1、 Reference number ISO 12633-1:2011(E) ISO 2011INTERNATIONAL STANDARD ISO 12633-1 First edition 2011-09-15 Hot-finished structural hollow sections of non-alloy and fine grain steels Part 1: Technical delivery conditions Profils creux de construction finis chaud, en acier non alli ou grains fins Parti
2、e 1: Conditions techniques de livraison ISO 12633-1:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, wi
3、thout permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All r
4、ights reservedISO 12633-1:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv 1 Scope 1 2 Normative references 1 3 Terms and definitions . 2 4 Classification and designation 2 4.1 Classification . 2 4.2 Designations 3 5 Information to be supplied by the purchaser . 4 5.1 Mandatory info
5、rmation 4 5.2 Options . 4 5.3 Example 5 6 Requirements . 5 6.1 General . 5 6.2 Steel manufacturing process . 5 6.3 Structural hollow section manufacturing process 6 6.4 Delivery conditions . 6 6.5 Chemical composition 6 6.6 Mechanical properties . 8 6.7 Technological properties 8 6.8 Surface conditi
6、on 9 6.9 Non-destructive testing of welds . 9 6.10 Tolerances and mass 9 7 Inspection . 10 7.1 Types of inspection and testing 10 7.2 Types of inspection documentation 10 7.3 Inspection and testing 11 8 Samples 12 8.1 Frequency of tests . 12 8.2 Preparation of samples and test pieces 13 9 Test metho
7、ds . 14 9.1 Chemical analysis . 14 9.2 Mechanical tests 14 9.3 Visual examination and dimensional inspection . 15 9.4 Non-destructive testing 15 9.5 Retests, sorting and reprocessing 16 10 Marking . 16 Annex A (normative) Structural hollow sections of non-alloy steels Chemical composition and mechan
8、ical properties 17 Annex B (normative) Structural hollow sections of fine grain steels Chemical composition and mechanical properties 19 Annex C (normative) Location of samples and test pieces for hollow sections 21 Bibliography 24 ISO 12633-1:2011(E) iv ISO 2011 All rights reservedForeword ISO (the
9、 International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committe
10、e has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechni
11、cal standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member b
12、odies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying a
13、ny or all such patent rights. ISO 12633-1 was prepared by Technical Committee ISO/TC 5, Ferrous metal pipes and metallic fittings, Subcommittee SC 1, Steel tubes. This first edition cancels and replaces ISO 630-2:2000, of which it constitutes a minor revision. In particular, better grouping of sever
14、al documents by subject area and minor editorial improvements have been carried out. In addition, reference number ISO 630-2 has been utilized for a new subject: technical delivery conditions for structural steels for general purposes. ISO 12633 consists of the following parts, under the general tit
15、le Hot-finished structural hollow sections of non-alloy and fine grain steels: Part 1: Technical delivery conditions Part 2: Dimensions and sectional properties INTERNATIONAL STANDARD ISO 12633-1:2011(E) ISO 2011 All rights reserved 1Hot-finished structural hollow sections of non-alloy and fine grai
16、n steels Part 1: Technical delivery conditions 1 Scope This part of ISO 12633 specifies the technical delivery requirements for hot-finished hollow sections of circular, square or rectangular form. It is applicable to hollow sections formed hot with or without subsequent heat treatment or formed col
17、d with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot-formed product. Fine grain steels are generally delivered in the normalized condition. The grades, chemical composition and mechanical properties for non-alloy steels and fine grain steels are
18、 given in Annexes A and B, respectively. NOTE 1 For the requirements for tolerances, dimensions and sectional properties, see ISO 12633-2. NOTE 2 For the technical delivery requirements of hot-rolled structural steels in other product forms, e.g. plates, wide strip, flats, bars and other structural
19、sections, see ISO 630-1 and ISO 630-2. NOTE 3 For cold-formed structural hollow sections, see ISO 10799-1 and ISO 10799-2. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undat
20、ed references, the latest edition of the referenced document (including any amendments) applies. ISO 148-1, Metallic materials Charpy pendulum impact test Part 1: Test method ISO 377, Steel and steel products Location and preparation of samples and test pieces for mechanical testing ISO 404, Steel a
