1、 Reference number ISO 17080:2005(E) ISO 2005INTERNATIONAL STANDARD ISO 17080 First edition 2005-10-15 Manually portable agricultural and forestry machines and powered lawn and garden equipment Design principles for single-panel product safety labels Tracteurs et matriels agricoles et forestiers port
2、atifs et matriels moteur pour jardins et pelouses Principes de conception des tiquettes de scurit de produit encadr unique ISO 17080:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be ed
3、ited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a
4、trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member b
5、odies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechan
6、ical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.
7、org Published in Switzerland ii ISO 2005 All rights reservedISO 17080:2005(E) ISO 2005 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards i
8、s normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take par
9、t in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to p
10、repare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility tha
11、t some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 17080 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 14, Operator con
12、trols, operator symbols and other displays, operator manuals. ISO 17080:2005(E) iv ISO 2005 All rights reservedIntroduction There is need for a standardized system for the communication of specific safety information on products, and ISO 17080 helps meet that need by providing formats for single-pan
13、el product safety labels that can be used to fulfil the requirements of both the product and its user. The formats for single-panel product safety labels presented in this International Standard incorporate the use of geometric shapes, colours and hazard pictorials (graphical symbols) to communicate
14、 safety information, efficiently, across language barriers. Education is an essential part of any system of safety information. Because the amount of information necessary to enable a product to be operated or serviced safely could well be more than is able to be conveyed in a product safety label,
15、collateral material (e.g. product literature, installation manual, operators manual, service manual, etc.) can be used to supplement product safety labels and provide the user with additional safety information. INTERNATIONAL STANDARD ISO 17080:2005(E) ISO 2005 All rights reserved 1 Manually portabl
16、e agricultural and forestry machines and powered lawn and garden equipment Design principles for single-panel product safety labels 1 Scope This International Standard establishes principles and gives requirements for the design of single-panel product safety labels intended to be permanently affixe
17、d to manually portable agricultural and forestry machines and powered lawn and garden equipment. The main usage of these labels is on machines and equipment where the available space for locating product safety information is very limited, and where multi- panel labels are not necessary for conveyin
18、g the essential safety messages. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 hazard source of potential injury to a person 2.2 panel area of a product safety label that has a distinctive background colour different from adjacent areas of
19、the label, or which is clearly delineated by a border 2.3 multi-panel product safety label product safety label that uses more than one panel to communicate the safety message NOTE See ISO 11684. 2.4 product safety label label on a product that informs the observer of one or more hazards and/or desc
20、ribes the safety precautions or actions required to avoid the hazard(s) NOTE A product safety label communicates a hazardous situation, a precaution to avoid a hazard, and/or a result of not avoiding a hazard. 2.5 safety colour colour with special properties to which a safety meaning is attributed 2
21、.6 single-panel product safety label product safety label that uses one panel to communicate the safety message ISO 17080:2005(E) 2 ISO 2005 All rights reserved3 Safety colours and contrast colours 3.1 Purposes There are two basic purposes for using specific colours on a product safety label. First,
22、 the use of colour rapidly draws attention to the product safety label so that it is easily noticed. Second, safety colour coding serves to identify and give meaning (through training and/or repeated exposure) to the product safety label as a whole as well as to its component parts. Product safety l
23、abels should be conspicuous on the product. This can be achieved by ensuring that the safety colour of the geometric shape is sufficiently distinctive on the product surface to which the product safety label is affixed, and/or adding a border of a specified contrast colour (see 4.4, 4.5, 4.6), and/o
24、r enclosing the geometric shape within a larger rectangle of white or for hazard description (warning) labels of yellow or white. 3.2 Chromaticity The chromaticity of the single-panel product safety labels shall be in accordance with Table 1. Table 1 Chromaticity of single-panel product safety label
25、s Chromaticity coordinates of corner points determining permitted colour area for standard illuminant D65 and CIE 2 standard observer Colour 1 2 3 4 x 0,660 0,610 0,700 0,735 Red y 0,340 0,340 0,250 0,265 x 0,494 0,470 0,493 0,522 Yellow y 0,505 0,480 0,457 0,477 x 0,140 0,160 0,160 0,140 Blue y 0,1
26、40 0,140 0,160 0,160 x 0,305 0,335 0,325 0,295 White y 0,315 0,345 0,355 0,325 x 0,385 0,300 0,260 0,345 Black y 0,355 0,270 0,310 0,395 NOTE The values for red, yellow, blue and white correspond to the values for ordinary materials given in ISO 3864-1:2002, Table 3, while those for black correspond
27、 to the values in ISO 3864-1:2002, Table 2. ISO 17080:2005(E) ISO 2005 All rights reserved 3 4 Single-panel product safety labels 4.1 Uses of label A single-panel product safety label can be used alone to describe a hazard, a prohibited action, or a mandatory action. In many cases, both hazard descr
28、iption and hazard avoidance information must be communicated for the same hazard. A multi-panel product safety label (see ISO 11684) is appropriate in such cases. Alternatively, it is possible to use two or more single-panel product safety labels in conjunction with one another. For example, a singl
29、e-panel hazard description (warning) product safety label may be placed adjacent to a single-panel mandatory action product safety label and/or single-panel prohibited action product safety label. 4.2 Types of label There are three types of single-panel product safety label: hazard description (warn
30、ing) product safety labels (see 4.4); prohibited action product safety labels (see 4.5); mandatory action product safety labels (see 4.6). 4.3 Geometric shape and colour of label Single-panel product safety labels use geometric shapes, colours, and hazard pictorials (graphical symbols) to communicat
31、e information about hazards, prohibited actions and mandatory actions. When a geometric shape is used around a hazard pictorial, the corresponding safety colour shall identify the type of safety information to be conveyed by the hazard pictorial. See Table 2. Table 2 Geometric shapes and colours of
32、single-panel product safety labels Geometric shape Meaning Safety colour Contrast colour Hazard pictorial colour Description Hazard description (Warning) Yellow Black Black Black hazard pictorial on yellow equilateral triangle enclosed by black triangular band Warns that hazard exists and describes
33、its nature and/or consequences Prohibited action Red White Black Black hazard pictorial on white circle enclosed by red circular band with red diagonal bar Depicts action NOT to be taken or action to be stopped in order to avoid hazard Mandatory action Blue White White White hazard pictorial on blue
34、 circle Depicts action to be taken in order to avoid hazard ISO 17080:2005(E) 4 ISO 2005 All rights reserved4.4 Single-panel hazard description (warning) product safety label 4.4.1 Application Hazard description (warning) product safety labels indicate a potential personal injury hazard. Single-pane
35、l labels of this type communicate information about a hazard and/or its potential consequences by a combination of geometric shape, colour and hazard-description pictorial. 4.4.2 Format Single-panel hazard description (warning) product safety labels shall conform to the format as shown in Figure 1.
