1、 Reference number ISO 8568:2007(E) ISO 2007INTERNATIONAL STANDARD ISO 8568 Second edition 2007-07-01 Mechanical shock Testing machines Characteristics and performance Chocs mcaniques Machines dessai Caractristiques et performance ISO 8568:2007(E) PDF disclaimer This PDF file may contain embedded typ
2、efaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infr
3、inging Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were opt
4、imized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved.
5、Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. I
6、SO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reservedISO 8568:2007(E) ISO 2007 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative refer
7、ences . 1 3 Terms and definitions. 2 4 Performance 2 4.1 General. 2 4.2 Operation principles. 2 4.3 Test types 3 4.4 Shock-testing machine components 3 5 Shock-testing machine specification . 4 6 Requirements for shock-testing machines 5 6.1 General. 5 6.2 Safety requirements . 5 6.3 Table or carria
8、ge. 5 6.4 Hoisting or pre-loading 6 6.5 Braking systems . 6 6.6 Reaction mass. 6 6.7 Shock pulse-shaping devices and methods 7 7 Inspection of a shock-testing machine 7 7.1 General. 7 7.2 Preparation procedure . 7 7.3 Example of an inspection procedure for a shock-testing machine operation . 8 Annex
9、 A (informative) Devices for shaping various pulse shapes . 10 Annex B (informative) Shock-response spectra, shock synthesis and analysis 12 Annex C (informative) Use of a vibration generator for producing a shock pulse 15 Annex D (normative) Determination of uniformity of acceleration and relative
10、transverse motion on the table of a shock-testing machine 20 Annex E (normative) Stray magnetic field. 22 Bibliography . 23 ISO 8568:2007(E) iv ISO 2007 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO me
11、mber bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governme
12、ntal and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Dire
13、ctives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bod
14、ies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8568 was prepared by Technical Committee ISO/TC 108, Mechanical vibration, sh
15、ock and condition monitoring, Subcommittee SC 6, Vibration and shock generating systems. This second edition cancels and replaces the first edition (ISO 8568:1989), which has been technically revised. INTERNATIONAL STANDARD ISO 8568:2007(E) ISO 2007 All rights reserved 1 Mechanical shock Testing mac
16、hines Characteristics and performance 1 Scope This International Standard specifies performance parameters and methods of inspection of mechanical shock-testing machines and gives guidelines for describing their characteristics. It is intended to ensure that the potential user of a particular shock-
17、testing machine is provided with an adequate description of the characteristics of the machine, and also to give guidance on the selection of such machines. This International Standard is applicable to the shock-testing machines that are used for demonstrating or evaluating the effect of shock condi
18、tions representative of the service environment in accordance with the relevant part of IEC 60068 and also for diagnostic testing. The purpose of the shock test is to reveal mechanical weakness and/or degradation in specified performance. It can also be used to determine the structural integrity of
19、a test specimen or as a means of quality control. Machines used for simulation of earthquakes, sonic booms, explosions and implosions, bursting tests, metalworking, forming, etc. are not covered in this International Standard. Several techniques for generating the desired shock motion are discussed.
20、 Both simple-pulse and complex transients can be produced. The simulation of transients can be achieved by control of the test with a specified shock-response spectrum. NOTE 1 Annex A gives a description of pulse-shaping devices. Annex B defines methods of application of the shock response spectra.
21、Annex C considers a method of evaluating the possibility of using a vibration generator for producing a shock pulse. Annexes D and E deal with the methods of measurement of some characteristics in inspection methods (or procedures) of shock-testing machines. NOTE 2 Characteristics of vibration-gener
22、ating equipment are covered in ISO 5344, ISO 6070 and ISO 8626. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced documen
23、t (including any amendments) applies. ISO 2041:1990, Vibration and shock Vocabulary ISO 5347 (all parts), Methods for the calibration of vibration and shock pick-ups ISO 5348, Mechanical vibration and shock Mechanical mounting of accelerometers ISO 15261, Vibration and shock generating systems Vocab
24、ulary ISO 16063 (all parts), Methods for the calibration of vibration and shock transducers IEC 60068-1:1988, Environmental testing Part 1: General and guidance IEC 60068-2-27:1987, Environmental testing Part 2: Tests Test Ea and guidance: Shock IEC 60068-2-81, Environmental testing Part 2-81: Tests
25、 Test Ei: Shock Shock response spectrum synthesis ISO 8568:2007(E) 2 ISO 2007 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 2041, ISO 15261 and the following apply. 3.1 check point fixing point nearest to the centre of the table
26、surface of the shock-testing machine, unless there is a fixing point having a more rigid connection to the table, in which case the latter point is used 3.2 nominal load maximum load used for the testing of a shock-testing machine as specified by the manufacturer 3.3 shock-testing machine device for
27、 subjecting a system to controlled and reproducible mechanical shock ISO 2041:1990, 3.23 NOTE Shock-testing machines can be classified as specially designed shock generators, gravity and powered, and vibration generators of electrodynamic and servo-hydraulic types used in a shock mode. 4 Performance
28、 4.1 General The performance of a shock-testing machine is based on a relatively slow accumulation of energy used to reproduce a shock, and its consequent discharge in an energy-transducing device for a short period of time. The energy needed to create a shock may be achieved by the work against gra
29、vity (in free-fall machines) or, if the shock is in a direction other than upwards or if the free-fall machine does not provide enough velocity change, the necessary potential energy may be supplied by elastic cords, springs or hydraulic and pneumatic means. The shock can also be achieved by releasi
30、ng compressed gas, by explosives or by transfer of momentum from one moving mass to another. 4.2 Operation principles According to the principle used, shock-testing machines are classified as free-fall or accelerated shock-testing machines, or as gas guns or explosive guns, hydraulic and pneumatic,
31、as well as servo-hydraulic and electrodynamic. The shock pulse (either a single-pulse or a transient vibration) is produced by a shock pulse-shaping device mounted on the table or carriage, on the reaction mass, or on both. A wide selection of pulse shapes can be produced depending on how the kineti
32、c energy is transferred by pulse-shaping devices. Annex A gives some guidelines on the selection of pulse-shaping devices. Pulse-shaping devices can be used in a rebounding or non-rebounding mode. Usually the device that attaches the test specimen is initially accelerated and a shock is produced dur
33、ing the rebound of the test specimen. Sometimes (for large masses or when the acceleration of the test specimen during shock pre-history is undesirable) a reaction mass or a hammer can be initially accelerated and the shock is produced as a result of the impact between the reaction mass and the devi
34、ce that attaches the test specimen. This mode is classified as non-rebounding. ISO 8568:2007(E) ISO 2007 All rights reserved 3 As an alternative to the shaping of the shock pulse, for electrodynamic or servo-hydraulic vibration generators, a shock-response spectrum of the impulse to be applied to th
35、e specimen may be shaped to be similar to the required shock-response spectrum. When the test specification requires some tolerance for a test shock-response spectrum (e.g. +3 dB, 1,5 dB), electrodynamic and servo-hydraulic test equipment for generating vibration may also be used for shock testing.
36、These machines can generate classical shock waveforms (half-sine, trapezoidal, saw-tooth, etc.) as well as arbitrary waveforms which have the required shock-response spectra, and are usually produced by means of digital control, but generally have limited velocity and displacement capability. A meth
37、od for maintaining the above limitations is briefly treated in Annex C. Characteristics of vibration-generating equipment are covered in ISO 5344, ISO 6070 and ISO 8626. 4.3 Test types 4.3.1 Shock pulse generation Classical shock pulse shapes in accordance with IEC 60068-2-27 are generated with addi
38、tional pre-pulse and post-pulse shaping to limit velocity and displacement. The amplitude of the pre-pulse and post-pulse shapes is limited to a small fraction of the primary pulse amplitude. 4.3.2 Shock-response spectrum generation A brief, low-level oscillatory transient impulse is typically appli
39、ed to the specimen. The shock-response spectrum is measured, compared with the desired shock-response spectrum, and the difference used to modify the shape of the next impulse. Typically, this process is repeated several times until the desired shock spectrum is achieved, and then an input transient
40、 impulse of the desired level is applied to the specimen. The desired shock spectrum may be either standardized (i.e. one of the shock spectra of Annex B) or the shock spectrum of a field environment. 4.4 Shock-testing machine components A shock-testing machine consists of the following: a) a rigid
41、table or carriage with means of attaching test specimens and shock pulse-shaping devices; b) a set of guides that controls the movement of the carriage; c) a means for storing the potential energy necessary for imparting the shock, such as provisions for hoisting or preloading springs and cords atta
42、ched to the carriage; d) a means for securing the carriage at a selected drop height or position, prior to initiation of the shock pulse; e) a release mechanism; f) a reaction mass or base upon which the carriage impacts; g) a pulse-shaping and rebound braking system, or means to generate and contro
43、l the shock spectra; h) control equipment; i) shock-measuring system; j) auxiliary power, cooling and other equipment, as required. ISO 8568:2007(E) 4 ISO 2007 All rights reserved5 Shock-testing machine specification The motion of the table or carriage may be specified by shock-response spectra and/
44、or time-history parameters. Depending on the type of shock-testing machine (specially designed shock generators or vibration generators used in a shock mode), where applicable, data together with tolerances, shall be given for the following items: a) available pulse shapes for free fall and accelera
45、ted tables; b) maximum velocity change; c) maximum displacement; d) range of reproducible shock-pulse peak accelerations versus pulse durations; e) initial or pre-pulse acceleration and final or post-pulse acceleration; f) minimum shock-pulse duration; g) frequency range of wavelets to reproduce a s
46、hock-response spectrum; h) shock-response spectrum flatness with resolution in 1/3, 1/6 or 1/12 octave; i) maximum drop height, preload pressure or charge; j) tare mass of table or carriage and total moving mass; k) maximum allowable axial force of specimen-mounting screw; l) natural frequencies of
47、the table or carriage; m) natural frequencies of the machine on its foundation; n) required pressure and volume of gas and liquids; o) quantities and flow rates of fluid or gas for the operation of the machine; p) type of rebound braking system and braking force; q) size and overall dimensions of th
48、e machine and its parts, especially the table or carriage and its accessories; r) dimensions, mass and mounting method of reaction masses and floor-loading requirements; s) maximum size and mass of test specimen; t) mounting facilities for test specimen and transducers; u) number of shocks (shock pu
49、lses) possible per unit time, or, alternatively, minimum period between two shocks; v) specification of the shock-measuring system employed; w) centre of gravity of the table, plus the effect of any off-centre load; x) acceptable range of environmental conditions, i.e. temperature, humidity, etc. ISO 8568:2007(E) ISO 2007 All rights reserved 5 6 Requirements for shock-testing machines 6.1 General The performance of shock-testing machines shall be defined and specified by the manufacturer. Detailed installation, operat
