1、AEROSPACE STANDARD FITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 90 AS5162Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording
2、, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2000-07REVISED 2010-04THIRD ANGLE PROJECTION
3、CUSTODIAN: G-3/G-3B REV.BFEDERAL SUPPLY CLASS 4730 AS5162SHEET 1 OF 4REV. BPROCUREMENT SPECIFICATION: /4/ AS4875/1SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andit
4、s applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggesti
5、ons. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5162BRATIONALE OPERATING PRESSURES FOR ALUMINUM FITTINGS CLARIFIED. NADCAP-QML REQUIREMENT HAS BEEN ADDED. MATERIAL AND FINISH SPECIFICATION NUMBERS HAVE BEEN UPDATED. OTHER
6、CLARIFICATIONS AND UPDATES. FIGURE 1 FITTING, CONNECTOR, 90 INACTIVE IN PART /18/ AEROSPACE STANDARD AS5162SHEET 2 OF 4REV. BFITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 90 TABLE 1A DIMENSIONS A - F BASIC NO. AS5162/14/SIZE CODE (NOMINAL TUBE SIZE)T THREAD PERAS8879CLASS 3A A.023 C.005 D.005 E
7、F.001 04 .250 .4375-20 UNJF 1.148 .692 .474 .562 .439 05 .312 .5000-20 UNJF 1.148 .755 .536 .625 .501 06 .375 .5625-18 UNJF 1.273 .817 .599 .750 .564 08 .500 .7500-16 UNJF 1.460 1.005 .786 .937 .751 10 .625 .8750-14 UNJF 1.680 1.130 .911 1.125 .876 12 .750 1.0625-12 UNJ 2.023 1.318 1.099 1.375 1.063
8、 16 1.000 1.3125-12 UNJ 2.398 1.568 1.349 1.687 1.313 TABLE 1B DIMENSIONS G - V AND WEIGHTS BASIC NO. AS5162/14/SIZE CODE G H.010 K V LB/EAAPPROX REF ALLB/EAAPPROX REF STEELLB/EAAPPROX REF TI04 .437 .750 .375 .797- .815 .0284 .0816 .0450 05 .437 .750 .500 .797- .815 .0240 .0689 .0380 06 .500 .875 .5
9、00 .985-1.003 .0421 .121 .0667 08 .500 1.125 .750 1.173-1.191 .0668 .192 .106 10 .625 1.375 .812 1.355-1.380 .107 .307 .169 12 .625 1.625 1.000 1.668-1.693 .186 .534 .294 16 .812 2.125 1.500 2.042-2.072 .312 .896 .494 NOTICE: THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERI
10、AL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE NOTES: /1/ MATERIAL: a. DASH AS CODE LETTER - TYPE 4130 STEEL FORGING OR BAR PER AMS-S-6758 OR AMS6370; OR TYPE 4140 STEEL BAR PER AMS6382. /2/ b. CODE LETTER D - TYPE 2014-T6 ALUMINUM ALLOY FORGING PER AMS4133; OR TYPE 2024-T
11、6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6; OR TYPE 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS 4339. /2/, /18/ c. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5639. d. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5648. e. CODE LETTER R
12、 - TYPE 321 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5645. f. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY FORGING OR BAR PER AMS4928. /16/g. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS4141; OR TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9; OR TYPE 7075-T7351 ALUMINUM ALL
13、OY BAR PER AMS4124. /2/ AEROSPACE STANDARD AS5162SHEET 3 OF 4REV. BFITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 90 /2/ HEAT TREATMENT: a. DASH AS CODE LETTER - SEE HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTERS D AND W - SEE ELECTRICAL CONDUCTIVITY AND HARDNESS REQ
14、UIREMENT PER PROCUREMENT SPECIFICATION. c. OTHER MATERIAL CODE LETTERS - NONE. 3. FINISH: a. DASH AS CODE LETTER - CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2, DYE BLACK AND COAT WITH A LIGHT FILM OF OIL PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTER D: 1. ANODIZE PER AMS 2472 OR MIL-A-