36、Their geometric shape shall consist of an equilateral triangular band with rounded corners of nominal radius 0,06 b. The background colour shall be yellow. The triangular band shall be black. If a border is used, it shall be yellow with a width of 0,025 b to 0,05 b. The hazard description pictorial
37、representing the hazard shall be black. The label may be placed on a yellow or white background panel. Colours Background: yellow Triangular band: black Pictorial: black Border: yellow Figure 1 Format of single-panel hazard description (warning) product safety label 4.5 Single-panel prohibited actio
38、n product safety label 4.5.1 Application Prohibited action product safety labels indicate that a specified action is not to be taken or is to be stopped in order avoid a hazard. Single-panel labels of this type communicate information about how a hazard can be avoided by a combination of geometric s
39、hape, colour, and hazard avoidance pictorial. 4.5.2 Format Single-panel prohibited action product safety labels shall conform to the format as shown in Figure 2. Their geometric shape shall consist of a circular band with diagonal bar. The background colour shall be white. The circular band and diag
40、onal bar shall be red. If a border is used, it shall be white with a width of 0,025 d to 0,05 d. The hazard avoidance pictorial representing the prohibited action shall be black and shall be placed within the red circular band with diagonal bar. The label may be placed on a white background panel. I
41、SO 17080:2005(E) ISO 2005 All rights reserved 5Colours Background: white Circular band: red Diagonal bar: red Pictorial: black Border: white Figure 2 Format of single-panel prohibited action product safety label 4.6 Single-panel mandatory action product safety label 4.6.1 Application Mandatory actio
42、n product safety labels indicate that a specified action is to be taken in order to avoid a hazard. Single-panel labels of this type communicate information about how a hazard can be avoided by a combination of geometric shape, colour, and hazard avoidance pictorial. 4.6.2 Format Single-panel mandat
43、ory action product safety labels shall conform to the format as shown in Figure 3. The geometric shape for single-panel mandatory action product safety labels shall consist of a filled circle. The filled circle colour shall be blue. If a border is used, it shall be white with a width of 0,025 d to 0
44、,05 d. The hazard avoidance pictorial representing the mandatory action shall be white and shall be placed within the blue circle. The single-panel mandatory action product safety label may be placed on a white background panel. Colours Background: blue Pictorial: white Border: white Figure 3 Format
45、 of single-panel mandatory action product safety label ISO 17080:2005(E) 6 ISO 2005 All rights reserved5 Principles and guidelines for design of hazard pictorials ISO 11684:1995, Annex D, provides principles and guidelines for the graphical design of hazard pictorials, as well as for drawing the hum
46、an figure and the presentation of other graphical elements used in hazard pictorials. Good, consistent visual design is important for conveying the meaning of both hazard description and hazard avoidance pictorials. 6 Examples of single-panel safety labels Annex A presents some examples of single-pa
47、nel product safety labels. Additional single-panel product safety labels might need to be developed for other hazard descriptions, prohibited actions or mandatory actions. ISO 17080:2005(E) ISO 2005 All rights reserved 7 Annex A (informative) Examples of single-panel product safety labels A.1 Exampl
48、es of hazard description (warning) single-panel product safety labels Meaning Single-panel product safety label Description of image content A.1.1 Beware of blade thrust Continued movement of saw blade after cutting through log A.1.2 Beware of thrown objects Multiple objects moving toward human figu
49、re A.1.3 Beware of chain saw kickback and avoid contact with bar tip Movement of chain saw upward from log ISO 17080:2005(E) 8 ISO 2005 All rights reservedA.2 Examples of prohibited action single-panel product safety labels Meaning Single-panel product safety label Description of image content A.2.1 Do not use metal blades Two types of blades A.2.2 Do not use saw blades Saw blade Chain saw held in one hand A.2.3 Do not use chain saw one- handed NOTE Normally used in conjunction with A.3.1. ISO 1708