欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM C1103-2019 Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines.pdf

    • 资源ID:1243448       资源大小:53.48KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM C1103-2019 Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines.pdf

    1、Designation: C1103 14C1103 19Standard Practice forJoint Acceptance Testing of Installed Precast Concrete PipeSewer Lines1This standard is issued under the fixed designation C1103; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

    2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers procedures for testing the joints of installed precast concrete pipe sewer lines, when u

    3、sing either airor water under low pressure to demonstrate the integrity of the joint and the construction procedures. This practice is used fortesting 27-in. and larger diameter precast concrete sewer lines utilizing rubber gasket sealed joints.NOTE 1The user of this practice is advised that methods

    4、 described herein may also be used as a preliminary test to enable the manufacturer or installerto demonstrate the condition of sewer pipe prior to delivery.1.2 This practice is the inch-pound companion to Practice C1103M; therefore, no SI equivalents are presented in the practice.NOTE 2The owner sh

    5、all specify the following: who will conduct, observe, and furnish labor, material, and measuring devices and pay for the tests;who is responsible for determining local ground conditions; and whether an air or water test is to be used.NOTE 3The user of this practice is advised that test criteria pres

    6、ented in this practice are similar to those in general use. Pipe shall be accepted byinfiltration or exfiltration testing utilizing Practice C969.NOTE 4Test times tabulated and the rate of air loss in this practice are based on successful testing of installed pipelines. However, since air and waterh

    7、ave different physical properties, retests of some pipelines not meeting field air tests have been successful when tested with water.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to esta

    8、blish appropriate safety safety, health, and healthenvironmental practices and determine theapplicability of regulatory limitations prior to use. Specific precautions are given in Section 6.1.4 This international standard was developed in accordance with internationally recognized principles on stan

    9、dardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2C822 Terminology Relating to Concrete Pipe and

    10、Related ProductsC969 Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines3. Terminology3.1 DefinitionsFor definitions of terms relating to concrete pipe, see Terminology C822.4. Summary of Practice4.1 The joint in the sewer line to be tested is

    11、 covered on the inside of the pipe by a ring with two end element sealing tubes.Air or water, at low pressure, is introduced through a connection on the ring into the annular space between the ring and joint. Theamount of air, or water, loss is used to determine the acceptability of the installed se

    12、wer line.5. Significance and Use5.1 This is not a routine test. The values recorded are applicable only to the sewer being tested and at the time of testing.6. Safety Precautions6.1 The use of compressed air is dangerous if a sewer line is not prepared properly and proper procedures are not followed

    13、.6.2 It is imperative that all pressures be relieved completely before the test apparatus is loosened for removal.1 This practice is under the jurisdiction of ASTM Committee C13 on Concrete Pipe and is the direct responsibility of Subcommittee C13.09 on Methods of Test.Current edition approved Nov.

    14、15, 2014Jan. 1, 2019. Published November 2014January 2019. Originally approved in 1989. Last previous edition approved in 20092014as C1103 03C1103 14.(2009). DOI: 10.1520/C1103-14.10.1520/C1103-19.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at

    15、 serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous vers

    16、ion. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM Internation

    17、al, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16.3 Pressurizing lines for the two end element sealing tubes shall be separate from the lines for pressurizing the void volumecreated by the joint test apparatus. The pressures required to seal the end element tu

    18、bes shall be as specified by the apparatusmanufacturer, and are greater than the pressure required to test the joint. The line for pressurizing the void volume shall includea 6-psi pressure relief device to reduce hazards and avoid overpressurization.7. Preparation of the Sewer Joint7.1 Check the si

    19、ze of access openings to ensure that the test apparatus will fit in the sewer line.7.2 Clean the joint and interior joint surfaces to eliminate debris prior to wetting and testing.NOTE 5The user of this practice is advised that a wetted interior surface is desirable and will produce more consistent

    20、results. Air may pass throughthe walls of dry pipe. This can be overcome by wetting the pipe.7.3 Review safety precautions in Section 6.8. Procedures8.1 The following procedures apply to testing with either air or water.8.1.1 Determine groundwater conditions surrounding the sewer line to be tested,

