1、 AEROSPACE STANDARD BOLT, MACHINE-DOUBLE HEXAGON, EXTENDED WASHER HEAD, DRILLED, CORROSION AND HEAT RESISTANT NICKEL ALLOY, .1900-32 UNJF-3A AS9705Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any
2、form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: h
3、ttp:/www.sae.org ISSUED1999-08 REAFFIRMED2005-05 REVISED2017-09THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.DFEDERAL SUPPLY CLASS 5306 AS9705 SHEET 1 OF 2 REV. D PROCUREMENT SPECIFICATION: AS7471 SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the state oftechnicalan
4、d engineering sciences.The use ofthisreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAE reviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe revised,reaffirmed,stabilize
5、d,orcancelled.SAEinvitesyourwritten commentsandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS9705D RATIONALE THIS IS A LIMITED SCOPE REVISION. DRAWING NOTE 1 REVISED TO CORRECT DATUM CALLOUTS. NOTICE THE INITIAL SAE PUBLICATIO
6、N OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9705A, AMENDMENT 1, NOTICE 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPLS) MAY CONTINUE TO BE MANDATORY FOR DOD CO
7、NTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - BOLT AEROSPACE STANDARD AS9705 SHEET 2 OF 2 REV. D BOLT, MACHINE-DOUBLE HEXAGON, EXTENDED WASHER HEAD, DRILLED, CORROSION AND HEAT RESISTANT NICKEL ALLOY, .1900
8、-32 UNJF-3A TABLE 1 - DASH NUMBERS AND DIMENSIONS PART NUMBER L K APPROX WEIGHT LB/100 PART NUMBER L K APPROX WEIGHT LB/100 MS9705-04 .365- .385 .072-.092 .68 MS9705-25 1.678-1.698 .998-1.058 1.57 MS9705-05 .428- .448 .072-.092 .73 MS9705-26 1.740-1.760 1.060-1.120 1.61 MS9705-06 .490- .510 .072-.09
9、2 .77 MS9705-27 1.802-1.822 1.122-1.182 1.64 MS9705-07 .552- .572 .072-.092 .81 MS9705-28 1.865-1.885 1.185-1.245 1.69 MS9705-08 .615- .635 .072-.092 .85 MS9705-29 1.990-2.010 1.310-1.370 1.78 MS9705-09 .678- .698 .072-.092 .90 MS9705-30 2.115-2.135 1.435-1.495 1.86 MS9705-10 .740- .760 .072-.120 .9
10、4 MS9705-31 2.240-2.260 1.560-1.620 1.94 MS9705-11 .802- .822 .122-.182 .98 MS9705-32 2.365-2.385 1.685-1.745 2.03 MS9705-12 .865- .885 .185-.245 1.02 MS9705-33 2.490-2.510 1.810-1.870 2.11 MS9705-13 .928- .948 .248-.308 1.06 MS9705-34 2.615-2.635 1.935-1.995 2.20 MS9705-14 .990-1.010 .310-.370 1.10
11、 MS9705-35 2.740-2.760 2.060-2.120 2.28 MS9705-15 1.052-1.072 .372-.432 1.15 MS9705-36 2.865-2.885 2.185-2.245 2.38 MS9705-16 1.115-1.135 .435-.495 1.19 MS9705-37 2.990-3.010 2.310-2.370 2.45 MS9705-17 1.178-1.198 .498-.558 1.23 MS9705-38 3.115-3.135 2.435-2.495 2.53 MS9705-18 1.240-1.260 .560-.620
12、1.27 MS9705-39 3.240-3.260 2.560-2.620 2.62 MS9705-19 1.302-1.322 .622-.682 1.31 MS9705-40 3.365-3.385 2.685-2.745 2.70 MS9705-20 1.365-1.385 .685-.745 1.36 MS9705-41 3.490-3.510 2.810-2.870 2.78 MS9705-21 1.428-1.448 .748-.808 1.40 MS9705-42 3.615-3.635 2.935-2.995 2.87 MS9705-22 1.490-1.510 .810-.
13、870 1.44 MS9705-43 3.740-3.760 3.060-3.120 2.95 MS9705-23 1.552-1.572 .872-.932 1.48 MS9705-44 3.865-3.885 3.185-3.245 3.04 MS9705-24 1.615-1.635 .935-.995 1.52 NOTES 1. FOR PART NUMBERS MS9705-04 THROUGH MS9705-12 DATUM Y SHALL BE REPLACED BY DATUM Z (THREAD PD). 2. MATERIAL: CORROSION AND HEAT RES
14、ISTANT NICKEL ALLOY AMS5708 (UNS N07001). 3. PROCUREMENT SPECIFICATION: AS7471. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417, SENSITIVITY LEVEL 2 MINIMUM. 5. HEAD TO SHANK FILLET SHALL BE COLD ROLLED, EXCEPT DASH NUMBER SIZES -12 AND SMALLER DO NOT REQUIRE FILLET ROLLING. 6. SURFACE TEXTURE: S
15、YMBOLS ARE PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 7. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 8. DIMENSIONS ARE IN INCHES. 9. DIMENSIONS AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 10. DO NOT USE U
16、NASSIGNED PART NUMBERS. 11. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THIS STANDARD MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED. 12. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE
17、TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
