1、INTERNATIONAL STANDARD IEC 60115-9 First edition 2003-10 Fixed resistors for use in electronic equipment Part 9: Sectional specification: Fixed surface mount resistor networks with individually measurable resistors Reference number IEC 60115-9:2003(E)Publication numbering As from 1 January 1997 all
2、IEC publications are issued with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publi
3、cation, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. In
4、formation relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the technical committee which has p
5、repared this publication, as well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to search by a variety of criteria including text searches,
6、 technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications (www.iec.ch/online_news/ justpub) is also available by ema
7、il. Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: custserviec.ch Tel: +41 22 919 02 11 Fax: +41 22 919 03 00 I
8、NTERNATIONAL STANDARD IEC 60115-9 First edition 2003-10 Fixed resistors for use in electronic equipment Part 9: Sectional specification: Fixed surface mount resistor networks with individually measurable resistors IEC 2003 Copyright - all rights reserved No part of this publication may be reproduced
9、 or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone: +41 22 919 02 11 Telefax: +41
10、 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch P For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International Electrotechnical Commission 2 60115-9 IEC:2003(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT Part
11、 9: Sectional specification: Fixed surface mount resistor networks with individually measurable resistors FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The
12、 object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifi
13、cations (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations
14、liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters ex
15、press, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Comm
16、ittees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC Natio
17、nal Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no
18、marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, ser
19、vants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publicat
20、ion, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibilit
21、y that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60115-9 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipm
22、ent. The text of this standard is based on the following documents: FDIS Report on voting 40/1344/FDIS 40/1366/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with
23、the ISO/IEC Directives, Part 2.60115-9 IEC:2003(E) 3 The committee has decided that the contents of this publication will remain unchanged until 2008. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual edition of this standard may be
24、issued at a later date. 4 60115-9 IEC:2003(E) FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT Part 9: Sectional specification: Fixed surface mount resistor networks with individually measurable resistors 1 General 1.1 Scope This part of IEC 60115 is applicable to fixed surface mount resistor network
25、s with individually measurable resistors for use in electronic equipment. 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60115-1, the appropriate Quality Assessment procedures, tests and measuring methods and to give general perfor
26、mance requirements for this type of resistor. Test severities and requirements prescribed in detail specifications referring to this sectional specification must be of equal or higher performance level, because lower performance levels are not permitted. 1.3 Normative references The following refere
27、nced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60063:1963, Preferred number series for resistors and capacitors
28、Amendment 1 (1967) Amendment 2 (1977) IEC 60068-1: Environmental testing Part 1: General and guidance IEC 60068-2-1: Environmental testing Part 2: Tests. Tests A: Cold IEC 60068-2-2: Environmental testing Part 2: Tests. Tests B: Dry heat IEC 60115-1:1999, Fixed resistors for use in electronic equipm
29、ent Part 1: Generic specification 1.4 Information to be given in a detail specification Detail specifications shall be derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional specification or blank detail
30、specification. When more severe requirements are included, they shall be listed in 1.8 of the detail specification and indicated in the test schedules, for example by an asterisk.60115-9 IEC:2003(E) 5 The following information shall be given in each detail specification and the values quoted shall p
31、referably be selected from those given in the appropriate clause of this sectional specification. 1.4.1 Outline drawing and dimensions There shall be an illustration of the surface mount resistor network as an aid to easy recognition and for comparison of the surface mount resistor network with othe
32、rs. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given in the detail specification. All dimensions shall be stated in millimetres. Normally the numerical values shall be given for the length, width and thickness of the body. Schematic diagrams an
33、d pin identifications shall be given in the detail specification. Those are prescribed in Annex A. Configurations of terminations shall be given in the detail specification. Those are prescribed in Annex B. When the outline drawing is other than described above, the detail specification shall state
34、such dimensional information as will adequately describe the surface mount resistor network. 1.4.2 Mounting The detail specification shall give guidance on methods of mounting for normal use. Mounting for test and measurement purposes (when required) shall be in accordance with 4.31 of IEC 60115-1.
