1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21308-4 SANS 5183-2:2008Edition 2ISO 5183-2:2000Edition 2SOUTH AFRICAN NATIONAL STANDARD Resistance spot welding Electrode adaptors, male
4、taper 1:10 Part 2: Parallel shank fixing for end-thrust electrodes This national standard is the identical implementation of ISO 5183-2:2000 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lategan road groenkloof priv
5、ate bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 5183-2:2008 Edition 2 ISO 5183-2:2000 Edition 2 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committ
6、ee StanSA TC 5120.08, Welding and allied processes, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in June 2008. This SANS document supersedes SABS ISO 5183-2:1988 (first edition). Reference numberISO 518
7、3-2:2000(E)ISO 2000INTERNATIONALSTANDARDISO5183-2Second edition2000-12-01Resistance spot welding Electrodeadaptors, male taper 1:10 Part 2:Parallel shank fixing for end-thrustelectrodesquipement de soudage par rsistance Allonges dlectrode emboutamovible, cne mle 1:10 Partie 2: Emmanchement cylindriq
8、ue pour pousse en boutSANS 5183-2:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 5183-2:2000(E)PDF disclaimerThis PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed
9、 but shall notbe edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading thisfile, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this
10、area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameterswere optimized for printing. Every care has been taken to ensure that the file is suitable for use b
11、y ISO member bodies. In the unlikely eventthat a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2000All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electron
12、icor mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member bodyin the country of the requester.ISO copyright officeCase postale 56 Gb7 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.chWeb w
13、ww.iso.chPrinted in Switzerlandii ISO 2000 All rights reservedSANS 5183-2:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 5183-2:2000(E) ISO 2000 All rights reserved iiiForewordISO (the International Organization for Standardization)
14、is a worldwide federation of national standards bodies (ISOmember bodies). The work of preparing International Standards is normally carried out through ISO technicalcommittees. Each member body interested in a subject for which a technical committee has been established hasthe right to be represent
15、ed on that committee. International organizations, governmental and non-governmental, inliaison with ISO, also take part in the work. ISO collaborates closely with the International ElectrotechnicalCommission (IEC) on all matters of electrotechnical standardization.International Standards are drafte
16、d in accordance with the rules given in the ISO/IEC Directives, Part 3.Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Atte
17、ntion is drawn to the possibility that some of the elements of this part of ISO 5183 may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.International Standard ISO 5183-2 was prepared by Technical Committee ISO/TC 44, Welding and allied
18、processes, Subcommittee SC 6, Resistance welding.This second edition cancels and replaces the first edition (ISO 5183-2:1988), which has been technically revised.ISO 5183 consists of the following parts, under the general title Resistance spot welding Electrode adaptors,male taper 1:10:Gbe Part 1: C
19、onical fixing, taper 1:10Gbe Part 2: Parallel shank fixing for end thrust electrodesSANS 5183-2:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .SANS 5183-2:2008This s tandard may only be used and printed by approved subscription and freem
20、ailing clients of the SABS .INTERNATIONAL STANDARD ISO 5183-2:2000(E) ISO 2000 All rights reserved 1Resistance spot welding Electrode adaptors, male taper 1:10 Part 2:Parallel shank fixing for end-thrust electrodes1 ScopeThis part of ISO 5183 specifies the dimensions and tolerances of resistance spo
21、t welding electrode adaptors wherethe fixing element for the cap (see ISO 5821) is a male taper of 1:10 and a parallel shaft is used to fix the adaptorto the electrode holder in accordance with ISO 8430-3.2 Normative referencesThe following normative documents contain provisions which, through refer
22、ence in this text, constitute provisions ofthis part of ISO 5183. For dated references, subsequent amendments to, or revisions of, any of these publicationsdo not apply. However, parties to agreements based on this part of ISO 5183 are encouraged to investigate thepossibility of applying the most re
23、cent editions of the normative documents indicated below. For undatedreferences, the latest edition of the normative document referred to applies. Members of ISO and IEC maintainregisters of currently valid International Standards.ISO 5182:1991, Welding Materials for resistance welding electrodes an
24、d ancillary equipment.ISO 5821:1979, Resistance spot welding electrode caps.ISO 8430-3: 1988, Resistance spot welding Electrode holders Part 3: Parallel shank fixing for end thrust.3 DimensionsThe dimensions shall be those given in Figure 1 and Table 1.4 DesignationThe designation of electrode adapt
25、ors which comply with this part of ISO 5183 shall include the following:a) the description block (i.e. “spot welding electrode adaptor“);b) reference to this part of ISO 5183, i.e. ISO 5183-2;c) the type of electrode adaptor, in accordance with Figure 1;d) the diameter, d1, in millimetres;e) the len
26、gth, l1, in millimetres;f) the material of which the electrode adaptor is made, in accordance with ISO 5182.SANS 5183-2:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 5183-2:2000(E)2 ISO 2000 All rights reservedEXAMPLE A type C spot
27、welding electrode adaptor, of diameter d1= 16 mm, length l1= 68 mm and material type A 2/1,shall be designated as follows:Spot welding electrode adaptor ISO 5183-2 - C - 16 Gb4 68 - A 2/15 MaterialsThe material of which the electrode adaptor is made shall be in accordance with ISO 5182:1991, prefera
28、blygroup A, type 2.6 MarkingElectrode adaptors complying with this part of ISO 5183 shall be marked with the designation laid down in clause 4,but excluding the description block and the reference number of this part of ISO 5183, e.g.:A-16Gb4 68 - A 2/1SANS 5183-2:2008This s tandard may only be used
29、 and printed by approved subscription and freemailing clients of the SABS .ISO 5183-2:2000(E) ISO 2000 All rights reserved 3Dimensions in millimetresSurface roughness values in micrometresa) Type C: Straight adaptor with cooling hole open on one sideb) Type D: Straight adaptor with cooling hole open
30、 on both sidesc) Type E: Double cranked adaptorNOTE Figure c) does not show the cooling hole. However, the adaptor can be provided with cooling hole open on one side,liketypeC,oropenonbothsides,liketypeD.aCone diameter at the gauge plane.bOver this length the surface shall be neither damaged nor mar
31、ked.cGauge plane.dElectrode cap, see ISO 5821.eElectrode holder, see ISO 8430-3.Figure 1 Electrode adaptorsSANS 5183-2:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 5183-2:2000(E)4 ISO 2000 All rights reservedTable 1 Dimensions for
32、adaptors type C, D and EDimensions in millimetresl1d1d2ad3e l2l3for l5b=h11 Gb1 0,5 40 50 63 80 100 125 (140) 160 (180) 20012,5 10 6,5 12,5 6,5 9 68,5c78,5 91,5 108,5 128,5 153,5 16 12 8 16 8 11 68c78c91 108 128 153 168 188 20 15 10,5 20 10 14 78c91c108 128 153 168 188 208 228aCone diameter at the gauge plane.bValues given in parentheses are non-preferred.cValue that does not apply to type E.SANS 5183-2:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .
