1、 Reference number ISO/IEC 20114:2004(E) ISO/IEC 2004INTERNATIONAL STANDARD ISO/IEC 20114 First edition 2004-05-15 Information technology Telecommunications and information exchange between systems Private Integrated Services Network (PISN) Inter-exchange signalling protocol Make call request supplem
2、entary service Technologies de linformation Tlcommunications et change dinformation entre systmes Rseau priv intgration de services Protocole de signalisation dchange Service supplmentaire de demande par appel ISO/IEC 20114:2004(E) PDF disclaimer This PDF file may contain embedded typefaces. In acco
3、rdance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes l
4、icensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for prin
5、ting. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO/IEC 2004 All rights reserved. Unless otherwise specified, no part of t
6、his publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1
7、211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2004 All rights reservedISO/IEC 20114:2004(E) ISO/IEC 2004 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope 1 2 Conformance. 1 3 Normative ref
8、erences. 1 4 Terms and definitions. 2 4.1 External definitions. 2 4.2 Other definitions. 3 5 Acronyms. 4 6 Signalling Protocol for the support of SS-MCR.4 6.1 SS-MCR description 4 6.2 SS-MCR operational requirements 4 6.3 SS-MCR coding requirements . 6 6.4 SS-MCR state definitions . 9 6.5 SS-MCR sig
9、nalling procedures . 10 6.6 SS-MCR impact of interworking with public ISDNs. 13 6.7 SS-MCR impact of interworking with non-ISDNs 13 6.8 Protocol interactions between SS-MCR and other supplementary services and ANFs 13 6.9 SS-MCR parameter values (Timers) 16 Annex A (normative) Protocol Implementatio
10、n Conformance Statement (PICS) Proforma . 17 A.1 Introduction. 17 A.2 Instructions for completing the PICS proforma.17 A.3 PICS proforma for ISO/IEC 20114 18 Annex B (informative) Examples of Message Sequences 21 B.1 Example message sequences for invocation and operation of SS-MCR 22 Annex C (inform
11、ative) Specification and Description Language (SDL) Representation of Procedures 26 C.1 SDL representation of SS-MCR at the Requesting PINX 27 C.2 SDL representation of SS-MCR at the Co-operating PINX 28 C.3 SDL representation of SS-MCR at the Destination PINX 29 ISO/IEC 20114:2004(E) iv ISO/IEC 200
12、4 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Sta
13、ndards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO an
14、d IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee
15、 is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the po
16、ssibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 20114 was prepared by ECMA (as ECMA-344) and was adopted, under a special “fast-track procedure”, by Joint Techni
17、cal Committee ISO/IEC JTC 1, Information technology, in parallel with its approval by national bodies of ISO and IEC. ISO/IEC 20114:2004(E) ISO/IEC 2004 All rights reserved vIntroduction This International Standard is one of a series defining services and signalling protocols applicable to Private I
18、ntegrated Services Networks (PISNs). The series uses ISDN concepts as developed by ITU-T and conforms to the framework of International Standards for Open Systems Interconnection as defined by ISO/IEC. This International Standard specifies the signalling protocol for use at the Q reference point in
19、support of the Make Call Request supplementary service. The protocol defined in this International Standard forms part of the PSS1 protocol (informally known as QSIG). This International Standard is based upon the practical experience of ECMA member companies and the results of their active and cont
20、inuous participation in the work of ISO/IEC JTC1, ITU-T, ETSI and other international and national standardization bodies. It represents a pragmatic and widely based consensus. INTERNATIONAL STANDARD ISO/IEC 20114:2004(E) ISO/IEC 2004 All rights reserved 1Information technology Telecommunications an
21、d information exchange between systems Private Integrated Services Network (PISN) Inter-exchange signalling protocol Make call request supplementary service 1 Scope This International Standard specifies the signalling protocol for the support of the Make Call Request supplementary service (SS-MCR) a
22、t the Q reference point between Private Integrated services Network eXchanges (PINXs) connected together within a Private Integrated Services Network (PISN). Supplementary service MCR enables a Requesting User to request a Co-operating User to establish a new Requested Call to a Destination User. Th
23、is new Requested Call between the Co-operating and Destination User can be either a Basic call or a Call Independent Signalling Connection. The Q reference point is defined in ISO/IEC 11579-1. Service specifications are produced in three stages and according to the method specified in ETS 300 387. T
24、his International Standard contains the stage 3 specification for the Q reference point and satisfies the requirements identified by the stage 1 and stage 2 specifications in ISO/IEC 20113. The signalling protocol for SS-MCR operates on top of the signalling protocol for basic circuit switched call
25、control, as specified in ISO/IEC 11572, and uses certain aspects of the generic procedures for the control of supplementary services specified in ISO/IEC 11582. This International Standard also specifies additional signalling protocol requirements for the support of interactions at the Q reference p
26、oint between SS-MCR and other supplementary services and ANFs. This International Standard is applicable to PINXs, which can interconnect to form a PISN. 2 Conformance In order to conform to this International Standard, a PINX shall satisfy the requirements identified in the Protocol Implementation
27、Conformance Statement (PICS) proforma in Annex A. Conformance to this International Standard includes conforming to those clauses that specify protocol interactions between SS-MCR and other supplementary services and ANFs for which signalling protocols at the Q reference point are supported in accor
28、dance with the stage 3 standards concerned. 3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any ame
