1、 TIA STANDARD Recommended Minimum Performance Standards for cdma2000High Rate Packet Data Access Network Equipment TIA-864-A (Revision of TIA-864)January 2006 TELECOMMUNICATIONS INDUSTRY ASSOCIATION The Telecommunications Industry Association represents the communications sector of Copyright Telecom
2、munications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufact
3、urers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or
4、non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted b
5、y TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all sa
6、fety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 3-4913
7、-RV1-1, formulated under the cognizance of the TIA TR-45.5 Subcommittee on Spread Spectrum Digital Technology). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELE
8、COMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) or search online at http:/www.tiaonline.org/standards/search_n_order.cfm All rights reserved Printed in U.S.A. Copyright Telec
9、ommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (including posting
10、 on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.tiaonline.org/abo
11、ut/faqDetail.cfm?id=18 OR Telecommunications Industry Association Standards (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or an
12、y editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and publishe
13、d pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IP
14、R. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or pr
15、actices suggested or provided in the Manual have been complied with as respects the Document or its contents. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of comp
16、liance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF
17、ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CO
18、NTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRE
19、CT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMA
20、GES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or netwo
21、rking permitted without license from IHS-,-,-TIA-864-A i NOTES xii 1 NORMATIVE REFERENCES . xiii 2 1 INTRODUCTION1-1 3 1.1 Scope 1-1 4 1.2 Terms and Definitions .1-1 5 1.2.1 Definitions.1-1 6 1.2.2 Terms 1-8 7 1.3 HRPD Equations .1-10 8 1.3.1 Transmit Power at the Access Terminal .1-10 9 1.3.2 Recei
22、ved Signal Strength .1-12 10 1.3.2.1 Connection Setup State .1-12 11 1.3.2.1.1 Access Probe Preamble Portion.1-12 12 1.3.2.1.2 Access Probe Capsule Portion 1-12 13 1.3.2.1.2.1 Single-Path Case 1-12 14 1.3.2.1.2.2 Two-Path Case .1-12 15 1.3.2.1.2.3 Three-Path Case.1-12 16 1.3.2.2 Connected State.1-13
23、 17 1.3.2.2.1 DRC Non-Gated Transmission .1-13 18 1.3.2.2.1.1 Single-Path Case 1-13 19 1.3.2.2.1.2 Two-Path Case .1-13 20 1.3.2.2.1.3 Three-Path Case.1-14 21 1.3.2.2.2 DRC Gated Transmission.1-15 22 1.3.2.2.2.1 Single-Path Case 1-15 23 1.3.2.2.2.2 Two-Path Case .1-15 24 1.3.2.2.2.3 Three-Path Case.1
24、-15 25 2 STANDARD EMISSIONS MEASUREMENT PROCEDURES .2-1 26 2.1 Radiated Emissions Measurement.2-1 27 2.1.1 Standard Radiation Test Site .2-1 28 2.1.2 Search Antenna.2-1 29 2.1.3 Field-Strength Measurement .2-2 30 2.1.4 Frequency Range of Measurements .2-2 31 2.1.5 Test Ranges .2-2 32 Copyright Telec
25、ommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-864-A ii 2.1.5.1 30-Meter Test Range2-2 1 2.1.5.2 3-Meter Test Range2-3 2 2.1.6 Radiated Signal Measurement Procedures.2-3 3 2.2 AC Power Li