21、nd steel products General technical delivery requirements ISO 643, Steels Micrographic determination of the apparent grain size ISO 2566-1, Steel Conversion of elongation values Part 1: Carbon and low alloy steels ISO 6892-1, Metallic materials Tensile testing Part 1: Method of test at room temperat
22、ure ISO 6892-2, Metallic materials Tensile testing Part 2: Method of test at elevated temperature ISO 9606-1, Qualification testing of welders Fusion welding Part 1: Steels ISO 10474:1991, Steel and steel products Inspection documents ISO 12633-1:2011(E) 2 ISO 2011 All rights reservedISO 10893-2, No
23、n-destructive testing of steel tubes Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections ISO 10893-3, Non-destructive testing of steel tubes Part 3: Automated full peripheral flux leakage testing of seamless and w
24、elded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections ISO 10893-6, Non-destructive testing of steel tubes Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections ISO 10893-11, Non
25、-destructive testing of steel tubes Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections ISO 12633-2, Hot-finished structural hollow sections of non-alloy and fine grain steels Part 2: Dimensions and sectional
26、properties ISO 14284, Steel and iron Sampling and preparation of samples for the determination of chemical composition ISO 15607, Specification and qualification of welding procedures for metallic materials General rules ISO 15609-1, Specification and qualification of welding procedures for metallic
27、 materials Welding procedure specification Part 1: Arc welding ISO 15614-1, Specification and qualification of welding procedures for metallic materials Welding procedure test Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys 3 Terms and definitions For the purposes o
28、f this document, the following terms and definitions apply. 3.1 tube hollow long product open at both ends of any cross-sectional shape 3.2 structural hollow section tube intended to be used for structural purposes 3.3 normalizing rolling rolling process in which the final deformation is carried out
29、 in a certain temperature range leading to a material condition equivalent to that obtained after normalizing so that the specified values of the mechanical properties are retained even after normalizing 4 Classification and designation 4.1 Classification 4.1.1 Within the steel grades of the non-all
30、oy steels given in Annex A, three qualities JR, J0, and J2 are specified. These qualities differ with respect to specified impact requirements, method of deoxidation, and limits on values of various elements, with particular reference to sulfur and phosphorus, and inspection and testing requirements
31、. 4.1.2 Within the steel grades of the fine grain steels given in Annex B, two qualities, N and NL, are specified. These differ in respect of the carbon, sulfur and phosphorus content and low-temperature impact properties. ISO 12633-1:2011(E) ISO 2011 All rights reserved 34.2 Designations 4.2.1 For
32、non-alloy steel structural hollow sections, the steel designation consists of: a reference to this part of ISO 12633, i.e. ISO 12633-1:2011; the capital letter S for structural steel; the indication of the minimum specified yield strength for thicknesses 16 mm, expressed in newtons per square millim
33、etre (N/mm 2 ); the capital letters JR for the qualities with specified impact properties at room temperature; the capital letter J and a number 0 or 2 for the qualities with specified impact properties at 0 C and 20 C respectively; the capital letter H to indicate hollow sections. 4.2.2 For fine gr
34、ain steel structural hollow sections, the steel designation consists of: a reference to this part of ISO 12633, i.e. ISO 12633-1:2011; the capital letter S for structural steel; the indication of the minimum specified yield strength for thicknesses 16 mm, expressed in newtons per square millimetre (
35、N/mm 2 ); the capital letter N to indicate normalized or normalized rolled (see 6.4); the capital letter L for the qualities with specified minimum values of impact energy at a temperature of 50 C; the capital letter H to indicate hollow sections. 4.2.3 For modification of the designations in case o
