1、 IEC 60938-2-2 Edition 1.0 1999-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Fixed inductors for electromagnetic interference suppression Part 2-2: Blank detail specification Inductors for which safety tests are required (only) Inductances fixes dantiparasitage Partie 2-2: Spcification particulire
2、 cadre Inductances ncessitant des essais de scurit (uniquement) IEC 60938-2-2:1999 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 1999 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, e
3、lectronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, plea
4、se contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique,
5、 y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez l
6、e Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepare
7、s and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been
8、published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - w
9、ebstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing mor
10、e than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further
11、assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparen
12、tes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche ava
13、nce vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publ
14、ications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions
15、en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions
16、contactez-nous: csciec.ch. IEC 60938-2-2 Edition 1.0 1999-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Fixed inductors for electromagnetic interference suppression Part 2-2: Blank detail specification Inductors for which safety tests are required (only) Inductances fixes dantiparasitage Partie 2-2
17、: Spcification particulire cadre Inductances ncessitant des essais de scurit (uniquement) INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE J ICS 29.100.10; 31.020 PRICE CODE CODE PRIX ISBN 978-2-83220-772-7 Registered trademark of the International Electrotechnica
18、l Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60938-2-2 IEC:1999 INTERNATIONAL ELECTRO
19、TECHNICAL COMMISSION _ FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION Part 2-2: Blank detail specification Inductors for which safety tests are required (only) FOREWORD 1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all
20、 national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, the IEC publishes International Standa
21、rds. Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC co
22、llaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of op
23、inion on the relevant subjects since each technical committee has representation from all interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical specifications, technical reports or guides
24、 and they are accepted by the National Committees in that sense. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the
25、IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of its standards. 6) Attention is dr
26、awn to the possibility that some of the elements of this International Standard may be the subject of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60938-2-2 has been prepared by IEC technical committee 40: Capacitors a
27、nd resistors for electronic equipment. This bilingual version (2013-05) corresponds to the monolingual English version, published in 1999-10. The text of this standard is based on the following documents: FDIS Report on voting 40/1113/FDIS 40/1139/RVD Full information on the voting for the approval
28、of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 3. Annex A forms an integral part of this standard. 60938-2-2 IEC:1999 3
29、The committee has decided that this publication remains valid until 2005. At this date, in accordance with the committees decision, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. 4 60938-2-2 IEC:1999 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRES
30、SION Part 2-2: Blank detail specification Inductors for which safety tests are required (only) INTRODUCTION Blank detail specification This blank detail specification forms the basis for a uniform procedure for a common mark. It implements the approval schedule for safety tests only in IEC 60938-2,
31、requires a declaration of design for parameters relevant to safety tests and prescribes conformance tests to be conducted on every lot prior to its release and re-qualification tests depending on changes of the design. In comparison with IEC 60938-2-1 which provides safety tests and performance test
32、s, this specification is restricted to safety tests only. The use of IEC 60938-2-1 may be more appropriate for components manufactured in mass production, whereas this specification may be necessary in those cases where approval and re- qualification tests contribute considerably to the costs of the
33、 product. A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. In the preparation of detail specifications the content of 1.4 of the sectional specification shall be taken
34、into account. The numbers between square brackets on the first page of the detail specification correspond to the following information which shall be inserted in the position indicated. Identification of the detail specification and of the inductor The first page of the detail specification should
35、have the layout recommended on the next page of this blank detail specification. 0 Manufacturers name. 0A Manufacturers style designation. 1 The “International Electrotechnical Commission“ or the National Standards Organisation under whose authority the detail specification is drafted. 2 The IEC or
36、National Standards number of the detail specification, date of issue and any further information required by the national system. 3 The number and issue number of the IEC or national generic specification. 4 The IEC number of the blank detail specification. Identification of the inductor 5 A short d
37、escription of the inductor or range of inductors. 6 Information on typical construction (when applicable). 60938-2-2 IEC:1999 5 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternativel
38、y, this drawing may be given in an annex to the detail specification, but should always contain an illustration of the general outer appearance of the inductor. 8 Reference data on the most important properties, to allow comparison between the various inductor types intended for the same, or for sim
39、ilar applications. 1 IEC 60938-2-1XX 2 QC XXXXXXXXXXXX ELECTRONIC COMPONENTS OF ASSESSED IEC 60938-2-2 4 QUALITY IN ACCORDANCE WITH: QC XXXXXX 3 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION FOR WHICH SAFETY 5 Outline drawing: (see table 1) TESTS ARE REQUIRED (. angle projection) 7 6
40、(Other shapes are permitted within the dimensions given) Safety tests only 8 NOTES 1 to 9 see pages 3 and 4. Information on the availability of components qualified to this detail specification is given in the Register of Approvals. 1 General data 1.1 Recommended method(s) of mounting (to be inserte
41、d) (See 1.4.3 of IEC 60938-2.) 6 60938-2-2 IEC:1999 1.2 Dimensions Table 1 Dimensions related to case size Case size reference or type Dimensions mm L 1W H L 2L 3L 4NOTE 1 When there is no case size reference, the dimensions should be given per type designation. NOTE 2 The dimensions should be given
42、 as maximum dimensions or as nominal dimensions with a tolerance. 1.3 Ratings and characteristics Rated inductance (L R ) (see table 2) Tolerance on rated inductance Rated current (I) range (see table 2) DC resistance (R) (see table 2) Rated voltage Rated temperature Climatic category Category of pa
43、ssive flammability (if applicable) Table 2 Values of inductance, rated current and d.c. resistance related to type designation Ordering code, type designation L Rper line mH I RA R maxper line 1.4 Related documents Generic specification: IEC 60938-1:1999, Fixed inductors for electromagnetic interfer
44、ence suppression Part 1: Generic specification Sectional specification: IEC 60938-2:1999, Fixed inductors for electromagnetic interference suppression Part 2: Sectional specification 60938-2-2 IEC:1999 7 1.5 Marking The marking of the inductor shall be in accordance with the requirements of 1.6 of I
45、EC 60938-2. The details of the marking of the component and package shall be given in full in the detail specification. 1.6 Ordering information Orders for inductors covered by this specification shall contain, in clear or in coded form, the following minimum information: a) type designation; b) rat
46、ed inductance; c) tolerance on rated inductance; d) rated voltage; e) rated current; f) number and issue reference of the detail specification and style reference. 1.7 Additional information (not for inspection purposes) 1.8 Additional or increased severities or requirements to those specified in th
47、e generic or sectional specification NOTE Additions or increased requirements should be specified only when essential. Table 3 Other characteristics This table is to be used for defining characteristics which are additional to or more severe than those given in the sectional specification. 2 Inspect
48、ion requirements 2.1 Procedures For qualification approval, the procedures shall be in accordance with 3.4 of IEC 60938-2. 2.2 Test schedules 2.2.1 Initial approval See table 1 and annex A of the sectional specification. 2.2.2 Conformance tests See table 4 of this specification in association with a
49、nnex A of this specification. 2.2.2.1 Conformance tests (lot-by-lot) 8 60938-2-2 IEC:1999 Table 4 Conformance tests Subclause number and test (see note 1) D or ND (see note 3) Conditions of test (see note 1) Sample size Requirements (see note 1) 4.4 Inductance 4.1 Visual examination 4.2 Voltage proof ND 100 % (see note 2) Within specified tolerance Legible marki