26、ne Conducted Emissions Measurement 2-4 4 2.2.1 Standard AC Power Line Conducted Emissions Test Site.2-4 5 2.2.2 Line Impedance Stabilization Network (LISN) Unit.2-4 6 2.2.3 Standard Test Site Measurements.2-5 7 2.2.3.1 Floor Standing Equipment.2-5 8 2.2.3.2 Table Top Mounted Equipment2-5 9 2.2.3.3 M
27、easurement Procedure2-5 10 2.2.3.4 Frequency Range of Measurements .2-5 11 2.2.4 End User or Manufacturing Plant Test Sites2-5 12 3 Receiver Minimum Standards .3-1 13 3.1 Frequency Requirements.3-1 14 3.2 Access Probe Acquisition.3-1 15 3.2.1 Definition 3-1 16 3.2.2 Method of Measurement3-1 17 3.2.3
28、 Minimum Standard .3-3 18 3.3 Reverse Traffic Channel Demodulation3-3 19 3.3.1 Data Channel Demodulation Performance.3-4 20 3.3.1.1 Definition 3-4 21 3.3.1.2 Method of Measurement 3-4 22 3.3.1.3 Minimum Standard .3-7 23 3.3.2 DRC Channel Demodulation Performance .3-8 24 3.3.2.1 Definition 3-8 25 3.3
29、.2.2 Method of Measurement 3-9 26 3.3.2.3 Minimum Standard .3-10 27 3.3.3 ACK Channel Demodulation Performance .3-11 28 3.3.3.1 Definition 3-11 29 3.3.3.2 Method of Measurement 3-11 30 3.3.3.3 Minimum Standard .3-12 31 3.3.4 DSC Channel Demodulation Performance .3-13 32 Copyright Telecommunications
30、Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-864-A iii 3.3.4.1 Definition.3-13 1 3.3.4.2 Method of Measurement 3-14 2 3.3.4.3 Minimum Standard3-15 3 3.4 Receiver Performance 3-15 4 3.4.1 Receiver Sen
31、sitivity3-15 5 3.4.1.1 Definition.3-15 6 3.4.1.2 Method of Measurement 3-15 7 3.4.1.3 Minimum Standard3-16 8 3.4.2 Receiver Dynamic Range3-16 9 3.4.2.1 Definition.3-16 10 3.4.2.2 Method of Measurement 3-16 11 3.4.2.3 Minimum Standard3-16 12 3.4.3 Single Tone Desensitization .3-17 13 3.4.3.1 Definiti
32、on.3-17 14 3.4.3.2 Method of Measurement 3-17 15 3.4.3.3 Minimum Standard3-19 16 3.4.4 Intermodulation Spurious Response Attenuation.3-19 17 3.4.4.1 Definition.3-19 18 3.4.4.2 Method of Measurement 3-19 19 3.4.4.3 Minimum Standard3-20 20 3.4.5 Adjacent Channel Selectivity3-20 21 3.4.5.1 Definition.3
33、-20 22 3.4.5.2 Method of Measurement 3-20 23 3.4.5.3 Minimum Standard3-21 24 3.4.6 Receiver Blocking Characteristics 3-21 25 3.4.6.1 Definition.3-21 26 3.4.6.2 Method of Measurement 3-21 27 3.4.6.3 Minimum Standard3-22 28 3.5 Limitations on Emissions 3-22 29 3.5.1 Conducted Spurious Emissions.3-22 3
34、0 3.5.1.1 Definition.3-22 31 3.5.1.2 Method of Measurement 3-22 32 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-864-A iv 3.5.1.3 Minimum Standard .3-23 1 3.5.2 Radiated S
35、purious Emissions3-23 2 3.6 Received Signal Quality Indicator (RSQI) .3-24 3 3.6.1 Definition 3-24 4 3.6.2 Method of Measurement3-24 5 3.6.3 Minimum Standard .3-25 6 4 Transmitter Minimum Standards4-1 7 4.1 Frequency Requirements.4-1 8 4.1.1 Frequency Coverage 4-1 9 4.1.2 Frequency Tolerance .4-1 10
36、 4.1.2.1 Definition 4-1 11 4.1.2.2 Method of Measurement 4-1 12 4.1.2.3 Minimum Standard .4-1 13 4.2 Modulation Requirements .4-1 14 4.2.1 Synchronization and Timing4-1 15 4.2.1.1 Pilot Channel Time Tolerance 4-1 16 4.2.1.1.1 Definition.4-2 17 4.2.1.1.2 Method of Measurement 4-2 18 4.2.1.1.3 Minimum
37、 Standard .4-2 19 4.2.2 Waveform Quality4-2 20 4.2.2.1 Definition 4-2 21 4.2.2.2 Method of Measurement 4-2 22 4.2.2.3 Minimum Standard .4-3 23 4.2.3 MAC Channel4-4 24 4.2.3.1 RPC Channel time Response4-4 25 4.2.3.1.1 Definition.4-4 26 4.2.3.1.2 Method of Measurement 4-4 27 4.2.3.1.3 Minimum Standard
