1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21968-0 SANS 16147:2008 Edition 1 ISO 16147:2002 Edition 1SOUTH AFRICAN NATIONAL STANDARD Small craft Inboard diesel engines Engine-mounte
4、d fuel and electrical components This national standard is the identical implementation of ISO 16147:2002, and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: +
5、27 12 428 7911 fax: +27 12 344 1568 www.sabs.co.za SABS This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 16147:2008 Edition 1 ISO 16147:2002 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was
6、approved by National Committee SABS TC 188, Small craft, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in August 2008. This standard may only be used and printed by approved subscription and freemai
7、ling clients of the SABS. Reference number ISO 16147:2002(E) ISO 2002INTERNATIONAL STANDARD ISO 16147 First edition 2002-10-15 Small craft Inboard diesel engines Engine-mounted fuel and electrical components Petits navires Moteurs intrieurs diesels lments des circuits dalimentation et des systmes le
8、ctriques fixs sur le moteur SANS 16147:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 16147:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or vi
9、ewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability i
10、n this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable
11、 for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any mea
12、ns, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyr
13、ightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2002 All rights reservedSANS 16147:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 16147:2002(E) ISO 2002 All rights reserved iiiForeword ISO (the International Organization for St
14、andardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the rig
15、ht to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International
16、 Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as a
17、n International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such paten
18、t rights. ISO 16147 was prepared by Technical Committee ISO/TC 188, Small craft. SANS 16147:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 16147:2008This standard may only be used and printed by approved subscription and freemailing c
19、lients of the SABS.INTERNATIONAL STANDARD ISO 16147:2002(E) ISO 2002 All rights reserved 1Small craft Inboard diesel engines Engine-mounted fuel and electrical components 1 Scope This International Standard establishes requirements for the design and installation of engine-mounted fuel and electrica
20、l components on diesel inboard-mounted engines for minimizing fuel leakage and the risk of and/or the spread of fire on small craft of hull length up to 24 m. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of t
21、his International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative
22、 documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 7840:1994, Small craft Fire-resistant fuel hoses ISO 10088:2001, Small craft Permanently ins
23、talled fuel systems and fixed fuel tanks ISO 10133:2000, Small craft Electrical systems Extra-low-voltage d.c. installations 3 Terms and definitions For the purposes of this International Standard, the following terms and definitions apply. 3.1 engine-mounted component fixed to the marine inboard en
24、gine and which will be in place while the engine is in operation 3.2 diesel fuel hydrocarbon fuel or blends of hydrocarbon fuels which are liquids at atmospheric pressure and are used in compression-ignition engines 3.3 diesel engine compression-ignition engine in which ignition is obtained by means
25、 of compressing the diesel fuel/air mixture 3.4 accessible capable of being reached for inspection, removal or maintenance without removal of the permanent boat structure NOTE Hatches are not regarded as permanent boat structures in this sense, even if tools are needed to open them. SANS 16147:2008T
26、his standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 16147:2002(E) 2 ISO 2002 All rights reserved3.5 low-pressure fuel line hose or pipe for fuel supply to high-pressure pumps or injection pumps including leak-off and return pipes from high-press
27、ure pumps, injection pumps, injectors, etc. 3.6 high-pressure fuel pipe fuel pipes from high-pressure pumps or injection pumps including high-pressure accumulators (rails) 4 General All material and components shall be suitable for use in a marine atmosphere and capable of operation within an ambien
28、t temperature range of 10 C to + 80 C without failure or leakage, and be capable of being stored without operation within an ambient temperature range of 30 C to + 80 C without failure or leakage. 5 Engine fuel system and components 5.1 General 5.1.1 Engine-mounted fuel and lubricating systems shall
29、 be leak free, such that there is no dripping or wetting of surface areas at the interface of connecting components and pipe joints due to misting atomization, or liquid from fuel or lubrication under normal operation. 5.1.2 All materials used in fuel systems shall be resistant to deterioration by t
30、he fuel and to other liquids or compounds with which they may come into contact under normal operating conditions, e.g. grease, lubricating oil, bilge solvents and sea water. 5.1.3 All sealing material, such as gaskets, o-rings, joint-rings, etc. shall be of the non-wicking, i.e non-fuel- absorbent
31、type. 5.1.4 Fuel filters and flexible hoses shall, individually or as installed, withstand a 2,5 min fire test as described in ISO 10088:2001, annex B or ISO 7840:1994, annex A. 5.2 High-pressure pipes 5.2.1 High-pressure pipes shall be suitable for the pressure and pressure impulses in the sytem an
32、d shall be made of, for example, welded or solid drawn-steel pipes. 5.2.2 High-pressure pipes shall be secured to prevent vibrations leading to pipe fracture at all operating engine speeds. 5.3 Low-pressure fuel lines 5.3.1 Low-pressure fuel lines shall be made of seamless copper or copper alloys, s
33、tainless steel, or corrosion-resistant coated mild steel pipe with a high temperature (450 C or above) soldered or brazed end forms, or male/female straight-in pipes with compression-ring sealings and screwed compression connections, or flexible hose meeting the requirements of ISO 7840 secured by a
34、 metal hose clamp or permanently installed end fittings, such as a swaged sleeve, threaded insert or connections with compression ring sealings. 5.3.2 Hose connections having a nominal diameter of more than 25 mm shall have two hose clamps. The spud shall be at least 35 mm long, to provide space for
35、 the clamps. SANS 16147:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 16147:2002(E) ISO 2002 All rights reserved 35.3.3 All low-pressure pipes shall be secured into position so as to prevent damage due to excessive vibration leading t
36、o pipe fracture. All flexible hoses shall be located away from non-insulated components with a surface temperature above 200 o C, but remain accessible for inspection and maintenance. 5.4 Fuel filters Fuel filters shall be independantly supported to avoid stress on pipe connections, be readily acces
37、sible, and not be mounted above turbochargers or uncooled exhaust gas manifolds. 6 Electrical systems and components of engines 6.1 D.C. installations The d.c. negative ground/earth for electrical systems shall be a fully insulated earth return, or a ground earth return. 6.2 Cranking motors Earth-re
38、turn cranking motors shall be earthed (d.c. negative ground/earth) to the earth return system of the engine. 6.3 Wiring and connections 6.3.1 Cables and wiring shall be sized in accordance with ISO 10133. 6.3.2 Cables, wires and looms shall be of adequate length to prevent stressing of the cable and
39、 connections and chafing of the insulation, kept and secured well clear of rotating-shaft couplings, belts, etc., and supported to minimize the effects of vibration and chafing. 6.3.3 Wiring connections shall have the following protection: IP 67 as a minimum, if exposed to short-term immersion; IP 5
40、5 as a minimum, if exposed to splashing water; IP 20 as a minimum, if located in protected locations inside the craft. 6.4 Relays, fuse boxes and electronic control modules (ECMs) Relays, fuses and ECMs shall have the following protection or be enclosed in boxes having the same protection level: IP
41、67 as a minimum, if exposed to short-term immersion; SANS 16147:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 16147:2002(E) 4 ISO 2002 All rights reserved IP 55 as a minimum, if exposed to splashing water; IP 20 as a minimum, if located in protected locations inside the craft. SANS 16147:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.
