1、 Reference number ISO/TR 20573:2006(E) ISO 2006TECHNICAL REPORT ISO/TR 20573 First edition 2006-12-01 Footwear Performance requirements for components for footwear Heels and top pieces Chaussures Exigences de performance pour les composants des chaussures Talons et bonbouts ISO/TR 20573:2006(E) PDF
2、disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, part
3、ies accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative
4、to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 A
5、ll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country
6、 of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reservedISO/TR 20573:2006(E) ISO 2006 All rights reserved iii Foreword ISO (the International
7、 Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been est
8、ablished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardiz
9、ation. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voti
10、ng. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. In exceptional circumstances, when a technical committee has collected data of a different kind from that which is normally published as an International Standard (“state of the art”,
11、 for example), it may decide by a simple majority vote of its participating members to publish a Technical Report. A Technical Report is entirely informative in nature and does not have to be reviewed until the data it provides are considered to be no longer valid or useful. Attention is drawn to th
12、e possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO/TR 20573 was prepared by Technical Committee ISO/TC 216, Footwear. TECHNICAL REPORT ISO/TR 20573:2006(E) ISO 2006 All rig
13、hts reserved 1 Footwear Performance requirements for components for footwear Heels and top pieces 1 Scope This Technical Report establishes the performance requirements for heel and top piece components for footwear (not for finished footwear), irrespective of the material, in order to assess the su
14、itability for the end use and/or fitness for purpose. It also establishes the test methods used to evaluate the compliance with the requirements. This Technical Report applies to heel and top piece for all kind of footwear as defined in Clause 3. This Technical Report is intended to be used as a ref
15、erence between the manufacturer and the supplier. It is not intended for third party certification of finished footwear intended for the consumer. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition
16、cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 31-0, Quantities and units Part 0: General Principles EN 12770, Footwear Test methods for outsoles Abrasion resistance EN 13287, Personal protective equipment Footwear Test me
17、thod for slip resistance EN 13400, Footwear. Sampling location, preparation and duration of conditioning of samples and test pieces EN/ISO 19952, Footwear Vocabulary EN/ISO 19953, Footwear Test methods for heels Resistance to lateral impact EN/ISO 19956, Footwear Test methods for heels Fatigue resis
18、tance EN/ISO 19957, Footwear Test methods for heels Heel pin holding strength EN/ISO 19958, Footwear Test methods for heels and top pieces Top piece retention strength 3 Terms and definitions For the purposes of this document, the terms and definitions in EN/ISO 19952 apply. ISO/TR 20573:2006(E) 2 I
19、SO 2006 All rights reserved4 Requirements 4.1 General This Technical Report establishes two different types of performance requirement. The essential requirements shall all be taken into account. The additional ones can be additionally agreed upon by the component supplier and the footwear manufactu
20、rer as indicated in 4.2 to 4.10. The results of each single analytical determination, as well as the average values, shall be rounded off in accordance with ISO 31-0. When taken from finished footwear, samples shall be prepared in accordance with EN 13400. 4.2 Performance requirements for heel and t
21、op piece components for general purpose sports and leisure footwear 4.2.1 Essential requirements for heel Test method Property Requirement EN/ISO 19957 Heel pin holding strength W 80 N/mm EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall be carried out using
22、ceramic tiles (floor), water and detergent (lubricant) 4.2.2 Essential requirements for top pieces Test method Property Requirement EN 12770 Abrasion resistance Density (d) W 0,9 g/cm 3 d 0,9 g/cm 3u 150 mm 3u 120 mg EN/ISO 19958 Top piece retention strength W 150 N Testing shall be carried out with
23、 the appropriate spike fitting EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall be carried out using ceramic tiles (floor), water and detergent (lubricant) ISO/TR 20573:2006(E) ISO 2006 All rights reserved 3 4.2.3 Additional requirements for heels 1 )Subclau
24、se Test method Property Requirement 4.2.3.1 EN/ISO 19956 Fatigue resistance W 14 000 blows 4.2.3.2 EN/ISO 19953 Resistance to lateral impact W 5 J 4.3 Performance requirements for heel and top piece components for school footwear 4.3.1 Essential requirements for heel Test method Property Requirement
25、 EN/ISO 19957 Heel pin holding strength W 70 N/mm EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall be carried out using ceramic tiles (floor), water and detergent (lubricant) 4.3.2 Essential requirements for top pieces Test method Property Requirement EN 127
26、70 Abrasion resistance d W 0,9 g/cm 3 d 0,9 g/cm 3u 200 mm 3u 150 mg EN/ISO 19958 Top piece retention strength W 140 N Testing shall be carried out with the appropriate spike fitting EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall be carried out using ceram
27、ic tiles (floor), water and detergent (lubricant) 1) These characteristics are essential if the widest part of the heel is less than 30 mm. ISO/TR 20573:2006(E) 4 ISO 2006 All rights reserved4.4 Performance requirements for heel and top piece components for casual footwear 4.4.1 Essential requiremen
28、ts for heel Test method Property Requirement EN/ISO 19957 Heel pin holding strength W 80 N/mm EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall be carried out using ceramic tiles (floor), water and detergent (lubricant) 4.4.2 Essential requirements for top pi
