1、STD-IS0 10497-ENGL L991 4853903 0733503 477 D INTERNATIONAL STANDARD IS0 10499:199E TECHNICAL CORRIGENDUM 1 Published 1997-1 2-1 5 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MEXQYHAPOUHAA OPiAHH3AUMR no CTAHDAPTH3AUMM ORGANISATION INTERNATIONALE DE NORMALISATION Industrial tyres and rims - Soli
2、d tyres (metric series) for pneumatic tyre rims - Designation, dimensions and marking TECHNICAL CORRIGENDUM 1 Pneumatiques et jantes pour matriel de manutention - Bandages pleins (srie millimtrique) pour jantes de pneumatiques - Dsignation, cotes et marquage RECTIFICATIF TECHNIQUE 1 Technical Corrig
3、endum 1 to International Standard IS0 10499:1991 was prepared by Technical Committee ISO/TC 31, Tyres, rims and valves, Subcommittee SC 7, Industrial tyres and rims. This material is reproduced from IS0 documents under International Organization for Standardization (ISO) Copyright License number IHS
4、IICCI1996. Not for resale. No part of these IS0 documents may be reproduced in any form, electronic retrieval system or otherwise, except as allowed in the copyright law of the country of use, or with the prior written consent of IS0 (Case postale 56,1211 Geneva 20, Switzerland, Fax +41 22 734 10 79
5、), IHS or the IS0 Licensors members. Page i, top and bottom; pages i to 3, headers Change the reference number of the document to IS0 10499-1 :1991. Pages i and 7 Title Change the title to read as follows: “Industrial tyres and rims - Rubber solid tyres (metric series) for pneumatic tyre rims - Part
6、 1: Designation, dimensions and marking” ICs 83.160.99 Ref. No. IS0 10499:1991/Cor.l:1997(E) Descriptors: machinery, machine components, tyres, rims, specifications, dimensions designation, marking. I O IS0 1997 Printed in Switzerland STD-IS0 3OLI91-ENGL L99L = 4853903 0733504 323 IS0 10499:1991/Cor
7、.l:1997(E) IS0 Page I Clause 2 Add the following normative reference: IS0 10499-2:-, Industrial tyres and rims - Rubber solid tyres (metric series) for pneumatic tyre rims - Part 2: Load ratings. (To be published.) Page 2 Clause 5 Change the first sentence to read as follows: The marking concerning
8、the dimensional and constructional characteristics shall consists of the four-part designation specified in clause 4.” Add the following after the last sentence: The marking concerning the designation of the service description is specified in IS0 10499.2:-.” 2 - IS0 LO499 91 W 4853903 OL09838 L I N
9、 TE R NAT I O NA L STANDARD IS0 First edition 1991-09-15 Industrial tyres and rims - Solid tyres (metric series) for pneumatic tyre rims - Designatin, dimensions and marking Pneumatiques et jantes pour matriel de manutention - Bandages pleins (srie millimtrique) pour jantes de pneumatiques - Dsignat
10、ion, cotes et marquage Reference number IS0 10499:1991 (E) 1 IS0 10499 91 4851903 0109839 3 IS0 10499:1991 (E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards I
11、s normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern- mental and non-governmental, in liaison with ISO, also take p
12、art in the work. IS0 collaborates closely with the International Electrotechnicaf Commission (IEC) on all matters of electrotechnical standardization, Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Inter- national S
13、tandard requires approval by at least 75% of the member bodies casting a vote. International Standard IS0 10499 was prepared by Technical Committee ISO/TC 31, Tyres, rims and valves, Sub-Committee SC 7, Industrial fyres and rims. o IC0 1991 All rlghts reserved, No part of thls publlcatlon may be rep
14、roduced or utlllzed In any form or by any means, electronic or mechanlcal, Includlng photocopylng and microfilm, wlthout permlsslon in wriflng from the publisher. International Organizatlon for Standardlzatlon Case Postale 56 CH-I211 Genve 20 Switzerland Prlnted In Swltzerland ii IS0 10497 91 485190
15、3 0109840 T Nominal rim diameter INTERNATIONAL STANDARD IS0 10499:1991 (E) Nominal rim diameter, I), Industrial tyres and rims - Solid tyres (metric series) for pneumatic tyre rims - Designation, dimensions and marking 1 Scope This International Standard specifies the main re- quirements, including
16、designations, dimensions and markings, of the metric series of rubber solid tyres for pneumatic tyre rims primarily intended for in- dustrial machines for use on prepared surfaces. Rim contours fitting these tyres will be specified in a future part of IS0 3739. 2 Normative references The following s
17、tandards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publi- cation, the editions indicated were valid. All stan- dards are subject to revision, and parties to agreements based on this International Standard are encour
18、aged to investigate the possibility of ap- plying the most recent editions of the standards in- dicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 3739-1:-1), Industrial tyres and rims - Part I: Pneumatic tyres (mefric series) on 5 degrees tapere
19、d or flat base rims - Designation, dimensions and marking. IS0 3877-4:1984, Tyres, valves and tubes - List of equivalent terms - Part 4: Solid tyres. IS0 4223-2:1991, Definitions of some terms used in the tyre industry - Part 2: Solid fyres. 3 Definitions For definitions of terms relating to solid t
20、yres, see IS0 4223-2; equivalent terms are given in IS0 3877-4. 4 Tyre designations The dinlensional and constructional characteristics shall be indicated as follows: NomInal NomInal NomInal aspect - rlm dlameter rlm wldth wldth ratlo code I code 4.1 Nominal section width The nominal section width o
21、f tlie tyre shall be indi- cated in millimetres, ending either in O or 5. 4.2 NomInal aspect ratio The nominal aspect ratio shall be expressed as a percentage and shall be a multiple of 5. 4.3 Nominal rim diameter code For tyres mounted on existing rims, the code shall be as given in table 1. mm I c
22、ode 4 6 8 9 10 12 15 102 152 203 229 254 305 38 I 1) To be published. .1 IS0 10499 91 = 4851903 0109841 1 IS0 10499:1991(E) 4.4 Nominal rim width code For tyres mounted on existing rims, the code shall be as given in table2. Table 2 - Nominal rim width code Nominal rim width code 2.5 3.25 4.0 5.0 6.