35、1.4.3 Style (2.2.2 of IEC 60115-1) The styles given in Table 1 are preferred. All dimensions are in mm. Table 1 Style and outline dimensions Dimensions in mm Code Length L Width W Thickness T Diagram a) Construction of terminalsa) 1005X2 1 0,1 1 0,1 0,35 0,1 AC o n v e x 1005X4 2 0,1 1 0,1 0,4 0,15
36、A Convex Concave 1608X2 1,6 0,2 1,6 0,2 0,55 0,15 A Convex Concave 1608X4 3,2 0,2 1,6 0,2 0,55 0,15 A Convex Concave 3216X4 5,08 0,2 3,1 0,2 0,55 0,15 A Convex Concave 3216 3,2 0,2 1,6 0,2 0,5 0,15 B, C Convex 4021 4 0,2 2,1 0,2 0,6 0,15 D Concave 6431 6,4 0,2 3,1 0,2 0,6 0,15 B, C Convex Concave a)
37、 Diagrams are shown in Annex A. Constructions of terminals are shown in Annex B. 6 60115-9 IEC:2003(E) 1.4.4 Ratings and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification together with the following: Rated resistance range See 2.2.
38、1. The preferred values are those of the E-series of IEC 60063. NOTE When products approved to the detail specification have different ranges, the following statement should be added: “The range of values available in each style is given in the qualified products list”. 1.4.5 Marking The detail spec
39、ification shall specify the content of the marking on the surface mount resistor network and on the package. Surface mount resistor networks are generally not marked on the body. If some marking can be applied, the surface mount resistor network shall be clearly marked with the rated resistance and
40、as many of the remaining items in 2.4 of IEC 60115-1 as possible. All items shall be marked on the package. Deviations from the above mentioned requirements shall be specifically stated. 2 Preferred ratings, characteristics and test severities 2.1 Preferred ratings and characteristics The values giv
41、en in detail specifications shall preferably be selected from the following: 2.1.1 Preferred climatic categories The surface mount resistor networks covered by this specification are classified into climatic categories according to the general rules given in IEC 60068-1. The lower and upper category
42、 temperature and the duration of the damp heat, steady state shall be chosen from the following: Lower category temperature: 55 C, 40 C, 25 C and 10 C. Upper category temperature: +85 C, +100 C, +125 C and +155 C. Duration of the damp heat, steady state test: 4, 10, 21 and 56 days. The severities fo
43、r the cold and dry heat tests are the lower and upper category temperatures respectively. Because of the construction of some surface mount resistor networks these temperatures will occur between two of the preferred temperatures given in IEC 60068-2-1 and IEC 60068-2-2. In this event, the nearest p
44、referred temperature within the actual temperature range of the surface mount resistor network shall be chosen for this severity. 2.1.2 Temperature coefficients and temperature characteristics of resistance The preferred limits of change in resistance for the temperature characteristics of resistanc
45、e test are given in Table 2.60115-9 IEC:2003(E) 7 Each line in the table gives the preferred temperature coefficient and corresponding temperature characteristic for 20 C to 70 C and limits of change in resistance for the measurement of the temperature characteristic of resistance (see 4.8 of IEC 60
46、115-1) on the basis of category temperature ranges of 2.1.1 of this sectional specification. Table 2 Temperature coefficients and temperature characteristics of resistance Temperature characteristic of resistance (limits of percentage change in resistance) Temper- ature coeffi- cient Temper- ature c
47、harac- teristic 20/70 C Reference temperature /lower category temperature Reference temperature /upper category temperature 10 6 /K % +20/55 +20/40 +20/25 +20/10 +20/+85 +20/+100 +20/+125 +20/+155 500 2,5 3,75 3 2,25 1,500 3,25 4 5,25 6,75 250 1,25 1,88 1,5 1,13 0,750 1,62 2 2,62 3,38 100 0,5 0,75 0
48、,6 0,45 0,300 0,65 0,8 1,05 1,35 50 0,25 0,375 0,3 0,23 0,150 0,325 0,4 0,525 0,675 25 0,125 0,188 0,15 0,113 0,075 0,162 0,2 0,262 0,338 15 0,075 0,113 0,09 0,068 0,045 0,098 0,12 0,158 0,203 10 0,05 0,075 0,06 0,045 0,030 0,065 0,08 0,105 0,135 NOTE 1 Resistors having an upper category temperature
49、 of +85 C need not be measured between 20 C and 70 C. NOTE 2 If measurements are required at additional temperatures, these shall be specified in the detail specification. 2.1.3 Limits for change in resistance For each stability class the preferred limits for change in resistance for each of the tests listed in the head
