1、AEROSPACE STANDARD ACCESSORY, DUMMY STOWAGE RECEPTACLE, CONNECTOR, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING (FOR SERIES 2 CONNECTORS)AS81511/19Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval
2、 system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerSe
3、rvicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935 AS81511/19SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technic
4、alandengineering sciences. Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevi
5、sed,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/19RATIONALE THIS DETAIL SPECIFICATION SHEET IS WRITTEN TO PERMIT THE CANCELLATION AN
6、D SUPERSESSION OF MIL-C-81511/19 WITH THIS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - DUMMY STOWAGE RECEPTACLE AEROSPACE STANDARD AS81511/19SHEET 2 OF 3ACCESSORY, DUMMY STOWAGE RECEP
7、TACLE, CONNECTOR, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING (FOR SERIES 2 CONNECTORS)FIGURE 1A - DUMMY STOWAGE RECEPTACLE (DETAIL A) TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .003 0.08 .025 0.64
8、 .075 1.91 .295 7.49 .005 0.13 .031 0.79 .085 2.16 .315 8.00.006 0.15 .040 1.02 .090 2.29 .360 9.14 .009 0.23 .048 1.22 .094 2.39 .380 9.65.010 0.25 .060 1.52 .095 2.41 .465 11.81 .015 0.38 .065 1.65 .116 2.95 .485 12.32.016 0.41 .067 1.70 .126 3.20 .635 16.13 .021 0.53 .073 1.85 .230 5.84 .655 16.6
9、4TABLE 2 - FIGURE 1 DIMENSIONS/CONFIGURATION PARTNUMBER TEMP.RATING (C) APPLICABLECONNECTOR CLASSESSHELLSIZEADIA.BDIA.CDIA.GSQUARE HSQUARE YDIA.FF RAD. APPROX. WEIGHT (LB) M81511/19-08-1 175 E, W 8.392(9.96).386(9.80) .553(14.05) .547(13.89).301(7.65) .292(7.42) .820(20.83) .804(20.42) .599(15.21) .
10、589(14.96) .452(11.48) .444(11.28) .120(3.05).100(2.54) .0118 M81511/19-08-2 200 A, F M81511/19-10-1 175 E, W 10.517(13.13) .511(12.98).678(17.22) .672(17.07).426(10.82) .417(10.59).945(24.00) .929(23.60) .724(18.39) .714(18.14) .576(14.63) .568(14.43) .120(3.05).100(2.54) .0148 M81511/19-10-2 200 A
11、, F M81511/19-14-1 175 E, W 14.767(19.48) .761(19.33).928(23.57) .922(23.42).676(17.17) .667(16.94)1.133(28.78) 1.117(28.37) .911(23.14) .901(22.89) .826(20.98) .818(20.78) .120(3.05).100(2.54) .0200 M81511/19-14-2 200 A, F M81511/19-16-1 175 E, W 16.893(22.68) .887(22.53)1.054(26.77) 1.048(26.62).8
12、02(20.37) .793(20.14)1.258(31.95) 1.242(31.55) .974(24.74) .964(24.49) .951(24.16) .943(23.95) .150(3.81).130(3.30) .0230 M81511/19-16-2 200 A, F M81511/19-18-1 175 E, W 181.017(25.83) 1.011(25.68)1.178(29.92) 1.172(29.77).926(23.52) .917(23.29)1.351(34.32) 1.335(33.91) 1.067(27.10) 1.080(27.43) 1.0
13、75(27.31) 1.067(27.10) .150(3.81).130(3.30) .0250 M81511/19-18-2 200 A, F AEROSPACE STANDARD AS81511/19SHEET 3 OF 3ACCESSORY, DUMMY STOWAGE RECEPTACLE, CONNECTOR, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING (FOR SERIES 2 CONNECTORS)REQUIREMENTS: ALL REQUIREMENTS SHALL
14、 CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1. DESIGN: DUMMY STOWAGE RECEPTACLES SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 2. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UN
15、LESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. THIS RECEPTACLE MATES WITH AS81511/6 CONNECTORS. FOR SHELL SIZES 20, 22, AND 24, USE AS81511/30 CONNECTORS. 2. MATERIAL/PLATING: FINISH: 175 C - CADMIUM PLATE OVER NICKEL, OLIVE DRAB IN COLOR (FOR USE WITH CLASS E AND W CONNECTORS) 200 C - ELECTR
16、OLESS NICKEL (FOR USE WITH CLASS A AND F CONNECTORS) BODY: ALUMINUM ALLOY IN ACCORDANCE WITH AS81511 BAYONET PINS: CORROSION RESISTANT STEEL IN ACCORDANCE WITH AS81511 O-RING: SILICONE IN ACCORDANCE WITH AS81511 APPLICATION NOTES: 1. AS81511 CONNECTORS AND ACCESSORIES ARE NOT RECOMMENDED FOR NEW DES
17、IGN. SPECIFICATION NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL RE
18、VISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
