1、SAE Technical Standards Board Rules providethat: “This report is published by SAE to advancethe state oftechnical and engineering sciences.Theuse ofthis reportisentirelyvoluntary, andits applicability and suitability for any particularuse,including any patentinfringement arising therefrom,isthe sole
2、 responsibility of the user.”SAE reviews each technical reportatleastevery five years atwhich timeitmay bereaffirmed,revised, or cancelled.SAE invites your written comments and suggestions.SHEET 1 OF 3AS83519/1THIRD ANGLE PROJECTIONAEROSPACE STANDARDAS83519/1g44g54g54g56g40g39;#23#23#23;#23#23#23#23
3、#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23;#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23;#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23;#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23
4、;#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23;#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23;#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23#23;#23#23#23;#23#23#23;#23#23#23;#23#23#23;#23#23#23;#23#23#23;#23#23#23;#23#23#23g53g40g36g41g41g44g53g48g40g39;#23
5、#23#232009-04SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT FOR CABLESHAVING TIN OR SILVER PLATED SHIELDS (CLASS I)PREPARED BY SAE SUBCOMMITTEE AE-8C2FEDERAL SUPPLY CLASS 5940NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-S-83519
6、/1C, NOTICE 1 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-S-83519/1C, NOTICE 1. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPE
7、CIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE
8、PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCI
9、ATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical
10、/standards/AS83519/1 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT FOR CABLESHAVING TIN OR SILVER PLATED SHIELDS
11、(CLASS I)AEROSPACE STANDARDAS83519/1SHEET 2 OF 3AS83519/1THE COMPLETE REQUIREMENTS FOR PROCURNG THE SHIELD TERMNATION DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF MIL-S-83519.CABLE DIAMETER RANGE AND PREPARATION MEASUREMENTSTABLE I. CONSTRUCTION DETAILS.QUALIFICATION: FOR
12、QUALIFICATION PERIODIC TESTING CABLES SHALL BE IN ACCORDANCE WITH TABLE II. THE TERMINATIONS SHALL BE INSTALLED PER THE “ASSEMBLY TO CABLE” PARAGRAPH IN MIL-S-83519 USING THE APPLICABLE CONVECTION AND INFRARED HEAT SOURCES.MATERIAL: INSULATION SLEEVE: HEAT-SHRINKABLE, TRANSPARENT POLYVINYLIDENE FLUO
13、RIDE. SOLDER PREFORM AND FLUX: TYPE Sn 63SRMAP PER QQ-S-571. THERMAL INDICATOR: COLOR TO COLORLESS.TEMPERATURE RATING: -55 TO +150C.COMPATIBLE CABLE JACKETS: THESE TERMINATIONS WILL PROVIDE ENVIRONMENTAL RESISTANCE WHEN INSTALLED ON CABLES CONFORMING TO:1. MIL-C-27500 JACKET TYPES: .05, 08, 09, 10,
14、11, 12, 14, 15, 23 AND THEIR DOUBLE JACKET EQUIVALENTS.2. MIL-C-7078/1, /3, /8, /9, /10Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, EN
15、VIRONMENT RESISTANT FOR CABLESHAVING TIN OR SILVER PLATED SHIELDS (CLASS I)AEROSPACE STANDARDAS83519/1SHEET 3 OF 3AS83519/1NOTES:1. WHEN PERFORMING END STRIPPED CABLE SEALING THE BEST RESULTS ARE OBTAINED WHEN THE SMALLEST SIZE TERMINATION FOR THE CABLE/LEAD WIRE COMBINED IS USED. SEALABILITY ON CAB
16、LES WITH MORE THAN THREE PRIMARIES OF AWG 22 AND LARGER REQUIRES SPECIAL PRECAUTIONS.2. THE SPLICE IS RECOMMENDED FOR CABLES RATED AT 105C, IF SPECIAL PRECAUTIONS ARE TAKEN TO ISOLATE THE HEAT SOURCE FROM THE INSULATION.TABLE II. QUALIFICATION TEST CABLES.TABLE III. SUPERSESSION AND CROSS-REFERENCE.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
