欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ISO 6119-2006 Road vehicles - Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120C ma.pdf

    • 资源ID:1254559       资源大小:255.50KB        全文页数:16页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ISO 6119-2006 Road vehicles - Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120C ma.pdf

    1、 Reference number ISO 6119:2006(E) ISO 2006INTERNATIONAL STANDARD ISO 6119 Second edition 2006-08-01 Road vehicles Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 C max.) Vhicules routiers Joints en caoutchouc pour cylind

    2、res de freins hydrauliques disque utilisant un liquide de frein base non ptrolire (Temprature maximale dutilisation: 120 C) ISO 6119:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be ed

    3、ited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a

    4、trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member b

    5、odies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechan

    6、ical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.

    7、org Published in Switzerland ii ISO 2006 All rights reservedISO 6119:2006(E) ISO 2006 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Product requirements. 1 4 Brake test fluid 1 5 Apparatus 2 5.1 Apparatus for test of resistance to fluid at elevated temper

    8、ature, physical stability and precipitation characteristics 2 5.2 Apparatus for high-temperature strocking test (see Figure 1) . 2 5.3 Apparatus for low-temperature leakage test (see Figure 2) 3 6 Test requirements. 3 7 Preparation of test specimens 4 8 Resistance to fluid at elevated temperature Ph

    9、ysical stability . 4 8.1 Test specimens . 4 8.2 Test procedure 4 9 Resistance to fluid at elevated temperature Precipitation characteristics 5 9.1 Test specimens . 5 9.2 Test procedure 5 10 Resistance to elevated temperature in dry air.6 10.1 Test specimens . 6 10.2 Test procedure 6 11 Ambient-tempe

    10、rature stroking test. 6 11.1 Test specimens . 6 11.2 Test procedure 6 12 High-temperature stroking test . 7 12.1 Test specimens . 7 12.2 Test procedure 7 13 Low-temperature leakage test . 8 13.1 Test specimens . 8 13.2 Test procedure 8 13.3 Bend test procedure. 9 14 Cycling humidity storage corrosio

    11、n test 9 14.1 Test specimens . 9 14.2 Test procedure 9 ISO 6119:2006(E) iv ISO 2006 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normal

    12、ly carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the

    13、 work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare I

    14、nternational Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some o

    15、f the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6119 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 2, Braking systems and equipment. This second edition cancels a

    16、nd replaces the first edition (ISO 6119:1980), which has been technically revised. INTERNATIONAL STANDARD ISO 6119:2006(E) ISO 2006 All rights reserved 1 Road vehicles Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 C max

    17、.) 1 Scope This International Standard specifies the performance test methods and requirements for elastomeric seals used in road vehicle disc brake cylinders. It is applicable to solid section type seals (square, rectangular, “O”-ring), mounted stationary in the cylinder bore or on the movable pist

    18、on of disc brakes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 48,

    19、 Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD ISO 188, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tests ISO 1817, Rubber, vulcanized Determination of the effect of liquids ISO 4926, Road vehicles Hydraulic brake

    20、systems Non-petroleum base reference fluids ISO 4928, Road vehicles Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (Service temperature 120 C max.) 3 Product requirements Seals shall conform to the pertinent drawing in all resp

    21、ects and shall be free from blisters, pin-holes, cracks, protuberances, embedded foreign material, or other physical defects which can be detected by thorough inspection. These elastomeric seals shall be suitable for operation in a temperature range of 40 C to +120 C. 4 Brake test fluid The test flu

    22、id for all tests except the test prescribed in Clause 14 shall be compatibility fluid as defined in ISO 4926. The fluid specified in Clause 14 shall be ISO fluid for storage corrosion test as defined in ISO 4926, or the fluid agreed by the parties concerned. ISO 6119:2006(E) 2 ISO 2006 All rights re

    23、served5 Apparatus 5.1 Apparatus for test of resistance to fluid at elevated temperature, physical stability and precipitation characteristics 5.1.1 Oven, uniformly heated, dry air type conforming to the requirements of ISO 188. 5.1.2 Test jar, screw-top straight-sided round glass type, having a capa

