1、 Reference number ISO 13584-102:2006(E) ISO 2006INTERNATIONAL STANDARD ISO 13584-102 First edition 2006-11-15 Industrial automation systems and integration Parts library Part 102: View exchange protocol by ISO 10303 conforming specification Systmes dautomatisation industrielle et intgration Biblioth
2、que de composants Partie 102: Protocole dchange de vue par spcification de conformit ISO 10303 ISO 13584-102:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typeface
3、s which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Syste
4、ms Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely e
5、vent that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocop
6、ying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzer
7、land ii ISO 2006 All rights reserved ISO 13584-102:2006(E) ISO 2006 All rights reserved iiiContents PageForeword iv Introduction . vi 1 Scope 1 2 Normative references2 3 Terms, definitions, and abbreviations .2 4 Identification of the ISO10303_rep representation category 6 4.1 Concepts .6 4.2 Standa
8、rdized dictionary entries.7 4.2.1 General.7 4.2.2 View logical name 7 4.2.3 View control variables 8 4.3 Rules for the ISO10303_rep representation category 9 4.3.1 General.9 4.3.2 Step_ap 10 4.3.3 Step_cc.10 4.3.4 Detail level10 4.3.5 Side 10 4.3.6 Variant 11 5 Exchange format.11 5.1 General11 5.2 E
9、xternal referent assignment 12 5.3 One representation per file12 6 Conformance requirements 13 6.1 General13 6.2 Implementation resources.14 6.3 Implementation methods.14 6.4 Constraints on a library delivery file for referencing this view exchange protocol 15 6.4.1 General.15 6.4.2 Conformance clas
10、s specification16 6.4.3 Constraints on a library delivery file referencing ISO10303_rep16 Annex A (normative) Information object registration.22 Bibliography .23 Index 24 Figures Figure 1 Meaning of side view control variable 11 Figure 2 Method 1: external referent assignment 12 Figure 3 Method 2: f
11、ile name13 Tables Table 1 View logical name description.7 Table 2 View control variables of the ISO10303_rep functional view class.9 ISO 13584-102:2006(E) iv ISO 2006 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards
12、bodies(ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizati
13、ons, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the
14、 ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of t
15、he member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13584-102 was prepared by Technical Committee ISO/TC 184, Indust
16、rial automation systems and integration, Subcommittee SC4, Industrial data. ISO 13584 consists of the following parts under the general title Industrial automation systems and integration Parts library: Part 1: Overview and fundamental principles; Part 20: Logical resource: Logical model of expressi
17、ons; Part 24: Logical resource: Logical model of supplier library; Part 25 : Logical resource: Logical model of supplier library with aggregate values and explicit content; Part 26: Logical resource: Information supplier identification; Part 31: Implementation resources: Geometric programming interf
18、ace; Part 42: Description methodology: Methodology for structuring part families; Part 101: Geometrical view exchange protocol by parametric program; Part 102: VView exchange protocol by ISO 10303 conforming specification; Part 5501: Reference dictionary for measuring instruments Registration proced
19、ure; Part 5511: Mechanical systems and components for general use Reference dictionary for fasteners. The structure of the ISO 13584 series is described in ISO 13584-1. The numbering of the parts of ISO 13584 reflects its structure: Parts 10 to 19 specify the conceptual descriptions, Parts 20 to 29
20、specify the logical resources, ISO 13584-102:2006(E) ISO 2006 All rights reserved v Parts 30 to 39 specify the implementation resources, Parts 40 to 49 specify the description methodology, Parts 100 to 199 specify the view exchange protocols, Parts 500 to 599 specify reference dictionaries for speci
21、fic application domains. Should further parts of ISO 13584 be published, they will follow the same numbering pattern. ISO 13584-102:2006(E) vi ISO 2006 All rights reservedIntroduction ISO 13584 is an International Standard for the computer-interpretable representation and exchange of part library da
22、ta. The objective is to provide a neutral mechanism capable of transferring parts library data, independent of any application that is using a parts library data system. The nature of this description makes it suitable not only for the exchange of files containing parts, but also as a basis for impl
23、ementing and sharing databases of parts library data. ISO 13584 is organized as a series of parts, each published separately. The parts of ISO 13584 fall into one of the following series: conceptual descriptions, logical resources, implementation resources, description methodology, view exchange pro
24、tocol, and standardized content. The series are described in ISO 13584-1. This part of ISO 13584 is a member of the view exchange protocol series. A view exchange protocol specifies how a particular representation category of the items described in a parts library may be exchanged in a library excha
25、nge context. It defines the identification of the representation category, the means to be used to exchange representations that belong to this representation category, the implementation resources that shall be available on any implementation that claims conformance to this view exchange protocol,
26、and the standard data that shall be recognized by any implementation that claims conformance to this view exchange protocol. This part of ISO 13584 specifies how representations of the items described in a parts library may be exchanged by means of a representation conforming to one application prot
27、ocol of ISO 10303 (ISO 10303 parts numbered between 200 and 299). INTERNATIONAL STANDARD ISO 13584-102:2006(E) ISO 2006 All rights reserved 1 1 Scope This part of ISO 13584 specifies a representation category, called ISO10303_rep. This representation category captures the generic concepts used to de
28、scribe the representation of a product in ISO 10303 application protocols. This representation category may be associated with any of the items defined in a parts library. This part of ISO 13584 also defines how representations that belong to this representation category may be exchanged within a li
