1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUNDERWRITERS LABORATORIES INC. CERTIFICATION REQUIREMENT DECISIONThis Certification Requirement Decision is prepared and published by Underwriters Laboratories Inc.(UL). It is normative for the a
2、pplicable UL Product Certification Program(s); however, it is currently notpart of the UL Standard(s) referenced below.Product Category (CCN): QLHN, QLIWStandard Number: UL 1682Standard Title: Standard for Plugs, Receptacles, and Cable Connectors of the Pinand Sleeve TypeEdition Date: October 4, 201
3、3Edition Number: 4Section / Paragraph Reference: (New) Supplement SASubject: Replacement Parts FOR USE WITH SPECIFIC MANUFACTURERS PLUGS,RECEPTACLES, and CABLE CONNECTORS of the PIN and SLEEVE TYPEDECISION:Addition of new requirements to UL 1682 the Standard for Plugs, Receptacles, and Cable Connect
4、ors ofthe Pin and Sleeve Type, an identified replacement part shall also comply with the following SupplementSA.SUPPLEMENT SA - REPLACEMENT PARTS FOR USE WITH SPECIFIC MANUFACTURERS PLUGS,RECEPTACLES, and CABLE CONNECTORS of the PIN and SLEEVE TYPEINTRODUCTION1 Scope1.1 These requirements cover repl
5、acement parts (see 3.1) intended for use in the specific manufacturersplugs, receptacles and cable connectors of the pin and sleeve type.2 General2.1 In addition to complying with Sections3-8ofthese requirements, the replacement parts alone, andin combination with the complete device (plugs, recepta
6、cles and cable connectors, respectively), shallcomply with the applicable Construction and Performance requirements of the Standard for Plugs,Receptacles and Cable Connectors of the Pin and Sleeve Type, UL 1682.3 Glossary3.1 REPLACEMENT PART An individual replacement part identified by the manufactu
7、rer, for use in thesame manufacturers complete device.Note: The replacement part is packaged as a “kit” containing the individual part and installation instructions (See Section 8 of thisSupplement).CONSTRUCTION4 GeneralUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION W
8、ITHOUT PERMISSION FROM UL4.1 The replacement part shall be formed and assembled so that it may be installed, in accordance withthe installation instructions, into its specified attachment plug, cord connector, receptacle of the pin andsleeve type, without risk of fire or electric shock. Risk of fire
9、 or electric shock is determined by compliancewith the construction and performance requirements herein and the applicable requirements of theStandard for Plugs, Receptacles and Cable Connectors of the Pin and Sleeve type, UL 1682.4.2 A replacement part shall only be installed using commonly used to
10、ols such as a screw driver or awrench. A replacement part shall not be permitted that requires the installer to remove or defeat or replacea factory installed securement means such as a rivet or drive pin.PERFORMANCE5 General5.1 If the replacement part is recommended for use with more than one devic
11、e, each representativecombination of replacement part and device shall be investigated.6 Replacement Part Assembly Test6.1 The replacement part shall be able to be installed to the specified device and shall be reliably retainedin place without causing an increased risk of fire or electric shock. Co
12、mpliance is determined by inspectionand the test of 6.2 shall be performed.6.2 A sample of the replacement part shall be assembled to its specified device using the manufacturersinstallation instructions. Upon completion of the assembly, the integrity of the completed assembly shallbe examined and i
13、f necessary, subjected to the applicable performance testing necessary to maintaincontinued compliance with this Standard.MARKINGS7 General7.1 The replacement part shall be provided in the form of a kit, including marking as detailed in Section7 of this outline.7.2 A required marking shall be molded
14、, die-stamped, paint-stenciled, stamped or etched metal that ispermanently secured, or indelibly stamped lettering on a pressure-sensitive label secured by adhesivethat, upon investigation, meets the intent of the requirement for the application.7.3 The replacement part shall be provided with the fo
15、llowing identification markings:a) Manufacturers name, and;b) Specific catalog or series number, and;c) The date or other dating period of manufacture not exceeding any three consecutive months.Exception: Abbreviation of the date of manufacture, or provision in a nationally acceptedconventional code
16、 or in a code affirmed by the manufacturer, meets the intent of the requirement.7.4 The replacement part packaging shall be marked with the following marking or equivalent:STANDARD NUMBER: UL 1682 -2-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FR
17、OM ULWARNING - Use only replacement part (Catalog Number) with (+) Pin & Sleeve Attachment Plug, CordConnector, Receptacle (as appropriate) Only.Where “(+)” is to be substituted with the specific manufacturer name and model / catalog number of theintended device(s).INSTRUCTIONS8 General8.1 The repla
18、cement part shall be provided with instructions pertaining to its installation, operation, andmaintenance, as applicable.8.2 An illustration may be used to clarify the intent of a required instruction but shall not replace the writteninstruction.8.3 Instructions shall include the following statement
19、s or their equivalent:IMPORTANT SAFETY INSTRUCTIONSWARNING - Use only replacement part (Catalog Number) with (+) Pin & Sleeve Attachment Plug, CordConnector, Receptacle (as appropriate) Only, where (+) is to be substituted with the specificmanufacturer name and model / catalog number of the intended
20、 device(s).WARNING - Risk of Fire or Electric Shock. Do not use this replacement part with any pin & sleeveattachment plug, cord connector, receptacle (as appropriate), other than the one specified on thereplacement mark packaging and in these instructions.”SAVE THESE INSTRUCTIONS8.4 The opening and
21、 closing statements of the instructions specified in 8.3 - IMPORTANT SAFETYINSTRUCTIONS, and SAVE THESE INSTRUCTIONS, or the equivalent shall be entirely in upper caseletters or shall be emphasized to distinguish them from the rest of the text.RATIONALE FOR DECISION:It was brought to ULs attention t
22、hat pin and sleeve devices are routinely repaired in the field.Manufacturers provide replacement parts in the form of a “kit” to serve this purpose. To address this needto ensure continued compliance with the Standard, UL has developed requirements contained in a newUL 1682 Supplement SA, “Replaceme
23、nt parts for use with specific manufacturers plugs, receptacles, andcable connectors of the pin and sleeve type.”Copyright 2014 Underwriters Laboratories Inc.UL, in performing its functions in accordance with its objectives, does not guarantee or warrant thecorrectness of Certification Requirement D
24、ecisions it may issue or that they will be recognized or adoptedby anyone. Certification Requirement Decisions are the opinion of Underwriters Laboratories Inc. inpractically applying the requirements of the standard. They do not represent formal interpretations of thestandard under American Nationa
25、l Standards Institute (ANSI) processes. UL shall not be responsible toanyone for the use of or reliance upon Certification Requirement Decisions by anyone. UL shall not incurSTANDARD NUMBER: UL 1682 -3-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION
26、FROM ULany obligation or liability for damages, including consequential damages, arising out of or in connectionwith the use or reliance upon Certification Requirement Decisions. The electronic version of theCertification Requirement Decision is the current version and previously printed copies may be outdated.This document is published as a service to ULs certification customersSTANDARD NUMBER: UL 1682 -4-
