1、 AEROSPACE STANDARD TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, ELECTRONIC, IN-LINE JUNCTION, INTEGRAL RESISTOR, SERIES I AS81714/22Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or
2、 by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/ww
3、w.sae.org ISSUED 2001-07REAFFIRMED 2012-01THIRD ANGLE PROJECTION CUSTODIAN: AE-8C2 FEDERAL SUPPLY CLASS 5940 AS81714/22SHEET 1 OF 4 SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirel
4、y voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites y
5、ourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81714/22 RATIONALE AS81714/22 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FR
6、OM U.S. MILITARY SPECIFICATION MIL-T-81714/22B AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-T-81714/22B. ANY PART NUMBERS ESTABLI
7、SHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RU
8、LES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION
9、 REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.AEROSPACE STANDARD AS81714/22SHEET 2 OF 4 TERMINAL JUNCTION SYSTEM, TERMINAL J
10、UNCTION BLOCKS, ELECTRONIC, IN-LINE JUNCTION, INTEGRAL RESISTOR, SERIES I THE COMPLETE REQUIREMENTS FOR ACQUIRING THE WIRE IN-LINE JUNCTION DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF SPECIFICATION MIL-T-81714.FIGURE 1. STYLE 1 ELECTRONIC IN-LINE JUNCTION.TABLE I. STYLE 1
11、 PART NUMBERS.AEROSPACE STANDARD AS81714/22SHEET 3 OF 4 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, ELECTRONIC, IN-LINE JUNCTION, INTEGRAL RESISTOR, SERIES I FIGURE 2. STYLE 2 ELECTRONIC IN-LINE JUNCTION.TABLE II. STYLE 2 PART NUMBERS.REQUIREMENTS:1. MATERIALS:a. CURRENT CARRYING MEMBERS OF
12、THE ELECTRONIC IN-LINE JUNCTION SHALL BE IN ACCORDANCE WITH THE IN-LINE JUNCTION SPECIFICATION.b. HOUSING SHALL BE COVERED BY SHRINK TUBING AND/OR SHROUDED WITH GROMMET MATERIAL.AEROSPACE STANDARD AS81714/22SHEET 4 OF 4 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, ELECTRONIC, IN-LINE JUNCTION
13、, INTEGRAL RESISTOR, SERIES I NOTES:1. DIMENSIONS ARE IN INCHES.2. MIL-T-81714 REQUIREMENTS APPLY TO BASIC IN-LINE JUNCTION ONLY. FOR RATING AND CHARACTERISTICS OF ELECTRONIC COMPONENT(S), CONSULT COMPONENT SPECIFICATION.3. TOOL FOR CONTACT INSERTING/REMOVAL SHALL BE ORDERED SEPARATELY.4. METRIC EQU
14、IVALENTS (TO THE NEAREST .01 MM) ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM.5. INTERNATIONAL INTEREST, SEE SPECIFICATION MIL-T-81714.6. THE PART NUMBER CONSISTS OF THE LETTER M, SPECIFICATION SHEET NUMBER, STYLE NUMBER (SEE FIGURES), IN-LINE JUNCTION CLASS D (SEE NOTE
15、 3), AND BUSSING DESIGNATOR (REF SPEC SHEET).PART NUMBER EXAMPLE:M81714/22-1D001IN-LINE JUNCTION, SIZE 22, STYLE 1, CLASS D WITH 001 CIRCUIT (ONE RLR07C101JM RESISTOR).7. CLASSES A, B AND C COMPONENTS ARE INACTIVE FOR NEW DESIGN. ONLY CLASS D COMPONENTS SHALL BE USED FOR DIRECT GOVERNMENT ACQUISITION.