15、8625, TYPE II, CLASS 2, DYE BLUE, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. 2. D CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” PLACED AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: COAT WITH HIGH PURITY ALUMINUM PER MIL-DTL-83488, CLASS 3,
16、TYPE II, WITH MAXIMUM COATING THICKNESS OF .0005. GLASS BEAD PEEN PRESSURE SHALL BE 25 psi MAXIMUM. /14/ SEE PROCUREMENT SPECIFICATION FOR ADDITIONAL REQUIREMENTS.c. MATERIAL CODE LETTERS J, K, AND R - PASSIVATE PER AMS 2700, TYPE 6 OR 7. d. MATERIAL CODE LETTER T - ANODIZE PER AMS2488 OR FLUORIDE P
17、HOSPHATE CONVERSION COAT PER AMS2486 WITH COLOR PER PROCUREMENT SPECIFICATION. e. MATERIAL CODE LETTER W: 1. ANODIZE PER AMS 2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. 2. W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CO
18、DE LETTER “V” PLACED AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: COAT WITH HIGH PURITY ALUMINUM PER MIL-DTL-83488, CLASS 3, TYPE II, WITH MAXIMUM COATING THICKNESS OF .0005. GLASS BEAD PEEN PRESSURE SHALL BE 25 psi MAXIMUM. /14/ SEE PROCUREMENT SPECIFICATION FOR ADDITIONAL REQUIREMEN
19、TS/4/ PROCUREMENT SPECIFICATION: AS4875/1 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED MANUFACTURER LIST (QML) FOR THIS PRODUCT TYPE. THE QML IS AVAILABLE AT
20、www.eAuditN./5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A3 OR 15B. a. FOR SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTER. b. FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART
21、NUMBER AND MATERIAL CODE LETTER. AEROSPACE STANDARD AS5162SHEET 4 OF 4REV. BFITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 90 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS SHOWN IN TABLE 2. TABLE 2 OPERATING PRESSURES FOR ASSOCIATED MATERIAL SIZE MA
22、TERIAL PSI 04-08 ALUMINUM ALLOY 3000 10-16 ALUMINUM ALLOY 150004-16 STEEL 3000 04-16 CORROSION RESISTANT STEEL 3000 04-16 TITANIUM ALLOY 3000 7. THIS STANDARD IS THE FUNCTIONAL EQUIVALENT OF AN776 AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD. 8. WHEN MACHINED FROM BAR OR OVERSIZED FORGIN
23、GS, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 8. 9. INTERPRETATION OF DRAWING PER ARP4296. 10. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra. 11. BREAK EDGES .003 TO
24、 .015 UNLESS OTHERWISE SPECIFIED. 12. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 13. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 0 DEGREES 30. /14/ EXAMPLE OF PART NUMBER: BASIC PART NUMBER MATERIAL CODE LETTER /1/ SIZE CODE, TUBE SIZ
25、E IN .062 INCREMENTSTHE FINISH CODE LETTER “V” WILL BE PLACED HE RE ONLY FOR MATERIA L CODE “D” AND “W” PARTS THAT ARE TO BE COATED WITH HIGH PURITY ALUMINUM /3/AS5162 D 08 V15. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS
26、, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORI
27、AL CHANGES ONLY. /16/ TITANIUM AND CADMIUM SHALL NOT BE USED FOR OXYGEN OR POTABLE WATER SYSTEMS. 17. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. /18/ INACTIVE MATERIAL CODE: a. PART NUMBERS WITH MATERIAL CODE LETTER D ARE INACTIVE FOR NEW DESIGN AS OF 2001-05. USE PART NUMBERS WITH MATERIAL CODE LETTER W FOR NEW DESIGN b. PART NUMBERS WITH MATERIAL CODE LETTER S ARE INACTIVE FOR NEW DESIGN AS OF 2009-02. USE PART NUMBERS WITH MATERIAL CODE LETTER R FOR NEW DESIGN.