29、brary exchange context by means of ISO 10303 compliant data repositories. The following are within the scope of this part of ISO 13584: the definition of the ISO10303_rep representation category, and the mechanisms that are to be used to reference it; the properties used to characterize a particular
30、 representation within the ISO10303_rep representation category; the implementation resources to be supported by any implementation that claims conformance to this part of ISO 13584; the dictionary entries to be supported by any implementation that claims conformance to this part of ISO 13584; the s
31、tandard data to be recognized by any implementation that claims conformance to this part of ISO 13584. The following are outside the scope of this part of ISO 13584: the structure and exchange format of library delivery files; the structure and exchange format of library external files that conform
32、to ISO 10303 application protocols. NOTE 1 The structure of a library delivery file is defined by a library integrated information model specified in one of the logical resource series parts of ISO 13584. NOTE 2 The ISO13584_f_m_iim_schema, documented in ISO 13584-24:2003, is a library integrated in
33、formation model that defines the structure of a library delivery file. Such a library delivery file may contain instance values that reference the representation category and/or the library external files defined in this part of ISO 13584. Annex A, which provides information on document identificati
34、on, forms an integral part of this part of ISO 13584. Industrial automation systems and integration Parts library Part 102: View exchange protocol by ISO 10303 conforming specification ISO 13584-102:2006(E) 2 ISO 2006 All rights reserved2 Normative references The following referenced documents are i
35、ndispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 10303-11:1994, Industrial automation systems: and integration Product data representa
36、tion and exchange Part 11: Description methods: The EXPRESS language reference manual. ISO 10303-21:1994, Industrial automation systems and integration Product data representation and exchange Part 21: Implementation methods: Clear text encoding of the exchange structure . ISO 10303-41:2000, Industr
37、ial automation systems and integration Product data representation and exchange Part 41: Integrated generic resource: Fundamentals of product description and support. ISO 10303-43:2000, Industrial automation systems and integration Product data representation and exchange Part 43. Integrated generic
38、 resource: Representation structures. ISO 13584-24:2003, Industrial automation systems and integration Parts Library Part 24: Logical resource: Logical model of supplier library ISO 13584-42:1998, Industrial automation systems and integration Parts Library Part 42: Description methodology: Methodolo
39、gy for structuring part families ISO/IEC 8824-1:2002, Information technology Abstract Syntax Notation One (ASN.1) Part 1: Specification of basic notation. 3 Terms, definitions, and abbreviations For the purposes of this document, the following terms and definitions apply. Some of these terms and def
40、initions are repeated for convenience from: ISO 10303-1:1994; ISO 10303-11:1994; ISO 10303-31:1994; ISO 13584-1:2001; ISO 13584-24:2003; ISO 13584-42:1998. 3.1 AP conformance class subset of an application protocol for which conformance may be claimed ISO 10303-1:1994 ISO 13584-102:2006(E) ISO 2006
41、All rights reserved 33.2 application group of one or more processes creating or using product data ISO 10303-1:1994 3.3 application context conditions that define the intended use of product data within an application ISO 10303-1:1994 3.4 application programming interface API set of functions that m
42、ay be triggered by a program ISO 13584-24:2003 3.5 application protocol AP part of ISO 10303 that describes the use of (ISO 10303) integrated resources satisfying the scope and information requirements for a specific application context ISO 10303-1:1994 3.6 basic semantic unit BSU entity that provid
43、es an absolute and universally unique identification of certain objects of the application domain (e.g. classes, data element types) ISO 13584-42 3.7 conformance class subset of a standard for which conformance may be claimed ISO 13584-24:2003 3.8 conformance requirement precise, text definition of
44、a characteristic required to be present in a conforming implementation ISO 10303-1:1994 3.9 conforming implementation implementation which satisfies the conformance requirements defined by one or several conformance classes of a standard ISO 13584-24:2003 3.10 conformity conformance fulfilment by th
45、e implementation of all specified requirements ISO 10303-31:1994 3.11 entity (data type) instance named unit of data that represents a unit of information within the class defined by an entity, and which is a member of the domain established by an entity data type ISO 10303-11:1994 ISO 13584-102:200
46、6(E) 4 ISO 2006 All rights reserved3.12 functional model of a part information model of one representation category of a part in an integrated library ISO 13584-1:2001 3.13 functional view of a part information model of one representation category of a part in product data ISO 13584-1:2001 NOTE The
47、structure of a functional view does not depend on the part it represents. 3.14 implementation method technique used by computers to exchange data that is described using the EXPRESS data specification language ISO 13584-24:2003 3.15 implementation resources capabilities of a software system that sha
48、ll be available to claim conformance to a particular conformance class of a view exchange protocol or both view exchange protocol and library integrated information model ISO 13584-24:2003 3.16 information model formal model of a set of facts, concepts or instructions to meet a specific requirement
49、ISO 10303-1:1994 3.17 integrated library operational system consisting of a library management system and a user library ISO 13584-24:2003 3.18 library see: parts library (3.25), supplier library (3.31), and user library (3.32) ISO 13584-1:2001 3.19 library data supplier organisation that delivers a supplier library in the standard format defined in ISO 13584 and is r