29、eces Test method Property Requirement EN 12770 Abrasion resistance d W 0,9 g/cm 3d 0,9 g/cm 3u 150 mm 3u 120 mg EN/ISO 19958 Top piece retention strength W 150 N Testing shall be carried out with the appropriate spike fitting EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cas
30、es testing shall be carried out using ceramic tiles (floor), water and detergent (lubricant) 4.4.3 Additional requirements for heels 1)Subclause Test method Property Requirement 4.4.3.1 EN/ISO 19956 Fatigue resistance W 14 000 blows 4.4.3.2 EN/ISO 19953 Resistance to lateral impact W 5 J 4.5 Perform
31、ance requirements for heel and top piece components for mens town footwear 4.5.1 Essential requirements for heel Test method Property Requirement EN/ISO 19957 Heel pin holding strength W 80 N/mm EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall be carried out
32、 using ceramic tiles (floor), water and detergent (lubricant) ISO/TR 20573:2006(E) ISO 2006 All rights reserved 5 4.5.2 Essential requirements for top pieces Test method Property Requirement EN 12770 Abrasion resistance d W 0,9 g/cm 3 d 0,9 g/cm 3u 200 mm 3u 150 mg EN/ISO 19958 Top piece retention s
33、trength W 140 N Testing shall be carried out with the appropriate spike fitting EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall be carried out using ceramic tiles (floor), water and detergent (lubricant) 4.5.3 Additional requirements for heels 1)Subclause T
34、est method Property Requirement 4.5.3.1 EN/ISO 19956 Fatigue resistance W 15 000 blows 4.5.3.2 EN/ISO 19953 Resistance to lateral impact W 5 J 4.6 Performance requirements for heel and top piece components for cold weather footwear 4.6.1 Essential requirements for heel Test method Property Requireme
35、nt EN/ISO 19957 Heel pin holding strength W 80 N/mm EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall be carried out using ceramic tiles (floor), water and detergent (lubricant) ISO/TR 20573:2006(E) 6 ISO 2006 All rights reserved4.6.2 Essential requirements f
36、or top pieces Test method Property Requirement EN 12770 Abrasion resistance d W 0,9 g/cm 3d 0,9 g/cm 3u 200 mm 3u 150 mg EN/ISO 19958 Top piece retention strength W 140 N Testing shall be carried out with the appropriate spike fitting EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In
37、 both cases testing shall be carried out using ceramic tiles (floor), water and detergent (lubricant) 4.6.3 Additional requirements for heels 1)Subclause Test method Property Requirement 4.5.3.1 EN/ISO 19956 Fatigue resistance W 15 000 blows 4.5.3.2 EN/ISO 19953 Resistance to lateral impact W 5 J 4.
38、7 Performance requirements for heels and top pieces components for womens town footwear 4.7.1 Essential requirements for heel Test method Property Requirement EN/ISO 19957 Heel pin holding strength W 80 N/mm EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall b
39、e carried out using ceramic tiles (floor), water and detergent (lubricant) ISO/TR 20573:2006(E) ISO 2006 All rights reserved 7 4.7.2 Essential requirements for top pieces Test method Property Requirement EN 12770 Abrasion resistance d W 0,9 g/cm 3d 0,9 g/cm 3u 250 mm 3u 170 mg EN/ISO 19958 Top piece
40、 retention strength W 120 N Testing shall be carried out with the appropriate spike fitting EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall be carried out using ceramic tiles (floor), water and detergent (lubricant) 4.7.3 Additional requirements for heels 1
41、)Subclause Test method Property Requirement 4.7.3.1 EN/ISO 19956 Fatigue resistance W 14 000 blows 4.7.3.2 EN/ISO 19953 Resistance to lateral impact W 5 J 4.8 Performance requirements for heel and top piece components for fashion footwear 4.8.1 Essential requirements for heel Test method Property Re
42、quirement EN/ISO 19957 Heel pin holding strength W 80 N/mm EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel slip) In both cases testing shall be carried out using ceramic tiles (floor), water and detergent (lubricant) ISO/TR 20573:2006(E) 8 ISO 2006 All rights reserved4.8.2 Essential require
43、ments for top pieces Test method Property Requirement EN 12770 Abrasion resistance d W 0,9 g/cm 3d 0,9 g/cm 3u 300 mm 3u 250 mg EN/ISO 19958 Top piece retention strength W 120 N Testing shall be carried out with the appropriate spike fitting EN 13287 Slip resistance W 0,30 (flat slip) W 0,28 (heel s
44、lip) In both cases testing shall be carried out using ceramic tiles (floor), water and detergent (lubricant) 4.8.3 Additional requirements for heels 1)Subclause Test method Property Requirement 4.7.3.1 EN/ISO 19956 Fatigue resistance W 14 000 blows 4.7.3.2 EN/ISO 19953 Resistance to lateral impact W
45、 5 J 4.9 Performance requirements for heel and top pieces component for infants footwear No performance requirements currently defined. 4.10 Performance requirements for heel and top piece components for indoor footwear No performance requirements currently defined. ISO/TR 20573:2006(E) ISO 2006 All
46、 rights reserved 9 5 Marking and labelling Marking and labelling is optional. If reference to this Technical Report is made, only heels and top pieces complying with all the essential requirements can be marked. In this case, these shall be clearly marked by the manufacturer either directly on the p
47、roduct or by a label with the following additional information: a) The manufacturers name, trade mark or identification mark. b) The type of footwear for which the heel or top piece shall be used as indicated as follows: Type of footwear Code General sports footwear SP School footwear SC Casual foot
48、wear CS Men town footwear MT Cold weather footwear CW Women town footwear WT Fashion footwear FS Infants footwear IF Indoor footwear IN c) Reference to this Technical Report, i.e., ISO/TR 25073. d) If the component complies with additional requirements agreed upon between the component supplier and
49、the footwear manufacturer, it may be specified on the marking or label, making reference to the corresponding subclause. Any reference to compliance with this Technical Report shall not be put in a part of the heel or top piece which could be visible when the footwear is finished. ISO/TR 20573:2006(E) ICS 61.060 Price based on 9 pages ISO 2006 All rights reserved
