1、 AEROSPACE STANDARD FITTING, SLEEVE, FLARELESS, NONREDUCER AND REDUCER, SHORT ACORN TO WELD TUBE END AS4696Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechan
2、ical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1994-04REAFFIRMED 2
3、004-07 REVISED 2009-11THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.A FEDERAL SUPPLY CLASS 4730 AS4696 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: /4/ AS1576SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences.
4、Theuse of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.”SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcan
5、celled. SAE invites yourwritten commentsandsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4696A RATIONALE OPTIONS FOR REDUCER DESIGN AND FOR 1500 PSI AND 4000 PSI SYSTEM APPLICATION HAVE BEEN DELETED. PROCUREMENT
6、NOTE /4/ HAS BEEN CHANGED TO SPECIFY PRI-QPL-AS1576, UPDATES. FIGURE 1 - SLEEVE, TUBE END INACTIVE IN PART /16/, /17/ Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4696 SHEET 2
7、 OF 4 REV. A FITTING, SLEEVE, FLARELESS, NONREDUCER AND REDUCER, SHORT ACORN TO WELD TUBE END TABLE 1A - DIMENSIONS AND WEIGHTS, ACTIVE PARTS BASIC NO. AS4696 /17/ SIZE AND TUBE WALL CODES (RANGE OF NOMINAL TUBE WALLS FOR PORT #2) /17/ (NOMINAL TUBE SIZE) PORT #1 (NOMINAL TUBE SIZE) PORT #2 PORT #2
8、STYLE /8/ A B .010 C 0404-018 0505-022 0606-022 0808-028 1010-032 1212-043 1616-055 2020-065 .016-.018 .019-.022 .019-.022 .023-.028 .029-.032 .033-.043 .044-.055 .056-.065 .250 .312 .375 .500 .625 .750 1.000 1.250 .250 .312 .375 .500 .625 .750 1.000 1.250 B B B B B B A B .604 .602 .594 .646 .770 .8
9、02 .908 1.074 .100 .100 .100 .135 .165 .185 .250 .250 .686 .684 .676 .744 .868 .904 1.016 1.186 TABLE 1A - DIMENSIONS AND WEIGHTS, ACTIVE PARTS (CONTINUED) BASIC NO. AS4696 /17/ SIZE AND TUBE WALL CODES D /8/ E /8/ F L LB/EA APPROX REF CRES LB/EA APPROX REF TI 0404-018 0505-022 0606-022 0808-028 101
10、0-032 1212-043 1616-055 2020-065 .208 .262 .325 .438 .555 .658 .884 1.114 .176 .232 .294 .412 .498 .648 - 1.090 .050 .050 .050 .060 .060 .090 .090 .125 .371 .434 .490 .670 .786 .960 1.210 1.470 .0104 .0142 .0177 .0313 .0493 .0596 .0901 .163 .00577 .00786 .00980 .0173 .0273 .0330 .0499 .0902 TABLE 2A
11、 - DIMENSIONS AND WEIGHTS, INACTIVE PARTS BASIC NO. AS4696 /17/ SIZE AND TUBE WALL CODES (RANGE OF NOMINAL TUBE WALLS FOR PORT #2) /17/ (NOMINAL TUBE SIZE) PORT #1 (NOMINAL TUBE SIZE) PORT #2 PORT #2 STYLE /8/ A B .010 C 0604-018/15/0808-022/16/1008-022/15/1010-022/16/1010-043/16/ 1212-022/16/1616-0
12、22/16/.016-.018 .019-.022 .019-.022 .019-.022 .033-.043 .019-.022 .019-.022 .375 .500 .625 .625 .625 .750 1.000 .250 .500 .500 .625 .625 .750 1.000 A B A B B B B .594 .646 .740 .770 .770 .802 .908 .100 .135 .135 .165 .165 .185 .250 .676 .743 .838 .868 .868 .904 1.016 Copyright SAE International Prov