    24、city of approximately 250 ml and inner dimensions of approximately 125 mm height and 50 mm diameter, with a tinned steel lid (no insert or organic coating). 5.2 Apparatus for high-temperature strocking test (see Figure 1) 5.2.1 Pneumatic or hydraulic pressure source. 5.2.2 Master cylinder. 5.2.3 Pre

    25、ssure gauge. 5.2.4 Wheel cylinder seat stroking fixture. 5.2.6 Cylinder assembly. 5.2.7 Oven, in accordance with 5.1.1. Key 1 pneumatic or hydraulic pressure source 2 master cylinder 3 pressure gauge 4 wheel cylinder seat stroking fixture 5 oven chamber at +120 C 6 cylinder assembly Figure 1 High-te

    26、mperature strocking test ISO 6119:2006(E) ISO 2006 All rights reserved 3 5.3 Apparatus for low-temperature leakage test (see Figure 2) 5.3.1 Hydraulic pressure gauge. 5.3.2 Master cylinder. 5.3.3 Cylinder assembly. 5.3.4 Cold chamber, at 40 C. Dimensions in millimetres Key 1 hydraulic pressure gauge

    27、 2 master cylinder 3 cylinder assembly 4 cold chamber at 40 C Figure 2 Low-temperature leakage test 6 Test requirements 6.1 After the test for resistance to fluid at elevated temperature (physical stability) (see Clause 8), the seals shall conform to the following requirements: a) any change in volu

    28、me shall be within 0 % to +15 %; b) any change in hardness shall be within 0 IRHD to 15 IRHD. 6.2 After the test for resistance to fluid at elevated temperature (precipitation characteristics) (see Clause 9), not more than 0,3 % sediment by volume shall be formed in the test fluid used. ISO 6119:200

    29、6(E) 4 ISO 2006 All rights reserved6.3 After the test for resistance to elevated temperature in dry air (see Clause 10), the seals shall conform to the following requirements: a) any change in hardness shall be within 0 IRHD to +15 IRHD; b) test specimens shall show no evidence of blistering, cracki

    30、ng or change in shape from original form. 6.4 After the ambient-temperature stroking test (see Clause 11), seals and assembly shall conform to the following requirements: a) no leakage beyond normal wetting of the bore(s) shall occur during the stroking test; b) no leakage beyond normal wetting of t

    31、he bore(s) shall occur during the static leak test (see 11.2.3). 6.5 After the high-temperature stroking test (see Clause 12), the seals and assembly shall conform to the following requirements: a) no leakage beyond normal wetting of the bore(s) shall occur during the stroking test; b) no leakage be

    32、yond normal wetting of the bore(s) shall occur during the static leak test (see 12.2.4). 6.6 After the low-temperature leakage test (see Clause 13), the seals and assembly shall conform to the following requirements: a) no leakage beyond normal wetting of the bore(s) shall occur during the test peri

    33、od or pressure application; b) the seal shall not crack, shall remain flexible and shall return to its approximate original shape within 1 min when tested according to the procedure given in 13.3. 6.7 After the cycling humidity storage corrosion test (Clause 14), the seals and assembly shall conform

    34、 to the following requirements: a) no evidence of rubber adhesion of the test seal(s) shall appear during disassembly of the test brake; b) no surface of the sealing systems shall show evidence of corrosion or deterioration which would interfere with proper sealing action; normal staining or discolo

    35、ration of metal parts is acceptable if the surface finish is unaffected. 6.8 After all the tests, disassemble the cylinder and inspect the seal. Record the visual condition of the seal bore and piston. Seals shall not show excessive deterioration such as scoring, scuffing, blistering, cracking or ch

    36、ange in shape from original appearance. 7 Preparation of test specimens All seals to be tested shall be cleaned prior to testing by rinsing in isopropanol then blown dry or wiped dry with a lint-free cloth. Seals shall not remain in the alcohol for more than 30 s. 8 Resistance to fluid at elevated t

    37、emperature Physical stability 8.1 Test specimens From three or more seals to be tested, obtain a sample of mass 3 g to 5 g. 8.2 Test procedure 8.2.1 Determine and record the initial volume of the sample in accordance with ISO 1817. ISO 6119:2006(E) ISO 2006 All rights reserved 5 8.2.2 Determine and

