1、 ISO 2014 Thermal insulating products for building applications Determination of dimensional stability under constant normal laboratory conditions (23 degrees C/50 % relative humidity) AMENDMENT 1 Produits isolants thermiques destins aux applications du btiment Dtermination de la stabilit dimensionn
2、elle dans des conditions de laboratoire constantes et normales (23 degrs C/50 % dhumidit relative) AMENDEMENT 1 INTERNATIONAL STANDARD ISO 29471 First edition 2008-11-01 Reference number ISO 29471:2008/Amd.1:2014(E) AMENDMENT 1 2014-12-01 ISO 29471:2008/Amd.1:2014(E)ii ISO 2014 All rights reserved C
3、OPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written pe
4、rmission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 294
5、71:2008/Amd.1:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a
6、 subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commissio
7、n (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents shoul
8、d be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for ide
9、ntifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the conve
10、nience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword
11、 - Supplementary information The committee responsible for this document is ISO/TC 163, Thermal performance and energy use in the built environment, Subcommittee SC 1, Test and measurement methods. ISO 2014 All rights reserved iii Thermal insulating products for building applications Determination o
12、f dimensional stability under constant normal laboratory conditions (23 degrees C/50 % relative humidity) AMENDMENT 1 Change the title to: Thermal insulating products for building applications Determination of dimensional stability under constant normal laboratory conditions (23 C/50 % relative humi
13、dity or in tropical countries 27 C/65 % relative humidity) Page V, Introduction Replace the existing Introduction with the following: This International Standard comprises the original EN 1603:1996 and EN 1603:1996/AC:1997 prepared by Technical Committee CEN/TC 88, Thermal insulating materials and p
14、roducts, which have been amended by ISO/TC 163/SC 1 with reference to conditioning and testing conditions in tropical countries. This International Standard is one of a series of documents specifying test methods, based on existing European Standards that are being adopted by ISO. This “package” of
15、standards includes the following group of interrelated documents. ISO standard Title Respective EN standard ISO 12344 Thermal insulating products for building applications Determination of bending behaviour EN 12089 ISO 12968 Thermal insulation products for building applications Determination of the
16、 pull-off resistance of external thermal insulation composite systems (ETICS) (foam block test) EN 13495 ISO 29465 Thermal insulating products for building applications Determination of length and width EN 822 ISO 29466 Thermal insulating products for building applications Determination of thickness
17、 EN 823 ISO 29467 Thermal insulating products for building applications Determination of squareness EN 824 ISO 29468 Thermal insulating products for building applications Determination of flatness EN 825 ISO 29469 Thermal insulating products for building applications Determination of compression beh
18、aviour EN 826 ISO 29470 Thermal insulating products for building applications Determination of the apparent density EN 1602 ISO 29471:2008/Amd.1:2014(E) ISO 2014 All rights reserved 1 ISO 29471:2008/Amd.1:2014(E) ISO 29471 Thermal insulating products for building applications Determination of dimens
19、ional stability under constant normal laboratory conditions (23 degrees C/50 % relative humidity or in tropical countries 27 C/65 % relative humidity) EN 1603 ISO 29472 Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidi
20、ty conditions EN 1604 ISO 29764 Thermal insulating products for building applications Determination of deformation under specified compressive load and temperature conditions EN 1605 ISO 29765 Thermal insulating products for building applications Determination of tensile strength perpendicular to fa
21、ces EN 1607 ISO 29766 Thermal insulating products for building applications Determination of tensile strength parallel to faces EN 1608 ISO 29767 Thermal insulating products for building applications Determination of short-term water absorption by partial immersion EN 1609 ISO 29768 Thermal insulati
22、ng products for building applications Determination of linear dimensions of test specimens EN 12085 ISO 29769 Thermal insulating products for building applications Determination of behaviour under point load EN 12430 ISO 29770 Thermal insulating products for building applications Determination of th
23、ickness for floating-floor insulating products EN 12431 ISO 29771 Thermal insulating materials for building applications Determination of organic content EN 13820 ISO 29803 Thermal insulation products for building applications Determination of the resistance to impact of external thermal insulation
24、composite systems (ETICS) EN 13497 ISO 29804 Thermal insulation products for building applications Determination of the tensile bond strength of the adhesive and of the base coat to the thermal insulation material EN 13494 ISO 29805 Thermal insulation products for building applications Determination
25、 of the mechanical properties of glass fibre meshes EN 13496 ISO 16534 Thermal insulating products for building applications Determination of compressive creep EN 1606 ISO 16535 Thermal insulating products for building applications Determination of long-term water absorption by immersion EN 12087 IS
26、O 16536 Thermal insulating products for building applications Determination of long-term water absorption by diffusion EN 12088 ISO 16537 Thermal insulating products for building applications Determination of shear behaviour EN 12090 ISO 16544 Thermal insulating products for building applications Co
27、nditioning to moisture equilibrium under specified temperature and humidity conditions EN 12429 ISO 16545 Thermal insulating products for building applications Determination of behaviour under cyclic loading EN 137932 ISO 2014 All rights reserved ISO 29471:2008/Amd.1:2014(E) ISO 16546 Thermal insula
28、ting products for building applications Determination of freezethaw resistance EN 12091 A further series of existing European Standards on test methods for products used to insulate building equipment and industrial installations was adopted by ISO. This “package” of standards comprises the followin
29、g group of interrelated standards: ISO standard Title Respective EN standard ISO 12623 Thermal insulating products for building equipment and industrial installations Determination of short-term water absorption by partial immersion of preformed pipe insulation EN 13472 ISO 12624 Thermal insulation
30、products Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH EN 13468 ISO 12628 Thermal insulating products for building equipment and industrial installations Determination of dimensions, squareness and linearity of preformed pipe insu- lation EN 1346
31、7 ISO 12629 Thermal insulating products for building equipment and industrial installations Determination of water vapour transmission properties of preformed pipe insulation EN 13469 ISO 18096 Thermal insulating products for building equipment and industrial installations Determination of maximum s
32、ervice temperature for preformed pipe insulation EN 14707 ISO 18097 Thermal insulating products for building equipment and industrial installations Determination of maximum service temperature EN 14706 ISO 18098 Thermal insulating products for building equipment and industrial installations Determin
33、ation of the apparent density of preformed pipe insulation EN 13470 ISO 18099 Thermal insulating products for building equipment and industrial installations Determination of the coefficient of thermal expansion EN 13471 The Application of Agreement on technical cooperation between ISO and CEN (Vien
34、na Agreement), Modes 1, 2, 4, and 5, was not approved by CEN/TC 88 and the necessity not seen by its stakeholders. Page 1, subclause 3 Change the existing definition to: 3.4 normal laboratory conditions (23 2) C and (50 5) % relative humidity or in tropical countries (27 2) C and (65 5) % relative humidity ISO 2014 All rights reserved 3 ISO 29471:2008/Amd.1:2014(E) ISO 2014 All rights reserved IC S 91.100.60 Price based on 3 pages
