1、AEROSPACE STANDARD REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE II, CLASS 2, COMPOSITION C, REMOVAL TOOL ONLY AS81969/28Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,
2、electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUE
3、D 2015-05THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120AS81969/28SHEET 1 OF 2PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeringsciences.The useofthis reportisentirel
4、yvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites you
5、rwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/28RATIONALE AS81969/28 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/28 WITH THIS DOCUMENT. IT INCLUDES ENGINEERING POSITION LETT
6、ERS, MILITARY SPECIFICATION AMENDMENTS, AND MINOR TECHNICAL CHANGES REQUIRED TO REFLECT THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS
7、81969. FIGURE 1 - REMOVAL TOOL M81969/28-01, -02 FIGURE 2 - REMOVAL TOOL M81969/28-03 AEROSPACE STANDARD AS81969/28SHEET 2 OF 2REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE II, CLASS 2, COMPOSITION C, REMOVAL TOOL ONLY REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST
8、ISSUE OF AS81969. 1. CONFIGURATION: TOOL CONFIGURATION SHALL BE IN ACCORDANCE WITH FIGURES 1 AND 2 AND TABLE 1. DIMENSIONING AND TOLERANCES IS IN ACCORDANCE WITH ANSI Y14.5M. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .005 ON THREE PLACE DECIMALS, .01 ON TWO PLACE DECIMALS AN
9、D 4q. METRIC EQUIVALENTS SHOWN IN PARENTHESES IS BASED ON 25.4 MILLIMETERS PER INCH. HANDLE CONFIGURATION OPTIONAL WITHIN MAXIMUM DIMENSIONS SHOWN (SEE FIGURES 1 AND 2). HANDLE AND TIP SHALL OPEN ON A SPRING LOADED HINGE WHICH ALLOWS THE TOOL TO OPEN FREELY AND CLOSE TO SURROUND THE WIRE/CONTACT WHE
10、N REMOVING IT FROM THE CONNECTOR. TABLE 1 - FIGURES 1 AND 2 DIMENSIONS M81969/28 CONTACT SIZE A DIA. B DIA. C 1/ D MAX E MAX HANDLECOLOR -01 5 .287/.285 (7.29/7.24) .261/.255 (6.63/6.48) .770/.730 (19.56/18.54) 3.064 (77.83) .900(22.86) YELLOW -02 12 .194/.186 (4.93/4.72) .159/.154 (4.04/3.91) .656/
11、.620 (16.66/15.75) RED1/ THE .030 AND .005 RADIUS METRIC DIMENSIONS ARE .762 AND .127 RESPECTIVELY. 2. IDENTIFICATION MARKING: EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON TOOL BODY IN ACCORDANCE WITH MIL-STD-130 (LOCATION OPTIONAL). TOOL IDENTIFICATION SHALL INCLUDE SAE PART NUMBER (SEE REQ
12、UIREMENT 4) AND SUPPLIER NAME OR SYMBOL ACCORDANCE WITH AIR1351. HANDLE COLOR SHALL BE IN ACCORDANCE WITH TABLE 1. 3. MATERIALS: HANDLE SHALL BE PLASTIC RESIN (FORMULATION OPTIONAL) OR ALUMINUM, ANODIZED TO PREVENT CORROSION. PROBE SHALL BE STAINLESS STEEL IN ACCORDANCE WITH ASTM 276 OR EQUIVALENT.
13、SPRING (NOT SHOWN IN FIGURE 1) SHALL BE STEEL IN ACCORDANCE WITH AS81969 (SEE CONFIGURATION REQUIREMENT). 4. PART IDENTIFICATION NUMBER (PIN): M81969 /28 -01 I I I I I I_ DASH NUMBER (SEE TABLE 1) I I_ DETAIL SPECIFICATION NUMBER I_ BASIC SPECIFICATION NUMBER APPLICATION NOTES: 1. TOOLS SHALL BE USE
14、D TO REMOVE CONTACTS IN CONNECTORS SPECIFIED IN TABLE 2. TABLE 2 - REMOVAL TOOL APPLICATIONS PART NUMBER AS81969/20 COAXIAL CONTACT SIZE CONNECTOR -01 5 AND 9 AS81659 SERIES 2 1/ -02 12 1/ TOOL USED WITH NON-STANDARD COAXIAL CONTACTS SIMILAR TO AS39029. 2. AS81969/28 DETAIL SPECIFICATION SUPERSEDES
15、THE MIL-I-81969/28 AND MIL-I-81969/28B (USAF) DETAIL SPECIFICATIONS. PART NUMBERS REMAIN UNCHANGED. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
