欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AS 5778-1997 Covers Aircraft Components General Requirements for《飞机组件护盖的一般要求》.pdf

    • 资源ID:1024952       资源大小:238.47KB        全文页数:17页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AS 5778-1997 Covers Aircraft Components General Requirements for《飞机组件护盖的一般要求》.pdf

    1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

    2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p

    3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970

    4、 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS5778 AEROSPACESTANDARDAS5778 Issued 1997-08 Reaffirmed 2017-11 Covers, Aircraft Components, Gen

    5、eral Requirements For RATIONALE AS5778 has been reaffirmed to comply with the SAE Five-Year Review policy. NOTICEThis document has been taken directly from U.S. Military Specification MIL-C-5778D and contains only minor editorial and format changes required to bring it into conformance with the publ

    6、ishing requirements of SAE technical standards.The original Military Specification was adopted as an SAE standard under the provisions of the SAE Technical Standards Board (TSB) Rules and Regulations (TSB 001) pertaining to accelerated adoption of government specifications and standards. TSB rules p

    7、rovide for (a) the publication of portions of unrevised government specifications and standards without consensus voting at the SAE Committee level, (b) the use of the existing government specification or standard format, and (c) the exclusion of any qualified product list (QPL) sections.1. SCOPE:1.

    8、1 Scope:This specification covers general requirements for covers intended to protect the following aircraft parts:Cockpit Fuselage CanopyEngine ArmamentPropeller or Rotor Miscellaneous1.2 Classification :Covers shall be of the following types, as specified (see 6.2):Type I - Waterproof Fabric Mater

    9、ial (see 3.3.1.1)Type II - Coated Material (see 3.3.1.2)2. APPLICABLE DOCUMENTS:2.1 Government documents :2.1.1 Specifications and standards : The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these docum

    10、ents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2).SPECIFICATIONSFEDERALT-T-881 Twine, Cotton, SeineV-F-106 Fastener, Slide, InterlockingCCC-C-419 Cloth, Duck, Cotton, Unbleached,

    11、Plied-Yarns (Army and Numbered)CCC-D-950 Dyeing and Aftertreating Processes for Cotton ClothsPPP-B-601 Box, Wood, Cleated-PlywoodPPP-B-636 Box, Shipping FiberboardMILITARYMIL-P-116 Preservation, Methods ofMIL-W-5665 Webbing, Textile, Cotton WarpMIL-C-10799 Cloth, Coated Cotton, Vinyl Coated, Fire an

    12、d Mildew ResistantMIL-R-17343 Rope, NylonMIL-C-20696 Cloth, Coated, Polyster or Goop, Synthetic, Nylon, WaterproofMIL-F-21840 Fastener Tapes, Hook and Loop SyntheticMIL-M-46032 Fungus Resistant Treatment for Sandbags: Cooper ProcessesSTANDARDSFEDERALFED-STD-595 ColorsFED-STD-751 Stitches, Seams and

    13、StitchingSAE INTERNATIONAL AS5778 Page 2 of 17_ 2.1.1 (Continued):MILITARYMIL-STD-100 Engineering Drawing PracticesMIL-STD-129 Marking for Shipment and StorageMIL-STD-130 Identification Marking of U.S. Military PropertyMIL-STD-147 Palletized Unit LoadsMIL-STD-831 Test Reports, Preparation ofMIL-STD-

    14、2073-1 DoD Material Procedures for Development and Application of Packaging RequirementsMS20230 Grommet, Metallic, Plain and Spur, With Washer, Type I and Type IIIMS51700 Streamer, Warning(Unless otherwise indicated, copies of federal and military specifications, and standards, are available from: S

    15、tandardization Documents Order Desk Bldg. 4D, 700 Robbins Avenue Philadelphia, PA 19111-5094)2.1.2 Other Government documents, drawings, and publications : The following other Government documents, and publications form a part of this document to the extent specified herein. Unless otherwise specifi

    16、ed, the issues are those cited in the solicitation.Commercial Item DescriptionA-A-52094 Thread, Cotton(Unless otherwise indicated, copies of commercial item descriptions are available from: Standardization Documents Order Desk Bldg. 4D, 700 Robbins Avenue Philadelphia, PA 19111-5094)2.2 Non-Governme

    17、nt publication :The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of docume

    18、nts not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2).American Society for Testing and Materials (ASTM)ASTM D 3951 Standard Practice for Commercial Packaging(Application for copies of this ASTM should be addressed to American Society for Testing and Materia

