欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AS 6054-2001 Drum Metal - Shipping and Storage《金属桶 船运和存储》.pdf

    • 资源ID:1025057       资源大小:329.72KB        全文页数:20页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AS 6054-2001 Drum Metal - Shipping and Storage《金属桶 船运和存储》.pdf

    1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

    2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p

    3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

    4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS6054 AEROSPACE STANDARD AS6054 Issued 2001-03 Reaffirmed 2017-11 Drum, Metal-Shipping and Sto

    5、rage RATIONALE AS6054 has been reaffirmed to comply with the SAE Five-Year Review policy. NOTICEThis document has been taken directly from U.S. Military Specification MIL-D-6054F and contains only minor editorial and format changes required to bring it into conformance with the publishing requiremen

    6、ts of SAE technical standards. The initial release of this document is intended to replace MIL-D-6054F. Any part numbers established by the original specification remain unchanged.The original Military Specification was adopted as an SAE standard under the provisions of the SAE Technical Standards B

    7、oard (TSB) Rules and Regulations (TSB 001) pertaining to accelerated adoption of government specifications and standards. TSB rules provide for (a) the publication of portions of unrevised government specifications and standards without consensus voting at the SAE Committee level, and (b) the use of

    8、 the existing government specification or standard format.Under Department of Defense policies and procedures, any qualification requirements and associated qualified products lists are mandatory for DOD contracts. Any requirement relating to qualified products lists (QPLs) has not been adopted by S

    9、AE and is not part of this SAE technical document.1. SCOPE:1.1 Scope:This specification covers new cylindrical drums to be used as exterior shipping containers (see 6.1).1.2 Classification:Drums shall be furnished in the dimensions and capacities as specified in the applicable MS standards.2. APPLIC

    10、ABLE DOCUMENTS:2.1 Government documents:2.1.1 Specifications and standards: The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of D

    11、efense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation.SPECIFICATIONSFederalQQ-S-781 Strapping, Steel, and SealsPPP-C-1120 Cushioning Material, Uncompressed Bound Fiber for PackagingMilitaryMIL-R-3065 Rubber, Fabricated ProductMIL-R-6855 Rubber, Synth

    12、etic Sheets, Strips, Molded or Extruded ShapesMIL-I-26860 Indicator, Humidity, Plug, Color ChangeSTANDARDSFederalFED-STD-No. 595 ColorsSAE INTERNATIONAL AS6054 Page 2 of 20_ 2.1.1 (Continued):MilitaryMIL-STD-105 Sampling Procedures and Tables for Inspection by AttributesMIL-STD-129 Marking for Shipm

    13、ent and StorageMIL-STD-147 Palletized Unit LoadsMIL-STD-831 Test Reports, Preparation ofMS 27683 Drums, Metal-Shipping and Storage (16 to 80 gallons)MS 27684 Drums, Metal-Shipping and Storage (3 to 12 gallons)(Copies of specifications, standards, drawings, and publications required by manufacturers

    14、in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.)2.2 Other publications:The following document(s) form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of t

    15、he documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of the documents not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date of the solicitation.Ameri

    16、can Society for Testing and Materials (ASTM)A-109 Steel, Strip, Carbon, Cold-Rolled (DOD adopted)A-366 Steel, Sheet, Carbon, Cold-Rolled, Commercial Quality (DOD adopted)B-117 Salt Spray (FOG) Testing, Standard Method of (DOD adopted)D-610 Evaluating Degree of Rusting on Painted Steel Surfaces (DOD

    17、adopted)D-3951 Standard Practice for Commercial Packaging(Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.)(Nongovernment standards and other publications are normally available from the organizations which prepar

    18、e or which distribute the documents. These documents also may be available in or through libraries or other informational services.)2.3 Order of precedence:In the event of a conflict between the text of this specification and the references cited herein (except for associated detail specifications,

    19、specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained.SAE INTERNATIONAL AS6054 Page 3 of 20_ 3. REQUIREMENTS:3.1 MS sheets:The

    20、individual item requirements shall be as specified herein and in accordance with the applicable MS sheet. In the event of any conflict between the requirements of this specification and the MS sheet, the latter shall govern.3.2 First article:Unless otherwise specified, the supplier shall furnish two

    21、 samples for first article inspection and approval (see 4.4 and 6.3).3.3 Materials:Materials used in the manufacture of drums shall meet all requirements specified herein.3.3.1 Steel: Cold rolled steel sheets for bodies, covers and bottoms shall conform to ASTM A366. Cold rolled steel strips for lug

    22、s and locking rings shall be quarter-hard temper, edge condition No. 4, free from burrs and sharp edges, conforming to ASTM A 109. The gage of steel (per United States standard gage) specified in the applicable MS standards for the drum body, covers, bottoms and closure is the minimum thickness acce

    23、ptable. When thicker material than specified is used in the fabrication of drums, the increased thickness of material shall not be of such magnitude as to interfere with the interchangeability of drum parts (see 4.5.1).3.3.2 Gaskets: Gaskets shall be formed from synthetic rubber conforming to MIL-R-

    24、6855, Class 2, Grade 60, or MIL-R-3065, Grade SC-610F (see 4.5.4.1).3.4 Design and construction:The design of the drum body and component parts shall be in accordance with applicable MS standards (see 4.5.4).3.4.1 Cover: The container cover shall be style #1 (recessed). The 10.5, 13.81, 15.38, and 1

    25、8.25 inch diameters drums may also be procured with style #2 domed covers (see 6.2). Convexity of covers shall not extend beyond level of chime (see 4.5.4.1).3.4.2 Locking ring: The locking ring shall be either Style 1 or Style 2 as specified (see 4.5.4.1 and 6.2).SAE INTERNATIONAL AS6054 Page 4 of

