欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SMPTE ST 233-2003 Motion-Picture Film (16-mm) - Projector Image Area and Projector Usage.pdf

    • 资源ID:1046812       资源大小:35.52KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SMPTE ST 233-2003 Motion-Picture Film (16-mm) - Projector Image Area and Projector Usage.pdf

    1、 1 Scope 1.1 This standard specifies the maximum dimensions of the film image area intended for projection from a 16-mm motion-picture film perforated one or two edges as specified in ANSI/SMPTE 109, and the placement of this area relative to the perforations and the reference edge of the film. 1.2

    2、This standard also specifies the position of the emulsion and the rate of projection for 16-mm motion-picture film perforated one or two edges, and the projector thread-up distance between audio and picture for 16-mm motion-picture film with audio. 2 Normative references The following standards cont

    3、ain provisions which, through reference in this text, constitute provisions of this standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this standard are encouraged to investigate the possibility of applyi

    4、ng the most recent edition of the standards indicated below. SMPTE 41-1999, Motion-Picture Film (16-mm) Prints Photographic Audio Records SMPTE 112-1999, Motion-Picture Film (16-mm) 100-Mil Magnetic Audio Record 3 Dimensions 3.1 The dimensions shall be as given in figure 1 and table 1. 3.2 The angle

    5、 between the horizontal edges of the image area and the reference edge of the film shall be 90 1/2. 4 Relationship to other standards 4.1 This standard may be used as the basis for establishing picture areas from original photography for final viewing because it presents a description of the picture

    6、 area on the projection print that is usable for the indicated purposes of the print (which is of primary importance because the projection print is the most commonly interchanged item). (See annex A.2.) 4.2 The following documents define image areas for other important phases of motion-picture oper

    7、ations, and are consistent with one another under currently acceptable commercial practice: SMPTE 7, ANSI/SMPTE 48, SMPTE 96, SMPTE RP 27.3, SMPTE RP 65. Page 1 of 4 pages SMPTE 233-2003 Revision of ANSI/SMPTE 233-1998 Copyright 2003 by THE SOCIETY OF MOTION PICTURE AND TELEVISION ENGINEERS 595 W. H

    8、artsdale Ave., White Plains, NY 10607 (914) 761-1100 Approved October 20, 2003 SMPTE STANDARD for Motion-Picture Film (16-mm) Projectable Image Area and Projector Usage SMPTE 233-2003 Page 2 of 4 pages Figure 1 Projectable image area on film as seen looking through the film toward the lens Table 1 D

    9、imensions Dimensions Inches Millimeters A 0.380 ref 0.380 ref B 0.286 max 0.286 max C 0.314 ref 0.314 ref D 0.122 min 0.122 min E 0.506 max 0.506 max F = H within 0.014 within 0.014 J = K nominally equal nominally equal 5 Emulsion position For original reversal film, the emulsion side shall be towar

    10、d the projection lens. For prints, the emulsion position is dependent upon the process of preparation and either emulsion to light source or emulsion to projection lens orientation may be encountered. (See figure 2 and note 5.) The actual emulsion position should be indicated on the leader and the f

    11、ilm container by notation or diagram. 6 Projection rate The standard frame rate for motion-picture projection is 24 frames per second. However, it is recognized that nonstandard frame rates are sometimes used for specific applications. For example: 24, 25, or 30 frames/s may be used for motion pictu

    12、res intended for television; higher or lower frame rates may be used for special effects and analysis, and nonstandard rates may be used for special motion-picture systems. A rate of 18 frames/s is often used for amateur silent films. The use of nonstandard frame rates requires notification and agre

    13、ement of all parties concerned with the use of the particular film. SMPTE 233-2003 Page 3 of 4 pages 7 Relationship between audio and picture The projection thread-up for motion-picture films containing an audio record shall place the audio-scanning point ahead (in the direction of film travel) of t

    14、he center of the picture being projected. Counting the frame in the projector aperture as zero, the audio-scanning point shall be opposite the center of the 26th frame for photographic audio or the 28th frame for magnetic audio, as specified in SMPTE 41 and SMPTE 112. If there is a significant dista

    15、nce between the average observer and the loudspeaker when the audio record is reproduced, the distance from the center of the projected aperture to the audio-scanning point may need to be shortened in the projector thread-up to bring the picture and audio into synchronization for the average observe

