1、 ISO 2015 Small craft Permanently installed petrol and diesel fuel tanks AMENDMENT 2 Petits navires Rservoirs carburant essence et diesel installs demeure AMENDEMENT 2 INTERNATIONAL STANDARD ISO 21487 Second edition 2012-11-15 Reference number ISO 21487:2012/Amd.2:2015(E) AMENDMENT 2 2015-11-15 ISO
2、21487:2012/Amd.2:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, includin
3、g photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel.
4、 +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO 21487:2012/Amd.2:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally car
5、ried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
6、 ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the differ
7、ent approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may
8、 be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patent
9、s). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principl
10、es in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information. The committee responsible for this document is ISO/TC 188, Small craft, SC 2, Engines and propulsion systems. ISO 2015 All rights reserved iii Small craft Permanently installed petrol and diesel
11、fuel tanks AMENDMENT 2 Pages 4(end) and 5: With the purpose of improvement of test sequence/understanding and allowing air to be used for leakage tests, replace Clause 7.2 with: 7.2 Hydraulic pressure test WARNING Do not to exceed the maximum static test pressure. Do not use solutions containing amm
12、onia for testing. 7.2.1 Hydraulic pressure/strength type test A tank representative of the tank series type, with all its accessories, shall be pressure type tested. Prior to the test, non-metal tanks shall be filled with test liquid C in accordance with ISO 1817 or the fuel for which the tank is fa
13、bricated and stored for at least 28 days at an ambient temperature of (21 +2/0)C. The hydraulic pressure test shall be performed immediately after emptying the test liquid out of the tank. The pressure shall be gradually increased to the greater of: 20 kPa; or 1,5 times the highest hydrostatic press
14、ure to which the tank can be subjected in service (maximum fill-up height above tank top). This pressure shall be maintained for: 1 min for metal tanks; 60 min for thermoplastic and fibre reinforced plastic (FRP) tanks with inner coatings having a density 935 kg/m 3 ; and 5 h for thermoplastic and f
15、ibre reinforced plastic (FRP) tanks with inner coatings having a density 935 kg/m 3 . During this time, the tank shell shall not crack or leak; however, it may be permanently deformed. 7.2.2 Leakage test Each fuel tank identical to a type tested tank shall be internally leakage tested with a test pr
16、essure of 20 kPa. Air pressure may be used as an alternative to hydraulic pressure for this test. The test pressure shall be applied for 5 min without pressure drop or rise. After the test, the fuel tank shall not show any leakage when using a leak detection method other than the pressure-drop method. WARNING If air is used for this test care should be taken not to exceed a test pressure of 20 kPa. ISO 21487:2012/Amd.2:2015(E) ISO 2015 All rights reserved 1 ISO 21487:2012/Amd.2:2015(E) ISO 2015 All rights reserved IC S 47.080 Price based on 1 page