欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE J 934-1998 Vehicle Passenger Door Hinge Systems (Reissued).pdf

    • 资源ID:1027325       资源大小:74.67KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE J 934-1998 Vehicle Passenger Door Hinge Systems (Reissued).pdf

    1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefro

    2、m, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8512 FAX: (724) 776-0243TO PLACE A DOCUMENT

    3、 ORDER; (724) 776-4970 FAX: (724) 776-0790SAE WEB ADDRESS http:/www.sae.orgCopyright 1998 Society of Automotive Engineers, Inc.All rights reserved. Printed in U.S.A.SURFACEVEHICLE400 Commonwealth Drive, Warrendale, PA 15096-0001RECOMMENDEDPRACTICESubmitted for recognition as an American National Sta

    4、ndardJ934REI.SEP1998Issued 1965-07Reissued 1998-09Superseding J934 JUN97Vehicle Passenger Door Hinge Systems1. ScopeThe scope of this SAE Recommended Practice is to establish recommended uniform test proceduresand minimum static load requirements for vehicle passenger door hinge systems. Tests are d

    5、escribed thatcan be conducted on test fixtures and equipment in laboratory test facilities.The test procedures and minimum performance requirements outlined in this document are based on currentlyavailable engineering data. It is intended that all portions of the document be periodically reviewed an

    6、drevised as additional knowledge regarding vehicle hinge system performance under impact conditions isdeveloped.2. ReferencesThere are no referenced publications specified herein.3. Definitions3.1 Hinge SystemThat system used to position the door relative to the body structure and control the path o

    7、fthe door swing for passenger ingress and egress.3.2 Hinge AssemblyThat portion of the hinge assembly comprised of a pair of pivotally interconnected hingemembers.3.3 Hinge Components3.3.1 DOOR MEMBERThat portion of the hinge assembly normally affixed to the door structure and constitutingthe swingi

    8、ng member.3.3.2 BODY MEMBERThat portion of the hinge assembly normally affixed to the body structure and constitutingthe fixed member.3.3.3 HINGE PINThat portion of the hinge assembly normally interconnecting the body and door members andestablishing the swing axis.SAE J934 Reissued SEP1998-2-4. Bas

    9、ic Requirements4.1 Longitudinal LoadA vehicle passenger door hinge system, when tested as prescribed under test procedurein 5.1, must be capable of withstanding an ultimate longitudinal load of 11 100 N.4.2 Transverse LoadA vehicle passenger door hinge system, when tested in accordance with the test

    10、procedures in 5.2, must be capable of withstanding an ultimate transverse load of 8900 N.5. Static Tests5.1 Longitudinal Load5.1.1 PURPOSETo determine the ability of the vehicle hinge system to withstand a test load in the longitudinalvehicle direction.5.1.2 EQUIPMENTa. Tensile testing machine.b. A

    11、typical static test fixture is illustrated in Figure 1.FIGURE 1STATIC LOAD FIXTURES (TRANSVERSE LOAD)SAE J934 Reissued SEP1998-3-5.1.3 OPERATIONa. Attach a test fixture to the mounting provision of the hinge system. Hinge attitude must simulatevehicle position (door fully closed) relative to the hin

    12、ge centerline. For test purposes, the distancebetween the extreme end of one hinge in the system to the extreme end of another hinge in the systemis to be set at 406 mm. The load is to be applied equidistant between the linear center of the engagedportions of the hinge pin and through the centerline

    13、 of the hinge pin in the longitudinal vehicledirection.b. Apply the test load at a rate not to exceed 50 mm/min until failure. Failure to consist of separation ofeither hinge. Record maximum load.5.2 Transverse Load5.2.1 PURPOSETo determine the ability of the vehicle hinge system to withstand a test

    14、 load in the transversevehicle direction.5.2.2 EQUIPMENTa. Tensile testing machine.b. A typical static test fixture is illustrated in Figure 1.5.2.3 OPERATIONa. Attach the test fixture to the mounting provisions of the vehicle hinge system. Hinge attitude mustsimulate vehicle position (door fully cl

    15、osed) relative to the hinge centerline. For test purposes, thedistance between the extreme end of one hinge in the system to the extreme opposite end of anotherhinge in the system is to be set at 406 mm. The load is to be applied equidistant between the linearcenter of the engaged portions of the hi

    16、nge pins and through the centerline of the hinge pin in thetransverse vehicle direction.b. Apply the test load at a rate not to exceed 50 mm/min until failure. Failure to consist of separation ofeither hinge. Record maximum load.6. Single Hinge Evaluation6.1 IntroductionIn some circumstances, it may

    17、 be necessary to conduct evaluations of individual hinges in ahinge system. In such cases, the results for an individual hinge, when tested in accordance with theprocedures in 6.2, shall be such as to indicate that system requirements in 4.1 and 4.2 are met. (Example: Anindividual hinge in a two-hin

    18、ge system must be capable of withstanding 50% of the load requirements of thetotal system.)6.2 Test Procedures6.2.1 LONGITUDINAL LOADAttach a test fixture to the mounting provision of the hinge. Hinge attitude mustsimulate the vehicle position (door fully closed) relative to the hinge centerline. Fo

    19、r test purposes, the load isto be applied equidistant between the linear center of the engaged portions of the hinge pin and through thecenterline of the hinge pin in the longitudinal vehicle direction.Apply the test load at a rate not to exceed 50 mm/min until failure (failure to consist of separat

    20、ion of eitherhinge). Record maximum load.SAE J934 Reissued SEP1998-4-6.2.2 TRANSVERSE LOADAttach the test fixture to the mounting provision of the vehicle hinge. Hinge attitude mustsimulate the vehicle position (door fully closed) relative to the hinge centerline. For test purposes, the load isto be

    21、 applied equidistant between the linear center of the engaged positions of the hinge pin and through thecenterline of the hinge pin in the transverse vehicle direction.Apply the test load at a rate not to exceed 50 mm/min until failure (failure to consist of separation of eitherhinge). Record maximu

    22、m load.PREPARED BY THE SAE LATCH AND HINGE SUBCOMMITTEESAE J934 Reissued SEP1998RationaleNot applicable.Relationship of SAE Standard to ISO StandardNot applicable.ApplicationThe scope of this SAE Recommended Practice is to establish recommended uniform testprocedures and minimum static load requirem

    23、ents for vehicle passenger door hinge systems. Tests aredescribed that can be conducted on test fixtures and equipment in laboratory test facilities.The test procedures and minimum performance requirements outlined in this recommended practice arebased on currently available engineering data. It is

    24、intended that all portions of the recommendedpractice be periodically reviewed and revised as additional knowledge regarding vehicle hinge systemperformance under impact conditions is developed.Reference SectionThere are no referenced publications specified herein.Developed by the SAE Latch and Hinge Subcommittee


    注意事项

    本文(SAE J 934-1998 Vehicle Passenger Door Hinge Systems (Reissued).pdf)为本站会员(sumcourage256)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开