    16、r (because of the slower rate of travel of audio compared to that of light). If the average loudspeaker-to-audience distance is greater than 50 ft (15 m), the projector thread-up distance between projected picture and audio scan should be shortened by one frame for each nominal 50 ft of distance fro

    17、m loudspeaker to average audience. Figure 2 Film as seen from projector light source looking toward lens NOTES 1 Camera and printer apertures The actual image on the film is significantly larger than the maximum area intended for projection, so that in placement of the images throughout the sequence

    18、 of films, the tolerance is not restrictive of commercial practice. Upper limits have been established through consideration of good practice in avoiding overlap, encroachment upon areas reserved for audio records, flare from perforation edges, etc. Lower limits are similarly related to the avoidanc

    19、e of image effects at a defined edge, tolerances in film positioning, etc. 2 Projector aperture Dimensions B, D, and E in table 1 define the maximum image area on the film that is available for projection. They do not define the opening in the aperture plate of a projector. The size of this opening

    20、may differ from dimensions A and B, for example, because of the physical separation necessary between the aperture plate and the film to avoid scratching the film, or the slant of the marginal rays accepted by the lens. 3 Actual projected area It is recognized that, in many cases, the actual film im

    21、age area that is projected may be smaller than the projectable maximum and, in some cases, may be nonrectangular (for example, an irregular four-sided figure bound by either straight or curved lines). Such departures may result from equipment considerations such as slight inconsistencies among lense

    22、s, screen sizes, etc; from geometric limitations such as the screen surface being at an angle other than 90 from the SMPTE 233-2003 Page 4 of 4 pages projection axis, or being nonplanar, or both; and from aesthetic considerations such as pictorial composition within more restrictive image limits. In

    23、 the absence of specific instructions to the contrary, it is intended that the actual projected film image area be the largest appropriately-shaped figure that can be inscribed within the specified dimensions. When the picture outline on the screen is defined by the projector aperture, it is customa

    24、ry to round the corners of the projected film area. A maximum corner radius of 0.020 in (0.51 mm) at the film plane is recommended. 4 Film perforations Film intended for projection with this image area is normally perforated as specified in ANSI/SMPTE 109. 5 Contact prints When a relatively small nu

    25、mber of prints is required, contact prints are often made from 16-mm original materials, resulting in the emulsion position toward the light source. The majority of 16-mm release prints are printed by contact from a 16-mm intermediate or by reduction from a 35-mm intermediate in order to protect the

    26、 originals. The resulting prints generally have the emulsion side toward the projection lens. This permits intercutting of prints and originals without requiring a change of picture or sound focus during projection. Annex A (informative) Additional data A.1 Centerlines The centerlines of the image a

    27、rea are given for convenience in interpreting the standard, facilitating such applications as the optical design of equipment, and assisting in the understanding of suitable mechanical embodiments related to projectable image area. A.2 Projectable image area Essentially, the entire image within the

    28、maximum established by this standard will be transferred in such operations as reduction or enlargement printing (SMPTE RP 65), for television broadcasting (SMPTE 96), etc. Since the entire area will be presented, it is important that the projectable area include only material that meets recognized

    29、standards for technical and artistic excellence. A.3 Image area for television It is recognized that home television receivers are adjusted to show a distribution of picture sizes, ranging downward from the maximum. Guides to picture composition, based upon a statistical survey of receivers in use,

    30、are presented in SMPTE RP 27.3. Note that some portion of the audience will see the entire transmitted area, but for certainty in presentation of critical information over broadcast television, such information should be confined to a smaller, central area. Annex B (informative) Bibliography ANSI/SM

    31、PTE 48-1995, Motion-Picture Film (16-mm) Picture and Sound Contact Printing Printed Areas ANSI/SMPTE 109-1998, Motion-Picture Film (16-mm) Perforated 1R and 2R SMPTE 7-1999, Motion-Picture Film (16-mm) Camera Aperture Image and Usage SMPTE 96-1999, Television 35- and 16-mm Motion-Picture Film Scanned Image Area SMPTE RP 27.3-1989, Specifications for Safe Action and Safe Title Areas Test Pattern for Television Systems SMPTE RP 65-2000, Motion-Picture Enlargement/Reduction Ratios


    注意事项

    本文(SMPTE ST 233-2003 Motion-Picture Film (16-mm) - Projector Image Area and Projector Usage.pdf)为本站会员(bonesoil321)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开