1、 IEC/TR 62258-8 Edition 1.0 2008-05 TECHNICAL REPORT Semiconductor die products Part 8: EXPRESS model schema for data exchange IEC/TR 62258-8:2008(E) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publi
2、cation may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an
3、enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International E
4、lectrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure
5、 that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on project
6、s, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading onlin
7、e dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wis
8、h to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC/TR 62258-8 Edition 1.0 2008-05 TECHNICAL REPORT Semiconductor die products Part 8: EXPRESS model sc
9、hema for data exchange INTERNATIONAL ELECTROTECHNICAL COMMISSION U ICS 31.080.99 PRICE CODE ISBN 2-8318-9779-3 2 TR 62258-8 IEC:2008(E) CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope.6 2 Normative references6 3 Terms and definitions .7 4 General 7 5 Data exchange .7 Annex A (normative) EXPRESS model sch
10、ema 8 Annex B (informative) STEP physical file example25 TR 62258-8 IEC:2008(E) 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SEMICONDUCTOR DIE PRODUCTS Part 8: EXPRESS model schema for data exchange FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for stan
11、dardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes In
12、ternational Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may particip
13、ate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement betwe
14、en the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publication
15、s have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
16、 misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding
17、national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edi
18、tion of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether di
19、rect or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispen
20、sable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. The main task of IEC technical commi
21、ttees is to prepare International Standards. However, a technical committee may propose the publication of a technical report when it has collected data of a different kind from that which is normally published as an International Standard, for example “state of the art“. IEC 62258-8, which is a tec
22、hnical report, has been prepared by subcommittee 47: Semiconductor devices. The text of this technical report is based on the following documents: Enquiry draft Report on voting 47/1927/DTR 47/1952/RVC Full information on the voting for the approval of this technical report can be found in the repor
23、t on voting indicated in the above table. 4 TR 62258-8 IEC:2008(E) This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62258 series, under the general title Semiconductor die products, can be found on the IEC website. Further parts may
24、be added as required. The committee has decided that the contents of this publication will remain unchanged until the maintenance result dateindicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed,
25、 withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. TR 62258-8 IEC:2008(E) 5 INTRODUCTION This technical report is based on the work carried out in the ESPRIT 4 thFramework project GOODDIE which resulted in the publication of
26、the ES 59008 series of European specifications. Organisations that helped prepare this document included the ESPRIT ENCAST project, the Die Products Consortium, JEITA, JEDEC and ZVEI. 6 TR 62258-8 IEC:2008(E) SEMICONDUCTOR DIE PRODUCTS Part 8: EXPRESS model schema for data exchange 1 Scope This part
27、 of IEC 62258, which is a technical report, has been developed to facilitate the production, supply and use of semiconductor die products, including wafers, singulated bare die, die and wafers with attached connection structures, minimally or partially encapsulated die and wafers. This Technical Rep
28、ort contains an EXPRESS model schema that describes the elements needed for data exchange and that will allow the implementation of the requirements of the IEC 62258-1, IEC 62258-5 and IEC 62258-6 standards, as well as providing an exchange structure that is complementary to those defined in IEC 622
29、58-2. It is also complementary to and compatible with the questionnaire in IEC 62258-4. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition o
30、f the referenced document (including any amendments) applies. IEC 60050 (all parts), International Electrotechnical Vocabulary IEC 62258-1, Semiconductor die products Part 1: Requirements for procurement and use IEC 62258-2, Semiconductor die products Part 2: Exchange data formats IEC/TR 62258-4, Se
31、miconductor die products Part 4: Questionnaire for die users and suppliers IEC 62258-5, Semiconductor die products Part 5: Requirements for information concerning electrical simulation IEC 62258-6, Semiconductor die products Part 6: Requirements for information concerning thermal simulation ISO 1030
32、3-11:2004, Industrial automation systems and integration Product data representation and exchange Part 11: Description methods: The EXPRESS language reference manual ISO 10303-21:2002, Industrial automation systems and integration Product data representation and exchange Part 21: Implementation meth
