1、 AEROSPACE STANDARD CLAMP SUPPORT, LOOP, CLAMP AS85052/4Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, withou
2、t the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2001-03REVISED 2008-07 REAFFIRMED 2015-04THIRD ANGLE PROJECTION CUS
3、TODIAN: G-3/G-3E REV.A FEDERAL SUPPLY CLASS 5340AS85052/4 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: AS85052 /9/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreportis entirelyvoluntary, andits
4、 applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments a
5、ndsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85052/4A RATIONALE AS85052/4A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. R .250 MIN CLEARANCE R .375 2X R .031 .500.005 R .031 .228.218A R
6、.031.040.003 .335(88) .218FIGURE 1 - CLAMP SUPPORT TABLE 1 - DIMENSIONAL TABULATION SIZE CODEFOR USE ONAS85052/1, /2, AND /3 A-1012 -10 TO -12 .470-1416 -14 TO -16 .530-1820 -18 TO -20 .700-2224 -22 TO -24 .820AEROSPACE STANDARD AS85052/4 SHEET 2 OF 2 REV. A CLAMP SUPPORT, LOOP, CLAMP NOTES: 1. MATE
7、RIALS: CLAMP SUPPORT - 17-7PH, CORROSION RESISTANT STEEL PER AMS5528, OR AMS5529. 2. HEAT TREATMENT: STRESS RELIEVE AND HEAT TREAT TO CONDITION TH1100 PER AMS2759/3 AFTER FORMING. 3. FINISH: REMOVE SCALE. PASSIVATE PER AMS2700, TYPE 2 OR 8. 4. IDENTIFICATION: MARK THE MANUFACTURERS NAME, TRADEMARK O
8、R CAGE NUMBER, THE COMPLETE STANDARD PART NUMBER AND DASH NUMBER FROM TABLE 1 PER AS478, METHOD 2A1. 5. BREAK EDGES: .003 TO .015 (UNLESS OTHERWISE SPECIFIED). 6. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCE: LINEAR DIMENSIONS X.XXX .016, ANGLES 2 7. EXAMPLE: AS85052/4 - 1416 SIZE COD
9、E (FROM TABLE 1) DOCUMENT NUMBER 8. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. /9/ PROCUREMENT SPECIFICATION: AS85052 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI)
10、 QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS85052 FOR THIS STANDARD. SEE FOR CURRENT QPL ON-LINE. 10. INTENDED USE: THESE CLAMP SUPPORTS ARE INTENDED FOR USE WITH AS85052/1, /2, /3 CLAMPS IN VERY HIGH VIBRATION APPLICATION AND AS A REPAIR TECHNIQUE IN PROBLEM AREAS. DO NOT USE THESE SUPPORTS UNLESS CL
11、AMP IS SUPPORTED TO THE TUBE CENTERLINE. SEE 6.4 OF AS85052 FOR RECOMMENDED INSTALLATION OF CLAMPS FOR VARIOUS VIBRATION AREAS. 11. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