13、ided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4696 SHEET 3 OF 4 REV. A FITTING, SLEEVE, FLARELESS, NONREDUCER AND REDUCER, SHORT ACORN TO WELD TUBE END TABLE 2B - DIMENSIONS AND WEIGHTS, INACTIVE PARTS (CONTI
14、NUED) BASIC NO. AS4696 /17/ SIZE AND TUBE WALL CODES D /8/ E /8/ F L LB/EA APPROX REF CRES LB/EA APPROX REF TI 0604-018/15/0808-022/16/1008-022/15/1010-022/16/1010-043/16/ 1212-022/16/1616-022/16/.208 .450 .450 .575 .533 .700 .950 - .412 - .498 .498 .648 .900 .050 .060 .060 .060 .060 .090 .090 .490
15、.670 .786 .786 .786 .960 1.210 .0177 .0313 .0493 .0493 .0493 .0596 .0901 .00980 .0173 .0273 .0273 .0273 .0330 .0499 NOTES: /1/ MATERIAL: a. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS4928 b. CODE LETTER V - TYPE 15-5PH CORROSION RESISTANT STEEL BAR PER AMS5659 2. HEAT TREATMENT: a. MATERI
16、AL CODE LETTER T - NONE b. MATERIAL CODE LETTER V - HEAT TREAT TO CONDITION H1075 PER AMS2759/3 3. FINISH: ALL MATERIAL CODES - NONE. /4/ PROCUREMENT SPECIFICATION: AS1576 UNLESS OTHERWISE SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUF
17、ACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS1576 FOR THIS STANDARD. SEE http:/ FOR CURRENT QPL ONLINE. NOTE: PRI-QPL LIMITATION TO 3000 PSI REDUCER AND 1500 PSI / 4000 PSI OPTIONS PER /16/ AND /17/ OF THIS STANDARD ARE INACTIVE FOR NEW DESIGN AND CAN
18、NOT BE COVERED BY PRI-QPL-AS1576. USERS OF STANDARDS FOR THESE APPLICATIONS ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR MEANS. 5. CLEANING: MATERIAL CODE LETTER T AND V - CLEAN AND NITRIC-HYDROFLUORIC ETCH PER PROCUREMENT SPECIFICATION. 6. PACKAGING: INDIVIDUALLY PA
19、CKAGE IN CLEAN CONTAINER WITH IDENTIFICATION PER PROCUREMENT SPECIFICATION. /7/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B, MANUFACTURERS IDENTIFICATION, CAGE CODE NUMBER OR TRADEMARK, BASIC PART NUMBER, MATERIAL CODE LETTER AND TUBE WALL CODE. /8/ IF P
20、ORT #2 IS STYLE A, D WILL EXTEND THROUGHOUT THE PART AND E WILL NOT APPLY. 9. INTERPRETATION OF DRAWING PER ARP4296. 10. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. Copyright SAE International Provided by IHS
21、under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4696 SHEET 4 OF 4 REV. A FITTING, SLEEVE, FLARELESS, NONREDUCER AND REDUCER, SHORT ACORN TO WELD TUBE END 11. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 12. DIMENSI
22、ONING AND TOLERANCING: ASME Y14.5M-1994 13. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 5 DEGREES. 14. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITOR
23、IAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES
24、 ONLY. /15/ REDUCER SLEEVE SIZE AND TUBE CODE OPTION IS INACTIVE FOR NEW DESIGN. /16/ SIZE AND TUBE CODE OPTIONS FOR 1500 PSI AND 4000 PSI ARE INACTIVE FOR NEW DESIGN, THEY ARE NOT SUITABLE FOR 3000 psi SYSTEM PRESSURE AND TI-3AL-2.5V AND CRES 21-6-9 ALLOY TUBING AS LISTED IN AS18280. /17/ EXAMPLE OF PART NUMBER: Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
