欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AS 5491C-2007 Calculation of Electron Vacancy Number in Superalloys《超耐热合金中电子空位的计算》.pdf

    • 资源ID:1024868       资源大小:246.48KB        全文页数:7页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AS 5491C-2007 Calculation of Electron Vacancy Number in Superalloys《超耐热合金中电子空位的计算》.pdf

    1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

    2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p

    3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

    4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS5491CAEROSPACESTANDARDAS5491 REV. CIssued 2000-12 Revised 2007-11 Reaffirmed 201

    5、3-10 Superseding AS5491B Calculation of Electron Vacancy Number in Superalloys RATIONALE AS5491C has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE 1.1 Purpose This SAE Aerospace Standard (AS) establishes a uniform procedure for calculation of electron vacancy numbers in su

    6、peralloys. It is intended for use by suppliers of raw materials and parts, typically castings, for which control of electron vacancy number is required by the raw material specification. 1.2 Application This procedure has been used to estimate the potential for alloy phase instability by calculation

    7、 of the density of electrons per atom in nickel-based superalloys. 1.3 Background 1.3.1 Complex, highly alloyed superalloys have been observed, for some alloy chemistries and under certain conditions, to form precipitated phases which can adversely affect strength and ductility. These phases, typica

    8、lly of a crystalline structure known as topologically close-packed, or TCP, appear after extended exposure at temperatures in the range from 1300 to 1650 F (704 to 899 C). Such phases include sigma (), mu (), or Laves. Their tendency to precipitate from the alloy matrix has been related by researche

    9、rs such as Boesch and Slaney (see 2.1) and Woodyatt, et al. (see 2.2) to the density of electrons per atom as expressed by the electron vacancy number Nv, as shown in Equation 1, as follows: g166=n1iiviv)N(mN (Eq. 1) where: Nvis the electron vacancy number for the alloy miis the atomic mass fraction

    10、 of the ith element in the alloy composition, and (Nv)iis the electron vacancy number of the ith element. Determination of the electron vacancy concentration requires an understanding of the phases which precipitate in superalloys as well as the sequence in which they form in the gamma matrix. In ge

    11、neral, this sequence is (a) the precipitation of borides, (b) the precipitation of carbides, and (c) the formation of gamma prime. When these phase reactions are considered, and adjustments made to the composition to take them into account, the residual matrix composition may be determined. From tha

    12、t residual matrix the electron vacancy number is then calculated. 1.3.2 The sequence of precipitation of strengthening phases is addressed as follows: 1.3.2.1 Nickel, chromium, titanium, and molybdenum form a boride as (Mo0.5, Ti0.15, Cr0.25, Ni0.10)3B2. 1.3.2.2 All carbon is assumed to form carbide

    13、s of the type MC and M23C6. It is assumed that MC carbides take half the carbon, reacting in sequence with tantalum, columbium, zirconium, titanium, and vanadium. The remaining carbon then reacts with chromium, molybdenum, and tungsten to form Cr21(Mo,W)2C6. 1.3.2.3 Gamma prime is formed from the re

    14、maining aluminum, titanium, hafnium, columbium, tantalum, 50 percent of the original amount of vanadium, and 3 percent of the original amount of chromium by combining with three times that total in nickel, i.e., Ni3(Al, Ti, Cb, Hf, Ta, 0.5V, 0.03Cr). 1.3.2.4 The remaining chromium content is adjuste

    15、d for that lost due to formation of borides, carbides, and gamma prime. 1.3.2.5 The remaining nickel content is adjusted for that tied up in boride and gamma prime formation. 2. REFERENCES 2.1 W. J. Boesch and J. S. Slaney: Metal Progress, July 1964, Vol. 86, No. 1, pp 109-111. 2.2 L. R. Woodyatt, C

    16、. T. Sims and H. J. Beattie, Jr.: Transactions of the Metallurgical Society of AIME, April, 1966, Volume 236, pp 519-527. 3. TECHNICAL REQUIREMENTS 3.1 Calculation of Nv3.1.1 Nvshall be calculated in the following order: 3.1.1.1 Conversion of weight percentage to atomic percentage for each element 3

    17、.1.1.2 Calculation of boron and carbide precipitation 3.1.1.3 Calculation of gamma prime precipitation 3.1.1.4 Calculation of the residual gamma matrix composition 3.1.1.5 Determination of electron vacancy number, Nv3.1.2 It may be helpful to set up a matrix similar to Table 1 to facilitate recordin

