1、 IEC 61326-2-2 Edition 2.0 2012-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Electrical equipment for measurement, control and laboratory use EMC requirements Part 2-2: Particular requirements Test configurations, operational conditions and performance criteria for portable test, measuring and mon
2、itoring equipment used in low-voltage distribution systems Matriel lectrique de mesure, de commande et de laboratoire Exigences relatives la CEM Partie 2-2: Exigences particulires Configurations dessai, conditions de fonctionnement et critres de performance des matriels portatifs dessai, de mesure e
3、t de surveillance utiliss dans des systmes de distribution basse tension IEC61326-2-2:2012 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any
4、means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publicati
5、on, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou m
6、canique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou con
7、tactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that
8、 prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might ha
9、ve been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Publi
10、shed - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms contai
11、ning more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need
12、further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies
13、 apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La reche
14、rche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvel
15、les publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfi
16、nitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des qu
17、estions contactez-nous: csciec.ch. IEC 61326-2-2 Edition 2.0 2012-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Electrical equipment for measurement, control and laboratory use EMC requirements Part 2-2: Particular requirements Test configurations, operational conditions and performance criteria fo
18、r portable test, measuring and monitoring equipment used in low-voltage distribution systems Matriel lectrique de mesure, de commande et de laboratoire Exigences relatives la CEM Partie 2-2: Exigences particulires Configurations dessai, conditions de fonctionnement et critres de performance des matr
19、iels portatifs dessai, de mesure et de surveillance utiliss dans des systmes de distribution basse tension INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE J ICS 17.220; 25.040.40; 33.100 PRICE CODE CODE PRIX ISBN 978-2-83220-397-2 Registered trademark of the Inte
20、rnational Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61326-2-2 IEC:2
21、012 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 5 4 General 6 5 EMC test plan . 6 5.1 General . 6 5.2 Configuration of EUT during testing . 6 5.3 Operation conditions of EUT during testing 8 5.4 Specification of functional performance . 8 5.5 Test descripti
22、on . 8 6 Immunity requirements . 8 6.1 Conditions during the tests 8 6.2 Immunity test requirements . 8 6.3 Random aspects 9 6.4 Performance criteria 9 7 Emission requirements . 9 8 Test results and test report . 9 9 Instructions for use . 9 Figure 101 Test set-up for portable test, measuring and mo
23、nitoring equipment based on IEC 61000-4-3 . 7 Figure 102 Example of connection details for voltage measurements . 7 Figure 103 Example of connection details for current measurements . 8 61326-2-2 IEC:2012 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND
24、 LABORATORY USE EMC REQUIREMENTS Part 2-2: Particular requirements Test configurations, operational conditions and performance criteria for portable test, measuring and monitoring equipment used in low-voltage distribution systems FOREWORD 1) The International Electrotechnical Commission (IEC) is a
25、worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to oth
26、er activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the
27、subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions
28、 determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National
29、Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in
30、which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publ
31、ication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is
32、 not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its tec
33、hnical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IE
34、C Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subj
35、ect of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61326-2-2 has been prepared by subcommittee 65A: System aspects, of IEC technical committee 65: Industrial-process measurement, control and automation. This second editio
36、n cancels and replaces the first edition published in 2005. This edition constitutes a technical revision. The main technical changes with regard to the previous edition are as follows: Update with respect to IEC 61326-1:2012. 4 61326-2-2 IEC:2012 The text of this standard is based on the following
37、documents: FDIS Report on voting 65A/642/FDIS 65A/653/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part of IEC 61326 se
38、ries is to be used in conjunction with IEC 61326-1:2012 and follows the same numbering of clauses, subclauses, tables and figures. When a particular subclause of IEC 61326-1 is not mentioned in this part, that subclause applies as far as is reasonable. When this standard states “addition”, “modifica
39、tion” or “replacement”, the relevant text in IEC 61326-1 is to be adapted accordingly. NOTE The following numbering system is used: subclauses, tables and figures that are numbered starting from 101 are additional to those in IEC 61326-1; unless notes are in a new subclause or involve notes in IEC 6
40、1326-1, they are numbered starting from 101 including those in a replaced clause or subclause; additional annexes are lettered AA, BB, etc. A list of all parts of IEC 61326 series, under the general title Electrical equipment for measurement, control and laboratory use EMC requirements can be found
41、on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn
42、, replaced by a revised edition, or amended. 61326-2-2 IEC:2012 5 ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE EMC REQUIREMENTS Part 2-2: Particular requirements Test configurations, operational conditions and performance criteria for portable test, measuring and monitoring equip
43、ment used in low-voltage distribution systems 1 Scope In addition to the scope of IEC 61326-1, this part of IEC 61326 specifies more detailed test configurations, operational conditions and performance criteria for equipment covered by Annex A of IEC 61326-1 which is: used for testing, measuring or
44、monitoring of protective measures in low-voltage distribution systems, and; powered by battery and/or from the circuit measured, and portable. Examples of such EUT include, but are not limited to, voltage detectors, insulation testers, earth continuity testers, earth resistance testers, loop impedan
45、ce testers, “residual-current-device-testers” (RCD-testers) and phase sequence testers as defined in IEC 61557. NOTE Particular EMC requirements for equipment covered by IEC 61557-8 and IEC 61557-9 are given in IEC 61326-2-4. The manufacturer specifies the environment for which the product is intend
46、ed to be used and/or select the appropriate test level specifications of IEC 61326-1. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For
47、undated references, the latest edition of the referenced document (including any amendments) applies. Clause 2 of IEC 61326-1:2012 applies, except as follows: Addition: IEC 61326-1:2012, Electrical equipment for measurement, control and laboratory use EMC requirements Part 1: General requirements IE
48、C 61557 (all parts), Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 61326-1 and IEC 60050
49、-161 apply. 6 61326-2-2 IEC:2012 4 General Clause 4 of IEC 61326-1 applies. 5 EMC test plan 5.1 General Subclause 5.1 of IEC 61326-1 applies. 5.2 Configuration of EUT during testing Subclause 5.2 of IEC 61326-1 applies, except as follows: Addition: 5.2.4.101 Test and measurement I/O ports Electrostatic discharge shall be applied to the housing, to the terminals of the EUT and to the cou