    26、20_ 3.4.2.1 Style 1 locking ring: The locking ring shall be of the nut and bolt type. The bolt shall be a commercial standard 3/8-16 UNC-2A hex head with screw driver slot in hex head. The nut shall be a standard SAE hex nut or a commercial jam nut. Bolt heads and nuts shall be of a size that is com

    27、patible with standard hand and power tools. Nut and bolt shall be zinc or cadmium plated with tensile strength that meets the test requirements of this specification. The lugs shall not bend to attain a permanent set or crack when the required torque is applied. Provisions shall be provided for use

    28、of a lead and wire tamper-proof seal (see 4.5.4.1).3.4.2.2 Style 2 locking ring: The locking ring shall be a lever actuated type locking ring. The construction shall be sturdy enough to develop sufficient tension to completely seal the closure and withstand all tests required by this specification.

    29、Provisions shall be provided for use of a lead and wire tamper-proof seal (see 4.5.4.1).3.4.3 Humidity indicator: When specified (see 6.2), the drum body shall have provisions for accepting a humidity indicator conforming to MIL-I-26860, Type I, or Type II. The provision shall allow for a hermetic s

    30、eal between the container body and the indicator. The humidity indicator shall be located in the body at a point opposite the side seam and an equal distance between the hoops of the drum. Other locations may be specified by the procuring agency (see 4.5.4.1, 4.6.1, and 6.2).3.4.4 Handles: When spec

    31、ified (see 6.2), drums having an inside diameter of 22.5 inches or greater shall be equipped with two chest type drop handles located in the upper one third of the drum and equally spaced around the circumference. Each handle assembly shall be designed for the surface mounting with stops to hold the

    32、 bail perpendicular to the mounting plate when in carrying position. The bail shall have a minimum inside length of four inches and a minimum clearance of two inches from the bail perpendicular to the mounting plate. When tested in accordance with paragraph 4.5.5, the handle assembly shall be capabl

    33、e of supporting loaded drums without permanent distortion at extremities in excess of 1/4 inches from the horizontal (see 4.6.4).3.4.5 Dimensions: Dimensions shall be in accordance with the applicable MS standards (see 4.5.4.2).3.5 Finish:3.5.1 Conversion coatings: The interior and exterior surface

    34、of all drums, including the cover and locking rings, shall be clean and compatible with the conversion coating utilized (when required) for production of the end item (see 4.4.1).3.5.2 Protective coating: Unless otherwise specified, (see 6.2), coat all interior and exterior surfaces of the drum and

    35、component parts, except the closing bolt and gasket, with a rust inhibiting coating that withstands salt spray test requirements (see 3.4.2.1 and 4.3.1). Unless otherwise specified color shall conform to No. 24087 of FED-STD-595 (see 4.4.1 and 6.2).SAE INTERNATIONAL AS6054 Page 5 of 20_ 3.5.2.1 Salt

    36、 spray resistance: Results of the Salt Spray Test shall show no rust creepage, blistering, undercutting or loss of adhesion of the paint beyond 1/8 inch of the scribe mark. All other surfaces of the test specimens shall show no more than a trace of film failure, (Rust Grade 9 of ASTM D610), with non

    37、e larger than 1mm, (3/64 inch), in diameter (see 4.4.1).3.6 Performance:The drums shall not leak when tested in accordance with 4.6.1, 4.6.2, and 4.6.3.3.7 Container marking:3.7.1 Bottom and top: The bottom and top of the drum shall be embossed in accordance with Figure 1 (see 4.5.4.1).3.7.2 Body: U

    38、nless otherwise specified (see 6.2), the body of each container shall be marked on opposite sides with waterproof ink and letters at least one-half inch high. The marking shall appear three quarters of an inch below the lower edge of the locking ring. The color shall conform to color number 23538 of

    39、 FED-STD-595. The wording of the marking shall be as follows (see 4.5.4.1):REUSABLE CONTAINER DO NOT DESTROY3.8 Workmanship:The construction shall be of such quality that finished drums shall have no sharp burrs or rough surfaces. The metal shall be free of defects which may affect the durability, s

    40、trength, or serviceability of the drum. The gasket shall be uniformly distributed about the circumference of the cover and shall lie naturally with the flat surface parallel to the horizontal plane of the cover to provide a seal which will not leak. The protective coatings shall be applied in a unif

    41、orm manner (see 4.5.4.1).4. QUALITY ASSURANCE PROVISIONS:4.1 Responsibility for inspection:Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract

    42、 or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such

    43、 inspections are deemed necessary to assure supplies and services conform to prescribed requirements.SAE INTERNATIONAL AS6054 Page 6 of 20_ FIGURE 1. DRUM MARKINGSSAE INTERNATIONAL AS6054 Page 7 of 20_ 4.1.1 Responsibility for compliance: All items must meet all requirements of sections 3 and 5. The

    44、 inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted

    45、to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material.4.2 Classification of Inspection

    46、s:The inspection requirements specified herein are classified as follows:a. First article inspection (see 4.4).b. quality conformance inspection (see 4.5).4.3 Inspection conditions:Unless otherwise specified, all inspections shall be performed in accordance with the test conditions specified in the

    47、applicable test method document or the applicable paragraph(s) in this specification.4.4 first article examination and tests:Unless otherwise specified, two sample drums of each size specified in the procurement document shall be made available for first article examination and tests. They shall be examined for all provisions of this specification applicable to the end item inspection (see 4.5.4) and they shall be tested as follows:a. The two sample drums s


    注意事项

    本文(SAE AS 6054-2001 Drum Metal - Shipping and Storage《金属桶 船运和存储》.pdf)为本站会员(李朗)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开