1、 IEEE Guide for In-Service Use, Care, Maintenance, and Testing of Conductive Clothing for Use on Voltages up to 765 kV AC and 750 kV DC Sponsored by the Transmission and Distribution Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA 16 January 2013 IEEE Power and Energy Society IEEE Std 1067-
2、2012 (Revision of IEEE 1067-2005) IEEE Std 1067-2012 (Revision of IEEE Std 1067-2005) IEEE Guide for In-Service Use, Care, Maintenance, and Testing of Conductive Clothing for Use on Voltages up to 765 kV AC and 750 kV DC Sponsor Transmission and Distribution Committee of the IEEE Power and Energy So
3、ciety Approved 5 December 2012 IEEE-SA Standards Board Abstract: General recommendations for the in-service care, maintenance, and testing of the conductive clothing worn by workers to perform work in high-voltage fields are presented. Keywords: clothing, conductivity, energized, IEEE 1067, maintena
4、nce, power lines The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2013 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 16 January 2013. Printed in the United States of America. IEEE is a re
5、gistered trademark in the U.S. Patent +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Copyright 2013 IEEE. All rights reserved. iv Notice to users Laws and regulations Users of IEE
6、E Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regul
7、atory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights This document is copyrighted by the IEEE. It is made available for a wide variety of both pub
8、lic and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making this document available for use and adoption by public authorities and private users, the IEEE d
9、oes not waive any rights in copyright to this document. Updating of IEEE documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda,
10、or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of
11、amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/standards.ieee.org/index.html or contact the IEEE at the address listed previously. For more information about the IEEE Standards Association or the IEEE standards development process, visit IEEE-SA Website at http:/standards.ieee
12、.org/index.html. Errata Errata, if any, for this and all other standards can be accessed at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Copyright 2013 IEEE. All rights reserved. v Patents Attention is called
13、to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent a
14、pplicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under pat
15、ent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is
16、 not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any,
17、 or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the
18、IEEE Standards Association. Copyright 2013 IEEE. All rights reserved. vi Participants At the time this IEEE guide was completed, the 15.07.05.02 Standards Working Group had the following membership: Lawrence D. Schweitzer, Chair Robert Bendall K. J. Brown Kristine K. Buchholz Thomas Buonincontri J.
19、Christensen E. Davis D. J. Dodds J.F.Doering B. Erga George Gela Charles W. Grose Alan Holloman Edward Hunt E. Jones Clayton King N. Kolcio T. D. Rasler George E. Stinnett R. Sundararajan James Tomaseski T. Verdecchio The following members of the individual balloting committee voted on this guide. B
20、alloters may have voted for approval, disapproval, or abstention. William Ackerman David Baron Gernot Brandt Thomas Buonincontri Arvind K Chaudhary Gary Donner Gary Engmann George Gela Mietek Glinkowski Edwin Goodwin Charles W. Grose Randall Groves Lee Herron Werner Hoelzl Edward Hunt Joseph L. Koep
21、finger Jim Kulchisky Saumen Kundu Chung-Yiu Lam Greg Luri Tim Olson Carl Orde Bansi Patel Percy Pool Bartien Sayogo Lawrence Schweitzer Gil Shultz James Smith Jerry Smith John Spare Gary Stoedter James Tomaseski John Toth John Vergis Edward West Larry Young When the IEEE-SA Standards Board approved
22、this guide on 5 December 2012, it had the following membership: Richard H. Hulett, Chair John Kulick, Vice Chair Robert M. Grow, Past Chair Konstantinos Karachalios, Secretary Satish Aggarwal Masayuki Ariyoshi Peter Balma William Bartley Ted Burse Clint Chaplin Wael Diab Jean-Philippe Faure Alexande
23、r Gelman Paul Houz Jim Hughes Joseph L. Koepfinger* David J. Law Thomas Lee Hung Ling Oleg Logvinov Ted Olsen Gary Robinson Jon Walter Rosdahl Sam Sciacca Mike Seavey Yatin Trivedi Phil Winston Don Wright *Member Emeritus Copyright 2013 IEEE. All rights reserved. vii Also included are the following
24、nonvoting IEEE-SA Standards Board liaisons: Richard DeBlasio, DOE Representative Michael Janezic, NIST Representative Patrick Gibbons IEEE Standards Program Manager, Document Development Erin Spiewak IEEE Standards Program Manager, Technical Program Development Copyright 2013 IEEE. All rights reserv
25、ed. viii Introduction This introduction is not part of IEEE Std 1067-2012, IEEE Guide for In-Service Use, Care, Maintenance, and Testing of Conductive Clothing for Use on Voltages up to 765 kV AC and 750 kV DC. Conductive clothing minimizes discomfort due to the electric field by providing a shield
26、around the workers body. The original development and testing of conductive suits dates back to the early 1960s. The success of these suits in relieving the worker from discomfort while working on lines up through 765 kV ac and 750 kV dc has played an important role in the successful operation, main
27、tenance, and continuity of service of these extremely high-voltage (EHV) lines. A number of member companies within IEEEs Engineering in the Safety, Maintenance, and Operations of Lines (ESMOL) Subcommittee made it known that an in-service guide was needed to inspect and test conductive suits before
28、 a worker went up to the energized conductor. Prior to drafting the first publication of this guide, a survey of the user community was conducted to deter-mine if such a guide was needed and also to solicit user procedures for the purpose of sharing information. It was evident that little technical
29、information was available. It was also learned, however, that information was needed. ESMOL was encouraged to research the subject and to summarize its findings in a guide. This guide was revised to reflect advancements in the manufacturing and testing of conductive clothing. It is intended that the
30、 contents of this guide will be modified as future needs dictate. Suggestions for improvements and additions are welcome. Copyright 2013 IEEE. All rights reserved. ix Contents 1. Overview 1 1.1 Scope . 1 1.2 Purpose 2 2. Normative references 2 3. Technical considerations 2 3.1 General 2 3.2 Suits, j
31、ackets, and trousers . 2 3.3 Conductive boots . 4 3.4 Conductive gloves . 4 3.5 Leather gloves 4 3.6 Conductive socks . 4 4. Care of conductive clothing 5 4.1 General 5 4.2 Storage . 5 4.3 Cleaning . 5 5. Patching and repair of conductive clothing 5 6. Visual inspection before use (field testing) 6
32、6.1 General 6 6.2 Clothing . 6 6.3 Bonding strap continuity check . 7 7. Periodic nondestructive testing (laboratory or field) 7 7.1 General 7 7.2 Resistance testing method 7 7.3 Screening efficiency testing method 9 7.4 Test frequency 11 8. Record keeping 12 Annex A (informative) Stickman diagram .
33、13 Annex B (informative) Sample test reports 14 Annex C (informative) Worker conductive suit questionnaire (used with sample data sheet) .16 Annex D (informative) Bibliography .17 Copyright 2013 IEEE. All rights reserved. 1IEEE Guide for In-Service Use, Care, Maintenance, and Testing of Conductive C
34、lothing for Use on Voltages up to 765 kV AC and 750 kV DC IMPORTANT NOTICE: IEEE Standards documents are not intended to ensure safety, health, or environmental protection, or ensure against interference with or from other devices or networks. Implementers of IEEE Standards documents are responsible
35、 for determining and complying with all appropriate safety, security, environmental, health, and interference protection practices and all applicable laws and regulations. This IEEE document is made available for use subject to important notices and legal disclaimers. These notices and disclaimers a
36、ppear in all publications containing this document and may be found under the heading “Important Notice” or “Important Notices and Disclaimers Concerning IEEE Documents.” They can also be obtained on request from IEEE or viewed at http:/standards.ieee.org/IPR/disclaimers.html. 1. Overview 1.1 Scope
37、This guide provides recommendations for the in-service visual inspection, use, care, maintenance, and electrical testing of conductive clothing, including suits, gloves, socks, and boots, for use during linework on voltages up to 765 kV ac and 750 kV dc. Testing pertains only to nondestructive elect
38、rical tests that can be performed periodically to check if there is any reduction in the conductivity of the clothing. IEEE Std 1067-2012 IEEE Guide for In-Service Use, Care, Maintenance, and Testing of Conductive Clothing for Use on Voltages up to 765 kV AC and 750 kV DC Copyright 2013 IEEE. All ri
39、ghts reserved. 2 1.2 Purpose The purpose of this guide is to present, in one document, sufficient details of presently used methods and techniques to provide for inspection, care, maintenance, and field testing. This guide also presents a new method of testing conductive clothing. This guide is inte
40、nded to direct attention to appropriate standards and regulations relating to the care or testing of conductive clothing. It is not intended that this guide should replace present proven company procedures, nor imply that these recommendations are superior to existing practices and therefore should
41、be universally adopted as company standards. This compilation of many accepted practices is presented specifically in the form of a guide to be used by those utilities that are seeking guidance in establishing methods and procedures for the use, care, maintenance, and testing of conductive clothing.
42、 2. Normative references The following referenced documents are indispensable for the application of this document (i.e., they must be understood and used, so each referenced document is cited in text and its relationship to this document is explained). For dated references, only the edition cited a
43、pplies. For undated references, the latest edition of the referenced document (including any amendments or corrigenda) applies. ANSI/SIA A92.2-2001, Vehicle-Mounted Elevating and Rotating Aerial Devices.13. Technical considerations 3.1 General Conductive clothing is used to minimize discomfort due t
44、o the electric field associated with extremely high-voltage (EHV) line work by providing an electrical shield around the workers body. During barehand work, the worker is bonded to the conductor or device to keep the worker at the same potential. The wearer should be made responsible for the care an
45、d condition of the conductive clothing. Training should be provided in the inspection and care of conductive clothing. 3.2 Suits, jackets, and trousers Conductive suits (see Figure 1) should be the outermost garment at all times, except that leather protective gloves can be worn over the conductive
46、gloves for protection from mechanical damage (see 3.5). 1ANSI publications are available from the Sales Department, American National Standards Institute, 25 West 43rd Street, 4th Floor, New York, NY 10036, USA (http:/www.ansi.org/). IEEE Std 1067-2012 IEEE Guide for In-Service Use, Care, Maintenanc
47、e, and Testing of Conductive Clothing for Use on Voltages up to 765 kV AC and 750 kV DC Copyright 2013 IEEE. All rights reserved. 3 WARNING Do not wear other clothing over conductive clothing. Clothing worn over conductive clothing may burn when conduction occurs, and burning can result in serious i
48、njury or death to both the wearer and coworkers. Figure 1 Proper wearing of the suit IEEE Std 1067-2012 IEEE Guide for In-Service Use, Care, Maintenance, and Testing of Conductive Clothing for Use on Voltages up to 765 kV AC and 750 kV DC Copyright 2013 IEEE. All rights reserved. 4 When dressed in c
49、onductive clothing, it is important that all the different pieces of conductive clothing are well bonded together. This can be verified by a second worker. Trousers and jackets from different manufacturers may be interchanged so long as they are of the same generic fabric type. However, if there is discomfort, clothing of the same manufacturer should be used. If discomfort persists, the suit should be inspected and tested. Conductive socks worn with conductive clothing will properly bond the worker through the soles of the conductive boots. If b