33、ods: Clear text encoding of the exchange structure TR 62258-8 IEC:2008(E) 7 3 Terms and definitions For the purposes of this document, relevant terms, which are defined in IEC 60050 together with additional terms and acronyms as given in IEC 62258-1 apply. 4 General The EXPRESS model schema given in
34、 this Technical Report complies with ISO 10303-11 and allows for exchange of data on die devices using the STEP Physical File format (SPF) as defined in ISO 10303-21. To comply with IEC 62258-1, that standard requires that suppliers of die devices shall furnish information that is necessary and suff
35、icient for users of die devices at all stages of design, procurement, manufacture and test of products containing them. The EXPRESS model schema at Annex A defines an exchange mechanism for structuring such information using a representation that complies with the schema and as such is intended as a
36、n aid to compliance with the standard. Whilst it is expected that much of the information supplied will be in the public domain and available from such sources as manufacturers data sheets, neither the standard nor the schema places an obligation on a supplier to make information public. Any informa
37、tion that a supplier considers to be proprietary or commercially sensitive may be supplied under the terms of a non-disclosure agreement. 5 Data exchange The EXPRESS model schema at Annex A implements all the entities as defined by IEC 62258-2 for the DDX format. In addition, it includes additional
38、entities extending the range of that data as follows: Expansion of data on organisations (manufacturer, supplier etc.) to include addresses and contacts Sub-division of some entities to make their values clearer. Annex B contains an example of a STEP Physical File based on the model schema using a f
39、ictitious example similar to that employed in IEC 62258-2, extended to cover additional data requirements. It is possible that software may be available for conversion of data produced using the spreadsheet associated with IEC 62258-4 into this format. In any case, a wide range of tools is available
40、 commercially for handling and processing STEP files. The electronic form of the schema contained in this Technical Report may be downloaded from the IEC website. The copyright conditions applying to the use of the electronic file are those that apply to IEC database standards, which permit the use
41、of such information in electronic form for bona-fide e-commerce but do not permit its sale to third parties or other commercial use. 8 TR 62258-8 IEC:2008(E) Annex A (normative) EXPRESS model schema A.1 General This Annex contains the full EXPRESS listing of the schema, annotated with comments and e
42、xplanatory text. The order of text in this clause is determined primarily by the order imposed by the EXPRESS language, secondarily by importance. *) SCHEMA ddx_schema_version_2_0; (* A.2 Type definitions This clause contains definitions for the types used within this EXPRESS model. *) TYPE date_typ
43、e = STRING(10) FIXED; END_TYPE; TYPE text_type = STRING(255); END_TYPE; TYPE geometric_unit_type = ENUMERATION OF (micron, metre, millimetre, inch, mil); END_TYPE; TYPE geometric_view_value = ENUMERATION OF (top,bottom); END_TYPE; (* * A distance in the corresponding “geometric_unit“. *) TYPE geomet
44、ric_value = REAL; END_TYPE; TYPE integer_value = INTEGER; WHERE non_negative: SELF = 0; END_TYPE; (* Formal propositions: non_negative: The integer is non-negative *) TYPE angle_value = INTEGER; WHERE valid_value: 0 = SELF = 359; END_TYPE; (* Formal propositions: valid_value: The angle can take valu
45、es from 0 to 359 degrees TR 62258-8 IEC:2008(E) 9 *) TYPE celsius_value = REAL; END_TYPE; TYPE time_value = REAL; END_TYPE; TYPE watt_value = REAL; END_TYPE; TYPE device_name_type = TEXT_TYPE; END_TYPE; TYPE standards_compliance_type = text_type; END_TYPE; TYPE additional_screening_type = text_type;
46、 END_TYPE; TYPE reliability_calculation_type = text_type; END_TYPE; TYPE product_status_type = text_type; END_TYPE; TYPE testability_features_type = text_type; END_TYPE; TYPE additional_test_type = text_type; END_TYPE; TYPE form_of_supply_type = text_type; END_TYPE; TYPE packing_code_type = text_typ
47、e; END_TYPE; TYPE wafer_die_step_size_type = size_value; END_TYPE; TYPE wafer_gross_die_count_type = integer_value; END_TYPE; TYPE wafer_index_type = ENUMERATION OF (flat, notch); END_TYPE; TYPE wafer_index_orientation_type = angle_value; END_TYPE; TYPE wafer_reticule_step_size_type = size_value; 10
48、 TR 62258-8 IEC:2008(E) END_TYPE; TYPE wafer_reticule_gross_die_count_type = integer_value; END_TYPE; TYPE ic_technology_type = text_type; END_TYPE; TYPE data_source_type = text_type; END_TYPE; TYPE data_version_type = text_type; END_TYPE; TYPE block_version_type = text_type; END_TYPE; TYPE function
49、_type = text_type; END_TYPE; TYPE manufacturer_type = text_type; END_TYPE; TYPE pad_metallisation_type = text_type; END_TYPE; TYPE die_passivation_material_type = text_type; END_TYPE; TYPE terminal_material_type = text_type; END_TYPE; TYPE terminal_structure_type = text_type; END_TYPE; TYPE type_number_type = text_type; END_TYPE; TYPE die_name_type = text_type; END_TYPE; TYPE die_semiconductor_material_type = text_type; END_TYPE; TYPE die_back_detail_type = text_t