36、f special delivery conditions, see 6.4. 4.2.4 The steel shall be designated as illustrated by the following examples: EXAMPLE 1 ISO 12633-1:2011(E) 4 ISO 2011 All rights reservedEXAMPLE 2 NOTE Steel names used in this part of ISO 12633 differ from those in ISO/TS 4949. 5 Information to be supplied b
37、y the purchaser 5.1 Mandatory information The following information shall be supplied by the purchaser at the time of enquiry and order: a) the quantity (mass or total length or number); b) the type of length and length range or length (see ISO 12633-2); c) details of the product form: HFCHS = hot-f
38、inished circular hollow sections; HFRHS = hot-finished square or rectangular hollow sections; d) the steel designation (see 4.2); e) the dimensions (see ISO 12633-2); f) the options required (see 5.2); g) the type of inspection document required (see 7.2 and Tables 2 and 3). 5.2 Options A number of
39、options are specified in this part of ISO 12633; they are listed in this subclause with the appropriate clause references. In the event that the purchaser does not indicate his/her wish to implement any of these options at the time of enquiry and order, the products shall be supplied in accordance w
40、ith the basic specification (see 5.1). a) Option 1: product analysis shall be carried out (see 6.5.1). b) Option 2: a maximum carbon equivalent value (CEV) in accordance with Table A.2 shall be provided for non-alloy grades (see 6.5.2). c) Option 3: the Cr, Cu, Mo, Ni, Ti and V cast analysis content
41、s shall be reported in the inspection certificate or inspection report for non-alloy grades (see 6.5.2). d) Option 4: a maximum carbon equivalent value in accordance with Table B.2 shall be provided for fine grain steels S275 and S355 (see 6.5.3). ISO 12633-1:2011(E) ISO 2011 All rights reserved 5e)
42、 Option 5: the cast analysis limits for grade S460 (see 6.5.3) shall be: 1) V + Nb + Ti 0,22 %; and 2) Mo + Cr 0,30 %. f) Option 6: impact properties of quality J0 and JR shall be verified by test. This option applies only when products are ordered with specific inspection and testing (see 6.6.4). g
43、) Option 7: the material shall be suitable for hot dipped galvanized coating (see 6.7.2). h) Option 8: weld repairs to the body of non-alloy structural steel hollow sections shall not be permitted (see 6.8.4). i) Option 9: specific inspection and testing for non-alloy grades of qualities JR and J0 s
44、hall be applied (see 7.1.1). 5.3 Example 6 Requirements 6.1 General Structural hollow sections of non-alloy steels shall comply with the requirements of Annex A; structural hollow sections of fine grain steels shall comply with the requirements of Annex B. 6.2 Steel manufacturing process 6.2.1 The s
45、teel manufacturing process shall be at the discretion of the steel producer. 6.2.2 For the non-alloy structural steels given in Annex A, the method of deoxidation shall be as given in Table A.1. 6.2.3 For the fine grain steels given in Annex B, the method of deoxidation shall be as given in Table B.
46、1. 6.2.4 The fine grain steels given in Annex B shall have a ferritic grain size equal to or finer than 6 when measured in accordance with ISO 643. ISO 12633-1:2011(E) 6 ISO 2011 All rights reserved6.3 Structural hollow section manufacturing process 6.3.1 Structural hollow sections shall be manufact
47、ured by a seamless or by a welding process. Welded sections manufactured by a continuous process shall not include welds used for joining lengths of the flat rolled-strip prior to forming the hollow section, except as permitted in 9.4.3. 6.3.2 Electric welded hollow sections are normally supplied wi
48、thout trimming the internal weld bead. 6.3.3 For quality assurance requirements, see ISO 404. If the purchaser specifies quality assurance, an appropriate International Standard, such as ISO 9001, can be used. 6.4 Delivery conditions 6.4.1 The hollow sections shall be delivered in the following cond
49、itions: qualities JR, J0 and J2: hot-finished; qualities N and NL: normalized (normalized includes normalized rolled). 6.4.2 It may be necessary for seamless hollow sections with a wall thickness above 16 mm or when T/D is greater than 0,15 to apply accelerated cooling after austenitizing to achieve the intended structure or liquid quenching and tempering to achieve the mechanical properties. The decision shall be left to the discretion of the
