft- und Raumfahrt - Fluorocarbon-Elastomer (FKM) -Niedriger Druckverformungsrest - Hrte 60 IRDH This European Standard was approved by CEN on 20
12、November 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may b
13、e obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to
14、the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, I
15、reland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Man
16、agement Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2796:2018 EBS EN 2796:2018EN 2796:2018 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Applicat
17、ion of the material 4 4 Properties 4 5 Designation . 6 6 Technical specification . 6 BS EN 2796:2018EN 2796:2018 (E) 3 European foreword This document (EN 2796:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and vote
18、s carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, ei
19、ther by publication of an identical text or by endorsement, at the latest by February 20219, and conflicting national standards shall be withdrawn at the latest by February 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN
20、 shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic,
21、 Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. BS EN
22、 2796:2018EN 2796:2018 (E) 4 1 Scope This European Standard specifies the properties of fluorocarbon rubber (FKM)1), low compression set, hardness 60 IRHD, for aerospace applications. 2 Normative references The following documents are referred to in the text in such a way that some or all of their c
23、ontent constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3207, Aerospace series Rubber compounds Technical specification ISO 1629, Rubber and la
24、tices Nomenclature ISO 1817, Rubber, vulcanized or thermoplastic Determination of the effect of liquids 3 Terms and definitions No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia:
25、 available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp 4 Application of the material 4.1 General The suitability of the material for a specific application shall be determined by complementary tests carried out on the finished product as the proper
26、ties specified in this European Standard are obtained from standard test specimens. 4.2 Typical use Application requiring a resistance to air, hydrocarbon and synthetic oils, fuels at elevated temperature and low compression set properties. 4.3 Temperature range Continuous service: from 20 C to 225
27、C; Intermittent service: from 20 C to 250 C. 5 Properties See Table 1 and Table 2. For qualification, all tests shall be performed. For batch acceptance, those identified “*” shall be performed. 1)Symbol as per ISO 1629. BS EN 2796:2018EN 2796:2018 (E) 5 Table 1 Test methods Line Column 1 2 3 Proper
28、ties Units Requirements 1 Hardness IRHD 60 45+* 2 3 Density Mg/m3a* 4 5 Tensile strength MPa 10 min. * 6 7 Elongation at break % 180 min. * 8 9 Modulus at % strain MPa 10 11 Tear strength N/mm 12 13 Resistance to low temperatures TR10 C 12 max. 14 Crystallization Point 15 Compression set % 15.1 Afte
29、r 70 h to 200 C 25 max. * 15.2 After h to C 16 17 Ozone resistance Ozone concentration : ( ) pphm Elongation of test piece : % Time : h Temperature : C 18 19 Corrosion and adhesion on metals in a dry atmosphere no corrosion no adhesion Time : 168 h Temperature : 200 C 20 Corrosion and adhesion on me
30、tals 20.1 Time : h Temperature : C Humidity : % 20.2 Time : h Temperature : C Humidity : % 30 39 * See Clause 4. aThe value determined for each batch shall not differ from that determined at qualification by more than 0,03 Mg/m3. BS EN 2796:2018EN 2796:2018 (E) 6 Table 2 Tests after exposure to test
31、 media Line Column 1 2 3 4 5 1 Test media Air Liquid B, see ISO 1817 Fluid 101, see ISO 1817 2 Conditions of exposure in test media Units 70 h/250 C 70 h/23 C 70 h/200 C 3 Permitted variation of the properties compared to the initial value Volume % 010+015+4 Mass % 5 max. * 5 Tensile strength % 20 m
32、ax. 6 Elongation at break % 20 max. 7 Hardness IRHD 5 * 5 150* See Clause 4. 6 Designation EXAMPLE 7 Technical specification See EN 3207. BS EN 2796:2018This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other st
33、andards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators
34、and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standard
35、s to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and dow
36、nload PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from
37、our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally
38、 licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof
39、 in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 devi
40、ce provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or i
41、nternal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription produ
42、ct (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go
43、 to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.You can keep in touch with standards developments and receive substantial
44、discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member.PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To f
45、ind out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre availab
46、le, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambigu
47、ity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: BSI Group Headquarters389 Chiswick High Road London W4 4AL UKNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW