1、 ISO 2017 Fire fighting Portable fire extinguishers Performance and construction Lutte contre lincendie Extincteurs portatifs Performances et construction INTERNATIONAL STANDARD ISO 7165 Third edition 2017-07 Reference number ISO 7165:2017(E) ISO 7165:2017(E)ii ISO 2017 All rights reserved COPYRIGHT
2、 PROTECTED DOCUMENT ISO 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, withou
3、t prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.o
4、rg ISO 7165:2017(E)Foreword vi 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Classification of extinguishers . 4 5 Extinguishing media, propellants and filling requirements . 4 5.1 Extinguishing media . 4 5.1.1 Carbon dioxide . 4 5.1.2 Clean agents . 4 5.1.3 Powders . 4 5.1.4 Fo
5、am concentrates . 5 5.1.5 Water-based agents . 5 5.2 Propellants . 5 5.3 Filling requirements . 5 5.3.1 Fill density . 5 5.3.2 Filling tolerance 5 5.3.3 Charges . 5 6 Pressure requirements for low-pressure extinguishers. 6 6.1 Test pressure. 6 6.2 Minimum burst pressure . 6 7 General operating perfo
6、rmance requirements 6 7.1 Operating temperatures 6 7.2 Minimum effective discharge time and bulk range of discharge . 6 7.2.1 Class A-rated extinguishers 6 7.2.2 Class B rated extinguishers . 7 7.2.3 Bulk range 8 7.3 Resistance to temperature changes 9 7.3.1 Requirements . 9 7.3.2 Test method 9 7.4
7、Retention of charge . 9 7.4.1 Routine checks . 9 7.4.2 Retention of charge following partial discharge .10 7.4.3 Long-term leakage test 11 7.5 Mechanical resistance 11 7.5.1 Resistance to impact 11 7.5.2 Resistance to vibrations .12 7.6 Resistance to corrosion 13 7.6.1 External corrosion test 13 7.6
8、.2 Internal corrosion test for extinguishers using water-based media 14 7.7 Tapping test (powder extinguishers only) .14 7.7.1 Requirements 14 7.7.2 Test apparatus .14 7.7.3 Test method .17 7.8 Intermittent discharge test . .18 8 Performance requirements for test fires .18 8.1 Rating suitability for
9、 the various classes of fire 18 8.1.1 Class A 18 8.1.2 Class B 19 8.1.3 Class C.19 8.1.4 Class D 19 8.1.5 Class F .20 8.2 Test fires General 20 ISO 2017 All rights reserved iii Contents Page ISO 7165:2017(E)8.2.1 Operators clothing .20 8.2.2 Requirements for extinguishment .20 8.2.3 Test extinguishe
10、rs and method of use 20 8.2.4 Test schedule 21 8.3 Class A test fire .21 8.3.1 Location 21 8.3.2 Construction .21 8.3.3 Procedure 22 8.4 Class B test fire .24 8.4.1 General.24 8.4.2 Location 24 8.4.3 Construction .25 8.4.4 Fuel .25 8.4.5 Procedure 26 8.4.6 Low-temperature extinguishing test .26 8.5
11、Class D test fire .26 8.5.1 General.26 8.5.2 Metal chip or turning fires 27 8.5.3 Metal powder or dust fires .28 8.5.4 Shallow liquid metal fires 28 8.5.5 Simulated casting fire .29 8.6 Electrical conductivity of extinguisher discharge 30 8.6.1 Water-based extinguishers 30 8.6.2 Requirements 30 8.6.
12、3 Test for electrical conductivity .30 8.7 Class F test fire .30 8.7.1 Location 30 8.7.2 Construction .30 8.7.3 Fuel .31 8.7.4 Procedure 31 8.8 Class F splash test 33 8.8.1 Location 33 8.8.2 Construction .33 8.8.3 Fuel .34 8.8.4 Procedure 34 8.8.5 Requirements 36 9 Construction requirements 36 9.1 H
13、igh-pressure extinguishers 36 9.2 Low-pressure extinguishers .36 9.2.1 General requirements .36 9.2.2 Burst test .37 9.2.3 Crushing test.37 9.2.4 Permanent volumetric expansion test .38 9.2.5 Welded low-carbon steel cylinder .38 9.2.6 Stainless steel cylinders 39 9.2.7 Aluminium cylinders .39 9.3 Ca
14、rrying handle .39 9.4 Mounting .40 9.5 Caps, valves and closures 40 9.6 Safety devices 41 9.7 Manufacturing tests .41 9.7.1 Low-pressure cylinders 41 9.7.2 Leakage tests 41 9.8 Requirements for plastics components 41 9.8.1 General requirements .41 9.8.2 Requirements for normally pressurized componen
15、ts .42 9.8.3 Ultraviolet light exposure 42 9.8.4 Impact resistance .43 iv ISO 2017 All rights reserved ISO 7165:2017(E)9.8.5 Normally non-pressurized components .43 9.8.6 Test for exposure to extinguishing medium 43 9.9 Hose assemblies 43 9.10 Method of operation 44 9.11 Safety-locking devices 45 9.
16、12 Requirements for pressure gauges and indicators for low-pressure extinguishers 46 9.12.1 General.46 9.12.2 Calibration test Gauges and indicators .47 9.12.3 Burst strength test Gauges and indicators 47 9.12.4 Overpressure test Gauges 47 9.12.5 Impulse test Gauges 48 9.12.6 Pressure gauge relief t
17、est 48 9.12.7 Water resistance test Gauges and indicators 48 9.12.8 Leakage test Gauges and indicators 48 9.12.9 Plastics components Gauges and indicators48 9.13 Dip-tubes and filters Water-based extinguishers .48 9.14 Special requirements for CO 2extinguishers 49 9.15 Gasket and O-rings 49 9.15.1 T
18、ensile strength, elongation, maximum set and hardness49 9.15.2 Compression set 49 10 Marking and colour 50 10.1 Colour .50 10.2 Marking 50 10.2.1 General.50 10.2.2 Use-code symbols 52 10.2.3 Recharging instructions 53 10.3 Inspection instructions .53 11 Manuals .54 11.1 User manual 54 11.2 Service m
19、anual .54 Annex A (normative) Alternate test fire for powder extinguishers with a rating exceeding 144B 55 Annex B (normative) Polar solvents 60 Annex C (normative) Clean agent FK-5-1-12 Extinguishing agent physical properties 63 Annex D (normative) Clean agent HCFC Blend B Extinguishing agent physi
20、cal properties 66 Annex E (normative) Clean agent HFC-227ea Extinguishing agent physical properties .69 Annex F (normative) Clean Agent HFC-236fa Extinguishing agent physical properties 72 Bibliography .75 ISO 2017 All rights reserved v ISO 7165:2017(E) Foreword ISO (the International Organization f
21、or Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has th
22、e right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The proc
23、edures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editori
24、al rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rig
25、hts identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an
26、 explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: w w w .
27、i s o .org/ iso/ foreword .html. This document was prepared by Technical Committee ISO/TC 21, Equipment for fire protection and fire fighting, Subcommittee SC 2, Manually transportable fire extinguishers. This third edition cancels and replaces the second edition (ISO 7165:2009), which has been tech
28、nically revised. The main changes compared to the previous edition are as follows: new requirements for four clean agents have been added; tests using polar solvents as a fuel for water-based fire extinguishers have been added.vi ISO 2017 All rights reserved INTERNATIONAL ST ANDARD ISO 7165:2017(E)
29、Fire fighting Portable fire extinguishers Performance and construction 1 Scope This document specifies the principal requirements intended to ensure the safety, reliability and performance of portable fire extinguishers. It is applicable to a fully charged extinguisher having a maximum mass of 20 kg
30、. Subject to local acceptance, application can be extended to extinguishers having a total mass of up to 25 kg when fully charged. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For
31、 dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4892-2:2013, Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc lamps ISO 5923, Equipment for fire protection and f
32、ire fighting Fire extinguishing media Carbon dioxide ISO 7202, Fire protection Fire extinguishing media Powder ISO 7203 (all parts), Fire extinguishing media Foam concentrates ISO 9227, Corrosion tests in artificial atmospheres Salt spray tests ISO 10619-2:2011, Rubber and plastics hoses and tubing
33、Measurement of flexibility and stiffness Part 2: Bending tests at sub-ambient temperatures ISO 11601, Fire fighting Wheeled fire extinguishers Performance and construction ISO 13061-1, Physical and mechanical properties of wood Test methods for small clear wood specimens Part 1: Determination of moi
34、sture content for physical and mechanical tests 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .el
35、ectropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp 3.1 batch group of the same products made on the same production line using the same lot of materials during one production shift 3.2 bulk range range of the extinguisher when 50 % of its media has been expelle
36、d ISO 2017 All rights reserved 1 ISO 7165:2017(E) 3.3 charge of extinguisher mass or volume of the extinguishing medium (3.9) contained in the extinguisher expressed in volume (litres) for water-based extinguishers and in mass (kilograms) for other extinguishers 3.4 classification of fires grouping
37、of fires on the basis of the characteristics as given in 3.4.1 to 3.4.5 Note 1 to entry: See ISO 3941. 3.4.1 class A involving solid materials, usually of an organic nature, in which combustion normally takes place with the formation of glowing embers 3.4.2 class B involving liquids or liquefiable s
38、olids 3.4.3 class C involving gases 3.4.4 class D involving metals 3.4.5 class F involving cooking media (vegetable or animal oils and fats) in cooking appliances 3.5 clean agent electrically non-conductive gaseous or vapourizing liquid fire extinguishant that does not leave a residue upon evaporati
39、on Note 1 to entry: For conductive properties and amount of residue, see Annexes C, D, E and F. 3.6 complete discharge point in the discharge of an extinguisher when the internal pressure has equalized with the external pressure, with the valve control being kept fully open 3.7 disposable extinguish
40、er non-rechargeable extinguisher extinguisher designed not to be recharged in the field or at the factory, but intended to be discarded after use 3.8 effective discharge time time from the commencement of discharge of the extinguishing medium (3.9) at the nozzle to the gas point (3.12) of the discha
41、rge stream with the control valve fully open 3.9 extinguishing medium substance contained in the extinguisher that causes extinguishment2 ISO 2017 All rights reserved ISO 7165:2017(E) 3.10 fill density mass in kilograms of extinguishing medium (3.9) per litre of container volume as fitted for use, c
42、omplete with valve and internal fittings 3.11 fire extinguisher appliance containing an extinguishing medium (3.9) that can be discharged and directed onto a fire by the action of internal pressure Note 1 to entry: Discharge may be achieved by stored pressure (constant pressurization of the extingui
43、shing media container); cartridge operated pressurization at the time of use by the release of a pressurizing gas stored in a separate high-pressure container (cartridge) 3.12 gas point point where the medium discharge changes from predominately liquid medium to predominately expellant gas 3.13 lowe
44、st observable adverse effect level LOAEL lowest concentration at which an adverse physiological or toxicological effect has been observed 3.14 low pressure extinguisher extinguisher having a service pressure, p s , not exceeding 25 bar 3.15 maximum service pressure p ms equilibrium pressure develope
45、d in a normally charged and pressurized extinguisher that is conditioned at 60 C for at least 18 h 3.16 portable fire extinguisher fire extinguisher (3.11) that is designed to be carried and operated by hand and that, in working order, has a mass of not more than 20 kg Note 1 to entry: Subject to lo
46、cal acceptance, extinguishers having a total mass of up to 25 kg when fully charged are permitted. 3.17 pressure gauge device that shows the pressure in the cylinder and the operating range of the extinguisher based on the operating temperature-pressure relationship Note 1 to entry: The gauge face i
47、s marked with the appropriate units. 3.18 pressure indicator device that shows that the extinguisher is pressurized at its rated expellant gas pressure 3.19 propellant non-flammable compressed gas used to expel the extinguishing medium (3.9) ISO 2017 All rights reserved 3 ISO 7165:2017(E) 3.20 recha
48、rgeable extinguisher extinguisher designed to be recharged after use 3.21 service pressure p s equilibrium pressure developed in a normally charged and pressurized extinguisher conditioned at 20 C for at least 18 h 3.22 wet chemical water-based chemical agents that include, but are not limited to, a
49、queous solutions of potassium acetate, potassium carbonate, potassium citrate or combinations of these materials 4 Classification of extinguishers Extinguishers shall be classified by the type of extinguishing medium that they contain. At present, the main classes of extinguishers are water-based, powder, carbon dioxide, and clean agents. These classes of extinguishers may be further sub-divided. For example, water-based extinguishers may contain pure water or wa