    19、ls, 1916 Race Street, Philadelphia, PA 19103-1183).SAE INTERNATIONAL AS5778 Page 3 of 17_ 2.3 Order of precedence :In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes a

    20、pplicable laws and regulations unless a specific exemption has been obtained.3. REQUIREMENTS:3.1 First article:When specified (see 6.4), a sample shall be subjected to first article inspection (see 6.4) in accordance with 4.4.3.2 General :In addition to the requirements herein, the requirements spec

    21、ified on the drawings for covers for the particular model of aircraft shall also apply.3.3 Materials :Materials shall be as specified herein. Where materials are not specifically designated, they shall be designed or selected to be suitable for the purpose.3.3.1 Fabric Material :3.3.1.1 Type I:Unles

    22、s otherwise specified, Type I materials shall be as specified in 3.3.1.1.1 thru 3.3.1.1.4.3.3.1.1.1 Transparent plastic canopies : Material conforming to MIL-C-10799 shall be used in the covers for transparent plastic canopies such as the bombardier and pilot compartments, nose section, turrets and

    23、sight blisters.3.3.1.1.2 Engine covers : Material for engine covers shall conform to MIL-C-10799, type II, class 4.3.3.1.1.3 Warning streamers : Warning streamers, when specified (see 6.2), shall be in accordance with MS51700-12. The streamers shall be long enough to permit at least a 12 inch length

    24、 exposure when the cover is installed on the aircraft.3.3.1.1.4 All other covers : For covers not specified in 3.3.1.1.1 thru 3.3.1.1.3, the material shall conform to CCC-C-419, type III, 12.29 ounces per square yard. The material shall be finished in accordance with CCC-D-950, type I, class B.3.3.1

    25、.2 Type II: Unless otherwise specified (see 6.2), the material for type II covers shall conform to MIL-C-20696, type I, class 2. Warning streamers shall be the same as for type I.SAE INTERNATIONAL AS5778 Page 4 of 17_ 3.3.2 Thread: Unless otherwise specified, all thread used for sewing shall be in a

    26、ccordance withA-A-52094, ticket No. 16, 4 ply, type II, and shall be the same color as the cover material.3.3.3 Metal fittings: Grommets, eyelets, and fasteners shall conform to the applicable service use.3.3.4 Webbing (type I): Unless otherwise specified, the webbing used for attaching the covers a

    27、nd for all binding and reinforcement shall conform to MIL-W-5665, and shall be the same color as the cover material.3.3.5 Tie cord:Unless otherwise specified, the tie cord used for attaching covers and holding them in place shall be 1/4 inch rope conforming to MIL-R-17343.3.3.6 Twine:Unless otherwis

    28、e specified, the twine used for wrapping ends of the tie cords shall conform to T-T-881.3.3.7 Mildew proofing :The cotton thread, webbing, and ropes used in engine covers shall be treated in accordance with MIL-M-46032, type I organic solvent dispersion method, except the permissible weight increase

    29、 shall be 15 percent maximum and the metallic copper content shall be 0.3 0.1 percent by weight.3.3.8 Interlocking fasteners (type I) :Except as otherwise specified herein, interlocking slide fasteners shall conform to V-F-106, type IV, style No. 1 or 3, class B, size H, wire-stirrup pull, metal-zin

    30、c alloy with natural finish, color 613 of FED-STD-595. An 18 1/2 inch fabric thong shall be looped through the wire-stirrup pull and shall be capable of withstanding a tension pull of at least 100pounds.3.4 Design and construction :The covers shall be so designed that when installed they will fit ne

    31、atly and completely cover the part of the aircraft for which they are intended. The edges of the covers shall fit snugly to prevent ingress of driving rain, snow, or dust. The covers shall not contain any wrinkles or lines of stress concentration. The method of padding valleys on the edges of the co

    32、vers shall be in accordance with figure I.3.4.1 Stretch loading :The covers, when installed, shall be adjustable to and capable of withstanding a stretch loading of not less than 2 pounds per inch of width in all directions.3.4.2 Seams and stitching :The seams and stitching used in the manufacture o

    33、f covers shall be in accordance with FED-STD-751.3.4.2.1 Type I:All sewing shall be done with stitch type 301 to form a type LSc-2 seam with 3/4 inch gage. There shall be not less than four nor more than eight stitches per inch.3.4.2.2 Type II: All sewing shall be done with stitch type 401 to form a

