1、 AEROSPACE STANDARD INSTALLING TOOLS, CONNECTOR, ELECTRICAL CONTACT,(TYPE CR) TYPE I, CLASS 1, COMPOSITION A AS81969/13Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electr
2、onic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2015
3、-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120AS81969/13 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirel
4、yvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites your
5、writtencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/13 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO ALLOW THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/13 WITH THIS DOCUMENT, TO
6、UPDATE QUALIFICATION INFORMATION, TO REMOVE THE PATENT NOTICE SINCE THE PATENT HAS EXPIRED, TO IMPROVE DRAWING LEGIBILITY, AND TO UPDATE REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. FIGURE 1 -
7、INSTALLING TOOL CONFIGURATIONS/DIMENSIONS AEROSPACE STANDARD AS81969/13 SHEET 2 OF 2 INSTALLING TOOLS, CONNECTOR, ELECTRICAL CONTACT, (TYPE CR) TYPE I, CLASS 1, COMPOSITION A TABLE 1 - METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .002 0.05 .06 1.52 1.250 31.75 .003 0.0
8、8 .080 2.03 2.500 63.50 .022 0.56 .125 3.18 .040 1.02 .375 9.53 .050 1.27 .750 19.05REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. DESIGN: THE TOOL SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS IN TABLE
9、1 ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .015 INCH (0.38 MILLIMETERS). 2. MATERIAL AND FINISHES: HANDLE - ALUMINUM INSTALLING TIP - DRILL ROD HARDENED PLATING - HANDLE - NOT APPLICABLE, ANODIZED ONLY INSTALLING TIP
10、- DECORATIVE CHROME, .0001 INCH THICKNESS 3. PART NUMBER/MARKING: M81969/13-01 EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON THE HANDLE WITH THE MANUFACTURERS IDENTIFICATION AND PART NUMBER IN ACCORDANCE WITH MIL-STD-130. MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. 4. Q
11、UALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS81969 WITH THE FOLLOWING EXCEPTIONS: ROTATION - NOT APPLICABLE THRUST - NOT APPLICABLE IMPACT STRENGTH - NOT APPLICABLE ALTERNATIVE QUALIFICATION REQUIREMENTS SUCH AS CERTIFICATION, FIRST ARTICLE OR QC TESTING MAY BE IMPOSED BY THE QUALIFYING
12、 ACTIVITY (QA). THE QA SHALL SUBMIT A WRITTEN REQUEST TO THE AE-8C2 COMMITTEE FOR REVIEW AND APPROVAL OF THE ALTERNATIVE QUALIFICATION TESTING PROGRAM PRIOR TO IMPLEMENTATION OF THE REQUIREMENT. APPLICATION NOTES: 1. THIS TOOL SHALL BE USED TO INSTALL CONTACTS AS SPECIFIED IN MIL-DTL-28731/1 THROUGH
13、 /6 AND /9 THROUGH /18. 2. THIS DOCUMENT SUPERSEDES MIL-I-81969/13A DATED 11 JANUARY 1979 AND MIL-C-28731/21B DATED 17 MAY 1977. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
