1、 ISO 2014 Agricultural tractors Requirements for steering AMENDMENT 1 Tracteurs agricoles Exigences relatives la conduite AMENDEMENT 1 INTERNATIONAL STANDARD ISO 10998 Second edition 2008-06-01 Reference number ISO 10998:2008/Amd.1:2014(E) AMENDMENT 1 2014-02-01 ISO 10998:2008/Amd.1:2014(E)ii ISO 20
2、14 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet,
3、without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Publishe
4、d in Switzerland ISO 10998:2008/Amd.1:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each mem
5、ber body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International El
6、ectrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different type
7、s of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be
8、held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is informa
9、tion given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the
10、 following URL: Foreword - Supplementary information The committee responsible for this Amendment 1 to ISO 10998:2008 was Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tractors. ISO 2014 All rights reserved iii Agricultural tractors Requiremen
11、ts for steering AMENDMENT 1 Page 2, Clause 3.1.5 Delete Clause 3.1.5. Page 9, Clause 5.4.1.5 Add the following sentence as the last sentence of Clause 5.4.1.5: “This provision does not apply to track-laying tractors (e.g. differential, articulated, and combination wheeled and track-laying tractors).
12、” Page 9, Clause 5.4.16 Add the following sentence as the last sentence of Clause 5.4.1.6: “This provision does not apply to track-laying tractors (e.g. differential, articulated, and combination wheeled and track-laying tractors).” Page 12, Clause 5.8.1.2 Replace the existing text by the following:
13、 “The performance of the steering equipment shall not be adversely affected by electromagnetic disturbances according to ISO 14982.” Page 12, Clause 5.8.2.1 Replace the existing text by the following: “Testing and verification shall be in accordance with Annex A.4.” Page 14, Annex A, Clause A.3.1 Re
14、place the existing text of the first paragraph by the following: “When legally required, the manufacturer shall develop and maintain a documentation package which gives access to the basic design of “the system” and the means by which it is linked to other tractor systems or by which it directly controls output variables.” ISO 10998:2008/Amd.1:2014(E) ISO 2014 All rights reserved 1 ISO 10998:2008/Amd.1:2014(E) ISO 2014 All rights reserved IC S 65.060.10 Price based on 1 page