    38、record the initial hardness of the sample in IRHD. Measure the hardness as specified in ISO 48 using a microtester (or according to a procedure previously agreed upon between the vendor and purchaser). 8.2.3 Place the sample in the test jar (5.1.2) and completely immerse in 75 ml of brake test fluid

    39、 (see Clause 4). Seal the test jar to prevent vapour loss and place in the oven (5.1.1) at 120 C 2 C for 70 h. 8.2.4 After the 70 h, remove the sample from the oven and allow it to cool in the container at 23 C 5 C for 60 min to 90 min. At the end of the cooling period, remove the sample from the co

    40、ntainer and rinse it in isopropanol or ethanol then wipe dry with a clean, lint-free cloth. Do not allow the sample to remain in the alcohol for more than 30 s. 8.2.5 Within 60 min of removal from the liquid, determine and record the final volume and hardness, in IRHD, of each seal in accordance wit

    41、h 8.2.1 and 8.2.2. Average the results and report as the change in volume and hardness. 8.2.6 Report the change in volume V as a percentage of the original volume. It is given by the formula V = () ( ) () 3412 12 100 mmmm mm % where m 1is the initial mass, in grams, in air; m 2is the initial apparen

    42、t mass, in grams, in water; m 3is the mass, in grams, in air after immersion in the test fluid; m 4is the apparent mass, in grams, in water after immersion in the test fluid. 9 Resistance to fluid at elevated temperature Precipitation characteristics 9.1 Test specimens From two or more seals to be t

    43、ested, obtain a sample of 4,0 g 0,5 g. Since whole seals are quite large, small pieces may be cut from the seal to arrive at the required mass. Use a minimum number of pieces to obtain a sample of mass 4,0 g 0,5 g. 9.2 Test procedure 9.2.1 Place the sample in a test jar (5.1.2) and cover with 75 ml

    44、of the test fluid (see Clause 4). Seal the test jar to prevent vapour loss and place in the oven (5.1.1) at 120 C 2 C. (Optional: a blank test may be conducted on the brake fluid prior to the test, and any sediment resulting from this blank test may be deducted from the volume of sediment obtained a

    45、fter the test.) 9.2.2 After 70 h, remove the test jar from the oven. Allow the sample to remain in the fluid at room temperature for 24 h, after which agitate the test fluid and pour into a cone-shaped centrifuge tube of 100 ml capacity. 9.2.3 Rotate the centrifuge tube for 30 min at 1 500 min 1 . N

    46、ote the volume of sediment observed in the tube. Repeat the above rotation for an additional 30 min and record any difference in volume of sediment. 9.2.4 Record the percentage amount of sediment obtained after the second centrifuging. ISO 6119:2006(E) 6 ISO 2006 All rights reserved10 Resistance to

    47、elevated temperature in dry air 10.1 Test specimens Two or more seals shall be used. 10.2 Test procedure 10.2.1 Measure and record the hardness of each seal in IRHD in accordance with 8.2.2. 10.2.2 Place the test seals in a circulating air oven, as specified in ISO 188, and maintain at 120 C 2 C for

    48、 70 h. 10.2.3 At the termination of the heating period, remove the seals from the oven and allow to cool for 16 h to 96 h at room temperature. 10.2.4 After cooling, measure and record the hardness in IRHD, in accordance with 8.2.2, and note any visual change such as cracking, blistering or distortio

    49、n. 11 Ambient-temperature stroking test 11.1 Test specimens An adequate number of test seals for at least one complete calliper shall be prepared. 11.2 Test procedure 11.2.1 Installation 11.2.1.1 Moisten the seals and calliper bores with brake test fluid (see Clause 4). Install the test seals in the cylinder. 11.2.1.2 Complete the test calliper assembly, placing the piston so as to simulate a half-worn lining position. 11.2.1.3 Mount the test calliper assembly on a pr


    注意事项

    本文(ISO 6119-2006 Road vehicles - Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120C ma.pdf)为本站会员(刘芸)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开