38、 .4-6 28 4.2.4 Forward Traffic Channel4-7 29 4.2.4.1 Forward Traffic Channel Response to ACK Channel.4-7 30 4.2.4.1.1 Definition.4-7 31 4.2.4.1.2 Method of Measurement 4-7 32 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or netw
39、orking permitted without license from IHS-,-,-TIA-864-A v 4.2.4.1.3 Minimum Standard4-7 1 4.3 RF Output Power Requirements 4-8 2 4.3.1 Total Power4-8 3 4.3.1.1 Definition.4-8 4 4.3.1.2 Method of Measurement 4-8 5 4.3.1.3 Minimum Standard4-8 6 4.3.2 Pilot/MAC Channel Power .4-9 7 4.3.2.1 Definition.4
40、-9 8 4.3.2.2 Method of Measurement 4-9 9 4.3.2.3 Minimum Standard4-10 10 4.3.3 Code Domain Power.4-10 11 4.3.3.1 Code Domain Power of MAC Channel.4-11 12 4.3.3.1.1 Definition.4-11 13 4.3.3.1.2 Method of Measurement.4-11 14 4.3.3.1.3 Minimum Standard4-11 15 4.3.3.2 Code Domain Power of Forward Traffi
41、c and Control Channels4-12 16 4.3.3.2.1 Definition.4-12 17 4.3.3.2.2 Method of Measurement.4-12 18 4.3.3.2.3 Minimum Standard4-12 19 4.4 Limitations on Emissions 4-12 20 4.4.1 Conducted Spurious Emissions.4-12 21 4.4.1.1 Definition.4-12 22 4.4.1.2 Method of Measurement 4-12 23 4.4.1.3 Minimum Standa
42、rd4-13 24 4.4.2 Radiated Spurious Emissions 4-20 25 4.4.3 Inter-Sector Transmitter Intermodulation 4-20 26 4.4.3.1 Definition.4-20 27 4.4.3.2 Method of Measurement 4-21 28 4.4.3.3 Minimum Standard4-22 29 4.4.4 Occupied Bandwidth .4-22 30 4.4.4.1 Definition.4-22 31 4.4.4.2 Method of Measurement 4-22
43、32 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-864-A vi 4.4.4.3 Minimum Standard .4-22 1 5 General Requirements 5-1 2 5.1 Temperature and Power Supply Voltage 5-1 3 5.1.
44、1 Definition 5-1 4 5.1.2 Method of Measurement5-1 5 5.1.3 Minimum Standard .5-2 6 5.2 High Humidity 5-2 7 5.2.1 Definition 5-2 8 5.2.2 Method of Measurement5-2 9 5.2.3 Minimum Standard .5-2 10 5.3 AC Power Line Conducted Emissions 5-2 11 5.3.1 Definition 5-2 12 5.3.2 Method of Measurement5-3 13 5.3.
45、3 Minimum Standard .5-3 14 6 Standard Test Conditions .6-1 15 6.1 Standard Equipment.6-1 16 6.1.1 Basic Equipment.6-1 17 6.1.2 Associated Equipment.6-1 18 6.2 Standard Environmental Test Conditions6-1 19 6.3 Standard Conditions for the Primary Power Supply.6-1 20 6.3.1 General .6-1 21 6.3.2 Standard
46、 DC Test Voltage from Accumulator Batteries6-1 22 6.3.3 Standard AC Voltage and Frequency .6-2 23 6.4 Standard Test Equipment .6-2 24 6.4.1 Channel Simulator 6-2 25 6.4.2 Waveform Quality Measurement Equipment6-5 26 6.4.2.1 Rho Meter6-5 27 6.4.2.2 Code Domain Measurement Equipment.6-9 28 6.4.3 Acces
47、s Terminal Simulator6-13 29 6.4.4 AWGN Generator.6-14 30 6.4.5 CW Generator .6-14 31 6.4.6 Spectrum Analyzer 6-15 32 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-864-A vi
48、i 6.4.7 Average Power Meter6-16 1 6.4.8 RF Output Load.6-16 2 6.5 Functional System Setups.6-16 3 6.5.1 Functional Block Diagrams6-16 4 6.5.2 General Comments6-22 5 6.6 Standard Duty Cycle .6-23 6 6.7 Error Rates Measurement6-23 7 6.7.1 Packet Error Rates Measurement.6-23 8 6.7.2 DRC Channel Perform
49、ance Metrics6-23 9 6.7.3 ACK Channel Performance Metrics 6-23 10 6.7.4 DSC Channel Performance Metrics 6-24 11 6.8 Confidence Limits6-24 12 ANNEX A SELECTED PERFORMANCE REQUIREMENTS TABLES. A-1 13 A.1 Demodulation Requirements A-1 14 A.1.1 Access Probe Acquisition A-1 15 A.1.1.1 Method of Measurement . A-1 16 A.1.1.2 Minimum Sta