29、ndments) applies. ISO/IEC 20114:2004(E) 2 ISO/IEC 2004 All rights reservedISO/IEC 11572:2000, Information technology Telecommunications and information exchange between systems Private Integrated Services Network Circuit mode bearer services Inter-exchange signalling procedures and protocol ISO/IEC
30、11579-1:1994, Information technology Telecommunications and information exchange between systems Private integrated services network Part 1: Reference configuration for PISN Exchanges (PINX) ISO/IEC 11582:2002, Information technology Telecommunications and information exchange between systems Privat
31、e Integrated Services Network Generic functional protocol for the support of supplementary services Inter-exchange signalling procedures and protocol ISO/IEC 20113:2004, Information technology Telecommunications and information exchange between systems Private Integrated Services Network Specificati
32、on, functional model and information flows Make call request supplementary service ISO/IEC 20115:2004, Information technology Telecommunications and information exchange between systems Private Integrated Services Network Use of QSIG for Message Centre Access (MCA) profile standard ETS 300 387:1994,
33、 Private Telecommunication Network (PTN); Method for the specification of basic and supplementary services ITU-T Rec. I.112:1993, Vocabulary of terms for ISDNs ITU-T Rec. I.210:1993, Principles of telecommunication services supported by an ISDN and the means to describe them ITU-T Rec. Q.950:2000, D
34、igital Subscriber Signalling System No. 1 (DSS 1) Supplementary services protocols, structure and general principles ITU-T Rec. Z.100:1999, Specification and Description Language 4 Terms and definitions For the purposes of this document, the following terms and definitions apply. 4.1 External defini
35、tions This International Standard uses the following terms defined in other documents: Application Protocol Data Unit (APDU) (ISO/IEC 11582) Call, Basic call (ISO/IEC 11582) Call Independent Signalling Connection (ISO/IEC 11582) Call-Independent (ISO/IEC 11582) Gateway PINX (ISO/IEC 11582) Originati
36、ng PINX (ISO/IEC 11582) Private Integrated Services Network (PISN) (ISO/IEC 11579-1) Private Integrated services Network eXchange (PINX) (ISO/IEC 11579-1) Signalling (ITU-T Rec. I.112) ISO/IEC 20114:2004(E) ISO/IEC 2004 All rights reserved 3 Supplementary Service (ITU-T Rec. I.210) Supplementary Ser
37、vice Control Entity (ISO/IEC 11582) Terminating PINX (ISO/IEC 11582) Transit PINX (ISO/IEC 11582) 4.2 Other definitions 4.2.1 Co-operating PINX The PINX where the Co-operating User is located. 4.2.2 Co-operating User The user who receives a Make Call Request and who shall set up a new Requested Call
38、 to the Destination User. 4.2.3 Destination PINX The PINX where the Destination User is located. 4.2.4 Destination User The called user of the Requested Call i.e. the user to whom the Co-operating User shall establish a Requested Call. 4.2.5 Make Call Request A request from the Requesting User for a
39、 new call (i.e. Requested Call) between a Co-operating User and a Destination User. 4.2.6 Original Call The call between the Requesting User and the Co-operating User. The Original Call can be either a Basic call or a Call Independent Signalling Connection and is correlated with the Requested Call.
40、4.2.7 Requested Call The call between the Co-operating User and the Destination User that is established by the Co-operating User due to a Make Call Request from the Requesting User. The Requested Call can either be a Basic call (with a specific Basic Service) or a Call Independent Signalling Connec
41、tion and is correlated with the Original Call. 4.2.8 Requesting PINX The PINX where the Requesting User is located. 4.2.9 Requesting User The User who sends a Make Call Request to the Co-operating User with the request to establish a specific Requested Call to the Destination User. ISO/IEC 20114:200
42、4(E) 4 ISO/IEC 2004 All rights reserved5 Acronyms ANF Additional Network Feature APDU Application Protocol Data Unit ASN.1 Abstract Syntax Notation One CISC Call Independent Signalling Connection ISDN Integrated Services Digital Network NFE Network Facility Extension PICS Protocol Implementation Con
43、formance Statement PINX Private Integrated services Network eXchange PISN Private Integrated Services Network SDL Specification and Description Language SS Supplementary Service SS-MCR Supplementary Service Make Call Request 6 Signalling Protocol for the support of SS-MCR 6.1 SS-MCR description The
44、supplementary service MCR enables a Requesting User to request a Co-operating User to establish a new Requested Call to a Destination User. This new Requested Call between the Co-operating User and the Destination User can either be a Basic call or a Call Independent Signalling Connection. The new R
45、equested Call is correlated to the Original Call between the Requesting and Co-operating User. 6.2 SS-MCR operational requirements 6.2.1 Requirements on a Requesting PINX Call establishment procedures for the incoming and outgoing side of an inter-PINX link and call release procedures, as specified
46、in ISO/IEC 11572, shall apply. Generic procedures for call-related control of supplementary services, as specified in ISO/IEC 11582 for an End PINX, shall apply. Generic procedures for the call-independent control (connection-oriented) of supplementary services, as specified in ISO/IEC 11582 for an
47、Originating PINX and for a Terminating PINX, shall apply. 6.2.2 Requirements on a Co-operating PINX Call establishment procedures for the incoming and outgoing side of an inter-PINX link and call release procedures, as specified in ISO/IEC 11572, shall apply. Generic procedures for call-related cont
48、rol of supplementary services, as specified in ISO/IEC 11582 for an End PINX, shall apply. ISO/IEC 20114:2004(E) ISO/IEC 2004 All rights reserved 5Generic procedures for the call-independent control (connection-oriented) of supplementary services, as specified in ISO/IEC 11582 for a Terminating PINX
49、 and for an Originating PINX, shall apply. 6.2.3 Requirements on a Destination PINX Call establishment procedures for the incoming and outgoing side of an inter-PINX link and call release procedures, as specified in ISO/IEC 11572, shall apply. Generic procedures for call-related control of supplementary services, as specified in ISO/IEC 11582 for an End PINX, shall apply. Generic procedures for the call-independent control (connection-oriented) of su