    18、g compositions through the process of electron vacancy number calculation. SAE INTERNATIONAL AS5491C Page 2 of 7_ TABLE 1 - MATRIX FOR CALCULATION OF Nv(ELECTRON VACANCY NUMBER) SAE INTERNATIONAL AS5491C Page 3 of 7_ TABLE 1 (CONTINUED) Sample Calculation based on AMS 5410: Matrix for Calculation of

    19、 Nv(Electron Vacancy Number) SAE INTERNATIONAL AS5491C Page 4 of 7_ 3.2 Conversion to Atomic Fraction 3.2.1 Enter in column A the weight percent of the individual elements by row. When the weight percent is unknown, or the element is not found in the alloy, enter zero (0). The weight percent of nick

    20、el is determined by adding the percentages of the other elements and subtracting the sum from 100. 3.2.2 Divide the weight percent of each element (the entries in column A) by their respective atomic weights (from column B) and enter this value in column C in the table. Sum the entries in column C;

    21、then individually divide the entries for each element in column C by the sum of column C. Enter this value in column D. This is the atomic fraction of that element. 3.3 Calculation of Phase Precipitations For the next series of calculations, reference will be made to cell locations in the table, suc

    22、h that D1 refers to the value of the entry in column D, row 1 (for example, the atomic fraction chromium) and E5 is the residual matrix atomic percent of cobalt, adjusted for precipitation of second phases. 3.4 Boride and Carbide Precipitation 3.4.1 Chromium Multiply D1 by 0.97 and subtract the quan

    23、tity (0.375)(D6) + (1.75)(D8), where: D1 is the atomic fraction of Cr D6 is the atomic fraction of B D8 is the atomic fraction of C Enter the result in E1. 3.4.2 Molybdenum From D3, subtract the quantity (0.75)(D6) + (0.167)(D8)(D3)/(D3+D14), where: D3 is the atomic fraction of Mo D6 is the atomic f

    24、raction of B D8 is the atomic fraction of C D14 is the atomic fraction of W Enter the result in E3. SAE INTERNATIONAL AS5491C Page 5 of 7_ 3.5 Gamma Prime Precipitation 3.5.1 Nickel Add (0.525)(D6) to D19. Subtract from that sum the following quantity: 3(D4)+(0.03)(D1) + D16 + D2 + D15 (0.5)(D8) + (

    25、0.5)(D13) + D17, where: D6 is the atomic fraction of B D19 is the atomic fraction of Ni D4 is the atomic fraction of Al D1 is the atomic fraction of Cr D16 is the atomic fraction of Cb D2 is the atomic fraction of Ti D15 is the atomic fraction of Ta D8 is the atomic fraction of C D13 is the atomic f

    26、raction of V D17 is the atomic fraction of Hf Enter the result in E19 3.5.2 Vanadium Enter (0.5)(D13) in E13, where D13 is the atomic fraction of V. 3.5.3 Tungsten From D14, subtract the quantity (0.167) (D8)(D14)/(D3+D14), where: D14 is the atomic fraction of W D8 is the atomic fraction of C D3 is

    27、the atomic fraction of Mo Enter the result in E14 3.5.4 Enter zero (0) in E2, E4, E6, E8, E15, E16, and E17. 3.5.5 Enter the value found in D5, D7, D9, D10, D11, D12, and D18 in the corresponding rows in column E. 3.6 Calculation of the Residual Matrix Composition 3.6.1 Sum the values in column E, a

    28、nd enter at the bottom of column E. 3.6.2 Column F is the matrix atomic fractions. For each row, divide the value in column E by the sum of column E calculated in 3.6.1. 3.7 Calculation of Electron Vacancy Number 3.7.1 Multiply the matrix atomic fraction in column F by the individual elemental elect

    29、ron vacancy numbers in column G, and enter the product in the corresponding row in column H. 3.7.2 The electron vacancy number for the alloy is the sum of the entries in column H, rounded to the nearest 0.01 unit. SAE INTERNATIONAL AS5491C Page 6 of 7_ 4. NOTES 4.1 The change bar ( l ) located in th

    30、e left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document. PREPARED BY AMS COMMITTEE “F” SAE INTERNATIONAL AS5491C Page 7 of 7_


    注意事项

    本文(SAE AS 5491C-2007 Calculation of Electron Vacancy Number in Superalloys《超耐热合金中电子空位的计算》.pdf)为本站会员(sofeeling205)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开