1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 60745-2-11Hand-Held Motor-Operated Electric Tools - Safety - Part 2-11: Particular Requirements forReciprocating SawsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER
2、REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 60745-2-11Hand-Held Motor-Operated Electric Tools - Safety - Part 2-11: Particular Requirements forReciprocating SawsEdition: 2Edition Date: March 26, 2004The revisions dated May 15, 2014 are being issued to reaffirm ap
3、proval of UL 60745-2-11 as anAmerican National Standard. No changes in requirements are involved.As noted in the Commitment for Amendments statement located on the back side of the titlepage, UL and CSA are committed to updating this harmonized standard jointly. However, therevision pages dated May
4、15, 2014 will not be jointly issued by UL and CSA as these revisionpages address UL ANSI approval dates only.This document provides a single listing of the National Differences included in the UL adoption ofthe corresponding IEC standard.All rights reserved. No part of this publication may be reprod
5、uced, stored in a retrieval system, ortransmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwisewithout prior permission of UL.UL provides this standards document as is without warranty of any kind, either expressed or implied,including but not limited to, the
6、 implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special, incidental, consequential, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this st
7、andards document, even if UL or an authorized UL representative has been advisedof the possibility of such damage. In no event shall ULs liability for any damage ever exceed the pricepaid for this standards document, regardless of the form of the claim.Users of the electronic versions of ULs Standar
8、ds for Safety agree to defend, indemnify, and hold ULharmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonableattorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronicStandard on the purchasers computer sy
9、stem.Copyright Underwriters Laboratories Inc.MAY 15, 2014NATIONAL DIFFERENCES FOR UL UL 60745-2-112UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPrefaceThis document provides a single listing of the technical National Differences included in
10、 the UL adoptionof the corresponding IEC standard.In its IEC-based standards, UL uses the notations indicated below to identify national difference type, andthese types are additionally noted in this document. The standard may not use all types of thesedeviations.D1 - These are deviations which are
11、based on basic safety principles and requirements, elimination ofwhich would compromise safety for U.S. consumers and users of products.D2 - These are deviations based on safety practices. These are deviations for IEC requirements that maybe acceptable, but adopting the IEC requirements would requir
12、e considerable retesting or redesign on themanufacturers part.DC - These are deviations based on the component standards and will not be deleted until a particularcomponent standard is harmonized with the IEC component standard.DE - These are deviations based on editorial comments or corrections.DR
13、- These are deviations based on the national regulatory requirements.Each national difference contains a description of what the national difference entails. Typically one of thefollowing words is used to explain how the text of the national difference is to be applied to the base IECtext:Addition /
14、 Add - An addition entails adding a complete new numbered clause, subclause, table,figure, or annex. Addition is not meant to include adding select words to the base IEC text.Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause,table, figure, or annex with
15、out any replacement text.Modification / Modify - A modification is an altering of the existing base IEC text such as theaddition, replacement or deletion of certain words or the replacement of an entire clause,subclause, table, figure, or annex of the base IEC text.MAY 15, 2014 NATIONAL DIFFERENCES
16、FOR UL UL 60745-2-11 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences8.12.1DV D1 Modification: Add the following: Use clamps or another practical way to secure and support the workpiece to astable platform. Holding the work by hand or against your body leaves it unstable andmay lead to loss of control.Annex 11.DVL DE Addition: Add the following Annex:Reference National Difference Type8.12.1DV D1 ModificationAnnex 11.DVL DE AdditionMAY 15, 2014NATIONAL DIFFERENCES FOR UL UL 60745-2-114