23、5 8.0 10.0 5 Marking The marking shall consist of the four-part desig- nation specified in clause 4. The location of the marking of the rim width code may be distinct but shall be in close proximity to the marking of the other dimensional characteristics. EXAMPLE 225175 - 1516.5 The characteristics
24、of a tyre with the above markings would be as follows: 225: nominal section width equal to 225 mm; 75: nominal aspect ratio equal to 75; 15: nominal rini diaineter code, corresponding to 381 mm; 6.5: nominal rim width code. 6 Tyre dimensions The specified dimensional data for solid tyres for pneumat
25、ic tyre rims are maximum dimensions and shall satisfy the requirements in 6.1 and 6.2. 6.1 The tyre section width shall not exceed the values of design section width for pneumatic tyres of the same size designatioti as specified in IS0 3739-1. The effective tyre section width of the solid tyres may
26、be substantially less than the specified design section width. 6.2 The tyre section height shall not exceed the values of design section height for pneumatic tyres of the same size designation as specified in The tyre overall diameter is the sum of the nominal rim diameter, Dr, plus twice the tyre s
27、ection height. IS0 3739-1. 7 Tyre size range The relevant size range for the recommended metric series of solid tyres for pneumatic tyre rims and their specified maximum dimensions are shown in table 3. 2 IS0 30499 93 4853903 0309842 3- I Rim width code Maximum tyre sectlon width mm . 100 110 125 14
28、0 160 180 200 4 4 4 4 4 4 4 292 306 328 348 376 404 432 343 357 379 399 427 455 483 519 282 296 314 334 360 386 41 2 333 347 365 385 41 1 437 463 495 1 O0 110 125 140 160 200 225 180 8 8 8 8 8 8 8 a 405 425 453 48 1 509 545 39 I 41 1 437 463 489 52 1 478 506 534 570 604 646 529 557 585 62 1 655 697
29、747 462 488 514 546 580 618 51 3 539 565 597 63 1 669 715 4.0 5.0 5.0 6.5 6.5 8.0 8.0 156 180 195 228 246 283 308 160 180 200 225 250 280 315 355 15 15 15 i5 15 15 15 15 605 633 66 1 697 73 I 773 823 879 589 615 64 1 673 707 745 79 1 843 IS0 10499:1991 (E) Table 3 - Recommended size range and dimens
30、ions for solid tyres for pneumatic tyre riins Maximum overall diameter min Nomiiial aspect ratio 75 Yo I mm 85 % 272 290 314 340 374 408 442 322 340 364 390 424 458 492 373 39 1 415 44 1 475 509 543 585 44 1 467 50 1 535 569 61 1 526 560 594 636 680 730 80 Yo 262 278 302 326 358 390 422 2.5 3.25 3.2
31、5 4.0 4.0 5.0 5.0 98 112 123 141 156 180 195 252 268 290 312 342 372 402 326 310 354 336 382 2.5 I 98 312 328 352 376 408 440 472 302 318 340 362 392 422 452 353 369 391 41 3 443 473 503 54 1 1 O0 110 125 140 160 180 200 3.25 If2 3.25 1 123 4.0 141 4.0 i 56 5.0 5.0 363 379 403 427 459 49 1 523 563 2
32、.5 3.25 3.25 4.0 4.0 5.0 5.0 6.5 98 112 123 141 156 180 195 228 3.25 4. O 4.0 5.0 5.0 6.5 123 141 156 180 195 228 429 453 485 517 549 589 417 439 469 499 529 567 125 140 160 180 200 225 10 10 10 10 10 10 4.0 5.0 5.0 6.5 6.5 8.0 156 180 193 228 246 283 51 O 542 574 614 654 702 56 I 593 625 665 705 75
33、3 809 - 494 524 554 592 630 674 545 575 605 643 68 1 725 777 160 180 200 225 250 280 12 12 12 12 12 12 12 577 61 1 645 687 73 I 781 841 160 180 200 225 . 250 280 315 4.0 5.0 5.0 6.5 6.5 8.0 8.0 10.0 156 180 195 228 246 283 308 357 637 669 70 1 74 1 781 829 885 949 621 651 68 1 719 757 80 1 853 913 653 687 72 1 763 807 8 57 917 985 UDC 629.11.012.53:62-182.3 Descriptors: machlnery, machine components, tyres, rims, speclficationc, dimensions, deslgnation, marking. Price based on 3 pages