    34、 type LSc-2 seam with 3/4 inch gage. There shall be not less than four nor more than eight stitches per inch.SAE INTERNATIONAL AS5778 Page 5 of 17_ FIGURE 1. Method of padding valleys on edge of engine and cockpit covers.3.4.3 Hems:Covers shall have a hem 1-1/2 inches wide on all free edges. Each ed

    35、ge of each hem shall have one row of stitching.3.4.4 Slits:Slits shall be provided for obstructions such as struts, stay wires, shafts, or other aircraft parts. Slits shall extend to the nearest free edge, unless another position is specified. Unless otherwise specified, the edges of each slit shall

    36、 be closed by means of an interlocking fastener installed as shown on figure 2. Means for attaching and securing covers shall be accomplished by means of ties, straps, ropes or fasteners on the edge to permit fastening them around fuselage, wings, or some adjacent fittings. The hardware or fittings

    37、used for securing the cover shall be padded and the padding permanently attached, by sewing around the periphery, to prevent contact with the aircraft skin.3.4.5 Patches:The covers shall be provided with reinforcement patches where they come in contact with sharp corners or projections.3.4.6 Engine

    38、or transmission covers : The engine or transmission cover shall extend beyond the fire wall and the propeller or rotor hub. Typical designs are shown on figures 3 through 7.SAE INTERNATIONAL AS5778 Page 6 of 17_ FIGURE 2. Cover closure.FIGURE 3. Typical cover for air-cooled-engines (3-blade propelle

    39、r)SAE INTERNATIONAL AS5778 Page 7 of 17_ FIGURE 4. Typical cover for air-cooled engine (2-blade propeller)FIGURE 5. Typical cover for liquid-cooled engines (3-blade propeller)SAE INTERNATIONAL AS5778 Page 8 of 17_ FIGURE 6. Typical cover for air-cooled engines (4-blade propeller)FIGURE 7. Typical no

    40、se cover for jet aircraft engine.SAE INTERNATIONAL AS5778 Page 9 of 17_ 3.4.6.1 Fasteners: Engine covers around the nacelles shall be closed with interlocking fasteners as specified herein. The interlocking fastener shall be offset 5 1 from the vertical centerline of the engine.3.4.6.2 Sleeves for h

    41、ot air duct : Two sleeves, each approximately 8 inches long and 13 inches in diameter, shall be attached to each engine cover to serve as a hot air duct when the free end of the sleeve is attached to a heater. One sleeve shall be so located as to coincide with the opening into the accessories compar

    42、tment of the engine. The other sleeve shall be located at the nose section of the cowling. A piece of type I lightweight webbing conforming to MIL-W-5665, approximately 52 inches long and 1/2 inch wide, shall be sewn at the midpoint to each sleeve near its open end. The color of the webbing shall ap

    43、proximately match the color of the cover.3.4.6.3 Sleeve for propeller or rotor blades : A sleeve approximately 10 inches long and of sufficient diameter to fit the propeller or rotor blade shall be attached to the engine or transmission cover for each propeller blade or rotor.3.4.6.4 Grommets:Plain

    44、grommets conforming to MS20230 shall be placed on the underside of the cover to permit excess oil drainage.3.4.7 Propeller and rotor blade covers : The propeller and rotor blade covers shall match the respective engine cover propeller sleeves or rotor head cover blade sleeves. A typical design is sh

    45、own on figure 8.FIGURE 8. Typical propeller and rotor blade coverSAE INTERNATIONAL AS5778 Page 10 of 17_ 3.4.8 Fuselage and armament covers : These covers shall be for the bombardier and pilot compartments, turrets, sight blisters, and all other gun openings.3.4.9 Miscellaneous covers : Covers for v

    46、entilation duct openings, tail and nose wheel openings, landing gear wells, and any opening too large to be covered with 2-inch masking tape shall be provided, unless justification by the weapon system manufacturer can be substantiated that covers are not required.3.4.10 Snap Fasteners (type II):Junctions between cover components, shall be secured with snap fasteners as shown on figure 9.3.4.11 Fastening tapes :Fastening tapes conforming to MIL-F-21840, type II


    注意事项

    本文(SAE AS 5778-1997 Covers Aircraft Components General Requirements for《飞机组件护盖的一般要求》.pdf)为本站会员(tireattitude366)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开