欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE USCAR-8-2013 Grain Flow Pattern for Bolts Screws and Studs (Revision 3)《螺栓和螺钉的颗粒流动模式》.pdf

    • 资源ID:1028413       资源大小:930.84KB        全文页数:9页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE USCAR-8-2013 Grain Flow Pattern for Bolts Screws and Studs (Revision 3)《螺栓和螺钉的颗粒流动模式》.pdf

    1、 Grain Flow Pattern for Bolts, Screws, and StudsSAE/USCAR-8 Revision 3 December 2013 ISBN: 978-0-7680-8115-2 _ The research data, analysis, conclusion, opinions and other contents of this document are solely the product of the authors. Neither the SAE International (SAE) nor the United States Counci

    2、l for Automotive Research (USCAR) certifies the compliance of any products with the requirements of nor makes any representations as to the accuracy of the contents of this document nor to its applicability for purpose. It is the sole responsibility of the user of this document to determine whether

    3、or not it is applicable for their purposes. Copyright 2013 USCAR Printed in U.S.A. All rights reserved. QUESTIONS REGARDING THIS DOCUMENT: (248) 273-2470 FAX (248) 273-2494 TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX (724) 776-0790 SUMMARY OF CONTENTS 1. SCOPE 2 2. TEST PROCEDURE 2 3. GRAIN FLOW P

    4、ATTERN REQUIREMENTS 2 4. REVERIFICATION . 2 5. REFERENCES 2 6. KEY WORDS . 2 SAE/USCAR-8 REVISION 3 Issued 1998-12 Revised 2013-12 Grain Flow Pattern for Bolts, Screws, and Studs SAE/USCAR-8 REVISION 3 Revised 2013-12 GRAIN FLOW PATTERN FOR BOLTS, SCREWS, AND STUDS - 2 - 1. SCOPE: This specification

    5、 covers the grain flow pattern requirements in headed bolts, screws, and studs. The heading practice in the manufacture of the bolt, screw, or stud sets the grain flow pattern, but it is also greatly influenced by the fastener design. 2. TEST PROCEDURE: 2.1 Testing for grain flow shall be performed

    6、after heading, prior to heat treatment, and subsequent processing of parts. After heat treatment the determination of the acceptability of grain flow is very subjective and shall not be used as primary manufacturing inspection method. NOTE: $IWHUHWFKLQJDOLJKWUHYHDOSROLVKRQDGLDPRQG wheel has the effe

    7、ct of knocking back some of the raised areas on the flow line ridges. This process improves the contrast between the darker root of the etch flow line, and the lightened or polished crests to improve evaluation. 2.2 The head and shank shall be sectioned approximately on the centerline, with the shan

    8、k having a minimum length of 1.0 X the diameter of the shank. 2.3 Macroetch the sectioned head and shank sufficient to reveal the grain flow pattern, using etching practice based upon ASTM E340, and shown in the manufacturers control plan. Grain flow samples shall be viewed at sufficient magnificati

    9、on to allow for adequate resolution of the grain flow lines. 2.4 The sample size and frequency for the above testing shall be identified in the manufacturers control plan. 3. GRAIN FLOW PATTERN REQUIREMENTS: 3.1 Grain flow throughout the product shall be continuous and uninterrupted except in those

    10、instances where a flash trim line has been determined to be acceptable. A continuous and uninterrupted grain flow must be maintained around the fillets and radii, but may be compressed. Grain flow lines terminating in head to shank fillets, radii, or onto the shank surface are not acceptable. In ups

    11、et parts, the entire material compression zone in the head shall be above the head to shank radius. Figures #1, #2 and #3 show the acceptable grain flow pattern typical in flange heads. Figures #4 and #5 show the unacceptable grain flow pattern typical in flange heads for comparison. All Figures rep

    12、resent a flange headed product. However, the grain flow principles and requirements apply to all head shapes. 4. REVERIFICATION: Changes in design or processing that effect grain flow pattern require re-verification. 5. REFERENCES: ASTM E340 6. KEY WORDS: End Grain, Compression Zone, Grain Flow. SAE

    13、/USCAR-8 REVISION 3 Revised 2013-12 GRAIN FLOW PATTERN FOR BOLTS, SCREWS, AND STUDS - 3 - FIGURE 1 - ACCEPTABLE GRAIN FLOW PATTERN SAE/USCAR-8 REVISION 3 Revised 2013-12 GRAIN FLOW PATTERN FOR BOLTS, SCREWS, AND STUDS - 4 - FIGURE 2 - ACCEPTABLE GRAIN FLOW PHOTOGRAPH SAE/USCAR-8 REVISION 3 Revised 2

    14、013-12 GRAIN FLOW PATTERN FOR BOLTS, SCREWS, AND STUDS - 5 - FIGURE 3 MARGINALLY ACCEPTABLE GRAIN FLOW PHOTOGRAPH Marginal but acceptable SAE/USCAR-8 REVISION 3 Revised 2013-12 GRAIN FLOW PATTERN FOR BOLTS, SCREWS, AND STUDS - 6 - FIGURE 4 - UNACCEPTABLE GRAIN FLOW PATTERN SAE/USCAR-8 REVISION 3 Revised 2013-12 GRAIN FLOW PATTERN FOR BOLTS, SCREWS, AND STUDS - 7 - FIGURE 5 UNACCEPTABLE GRAIN FLOW PHOTOGRAPH


    注意事项

    本文(SAE USCAR-8-2013 Grain Flow Pattern for Bolts Screws and Studs (Revision 3)《螺栓和螺钉的颗粒流动模式》.pdf)为本站会员(terrorscript155)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开