    21、and select the type of test to be conducted.8.1.2 If the groundwater pressure is equal to or greater than the test pressure, and the sewer line or joint is not leaking, the sewerline or joint is acceptable in accordance with Practice C969 and no additional testing is required. If one or more joints

    22、are leaking,but the total amount of leakage in the sewer line being tested is equal to, or less than, the allowable leakage rate established inaccordance with Practice C969, the line is acceptable and no additional testing is required provided visible leaks are repaired.Moisture or beads of water ap

    23、pearing on the surface of the joint will not be considered as visible leakage.8.1.3 Review proper operation, safety, and maintenance procedures as provided by the manufacturer of the joint test apparatus.8.1.4 Move the joint test apparatus into the sewer line to the joint to be tested and position i

    24、t over the joint. Make sure the endelement sealing tubes straddle both sides of the joint and the hoses are attached. For the water test, the bleed-off petcock must belocated at top dead center.8.1.5 Inflate end element sealing tubes with air in accordance with equipment and manufacturers instructio

    25、ns.NOTE 6The user of this practice is advised that all test pressures are measured as gauge pressure, which is defined as any pressure greater thanatmospheric pressure. Since water produces a pressure of 0.43 psi for every foot of depth, test pressures must be increased to offset the depth ofgroundw

    26、ater over the sewer line. If the groundwater level is 2 ft or more above the top of the pipe at the upstream end or if the pressure required forthe test is greater than 6-psi gauge, the joint test method shall not be used and the infiltration test may be used (see Practice C969).NOTE 7An air or wate

    27、r reservoir shall be included in the joint test system. By maintaining a constant supply of air or water in a reservoir, continuouspumping of air or water is not required, and any variances in test equipment and joint space will be negated. The reservoir shall have a minimum volumeof 2.5 ft3.8.2 Joi

    28、nt Air Test:8.2.1 Review procedures in 8.1.8.2.2 Pressurize the void volume with air to 3.5 psi greater than the pressure exerted by groundwater above the pipe. Allow theair pressure and temperature to stabilize before shutting off the air supply, and start of test timing.8.2.3 If pressure holds, or

    29、 drops less than 1 psi in 5 s, the joint is acceptable. Practically, the test is a go/no go test.8.2.4 If the joint being tested fails, it shall be retested, or repaired if necessary, and retested, in accordance with this practice.8.2.5 After the joint test is completed, exhaust void volume, then ex

    30、haust end element tubes prior to removal of apparatus.8.2.6 Use or failure of the joint air test shall not preclude acceptance by appropriate water infiltration and exfiltration testing(see Practice C969), or other means.8.3 Joint Water Test:8.3.1 Review procedures in 8.1.8.3.2 Introduce water into

    31、void volume until water flows evenly from open petcock. Close the petcock and pressurize with waterto 3.5 psi above the pressure exerted by groundwater above the pipe. Shut off the water supply.8.3.3 If the pressure holds, or drops less than 1 psi in 5 s, the joint is acceptable. Practically, the te

    32、st is a go/no go test.8.3.4 If the joint being tested fails, it shall be retested, or repaired if necessary, and retested, in accordance with this practice.8.3.5 After the joint test is completed, exhaust end element tubes which will automatically release the water from the voidvolume, prior to remo

    33、val of apparatus.8.3.6 Use or failure of this joint water test shall not preclude acceptance by appropriate water infiltration or exfiltration testing(see Practice C969), or other means.9. Precision and Bias9.1 No justifiable statement is presently capable of being made either on precision or bias o

    34、f these procedures since the testresults merely state whether this is in conformance to the criteria for success specified. Due to the sealing effects of groundwaterand internal flow on concrete sewer lines, the test conditions and results are not reproducible.C1103 192ASTM International takes no po

    35、sition respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibi

    36、lity.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to AS

    37、TM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address

    38、 shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 193


    注意事项

    本文(ASTM C1103-2019 Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines.pdf)为本站会员(twoload295)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开