1、AEROSPACE STANDARD ELBOW, 90 DEGREE, BULKHEAD, STANDARD AND REDUCER, REDUCED BODY, FLARELESS AS4132Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, ph
2、otocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1992-11REVISED 2013-08TH
3、IRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.BFEDERAL SUPPLY CLASS 4730 AS4132SHEET 1 OF 4REV. BPROCUREMENT SPECIFICATION: /4/ AS18280SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entir
4、ely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwritten
5、comments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4132BRATIONALE THE PRI-QPL NOTE AND CADMIUM WARNING NOTE HAVE BEEN REVISED. CLARIFICATIONS TO PASSIVATION NOTE AND INTENDED USE NOTE HAVE BEEN ADDED, AND
6、UPDATES MADE. FIGURE 1 ELBOW, 90 DEGREE, BULKHEAD, REDUCED BODY, FLARELESS AEROSPACE STANDARD AS4132SHEET 2 OF 4REV. BELBOW, 90 DEGREE, BULKHEAD, STANDARD AND REDUCER, REDUCED BODY, FLARELESS TABLE 1 DIMENSIONS AND WEIGHTS BASIC NO. AS4132/19/SIZE CODE HMIN J P.030 LB/EAAPPROX REF CRESLB/EAAPPROX RE
7、F TI04 .050 .390 .030 .060 .034 05 .050 .453 .159 .086 .048 06 .050 .453 .137 .090 .051 08 .050 .577 .140 .169 .097 10 .070 .702 .157 .301 .172 12 .080 .890 .166 .432 .248 16 .090 1.140 .174 .565 .325 20 .110 1.390 .071 1.262 .730 24 .130 1.640 - 1.667 .965 TABLE 2 FITTING END SIZECODE TUBE OD T THR
8、EAD PER AS8879 CLASS 3A D E 04 .250 .4375-20UNJF .371 .350 05 .313 .5000-20UNJF .371 .412 06 .375 .5625-18UNJF .379 .453 08 .500 .7500-16UNJF .461 .577 10 .625 .8750-14UNJF .511 .702 12 .750 1.0625-12UNJ .556 .890 16 1.000 1.3125-12UNJ .556 1.140 20 1.250 1.6250-12UNJ .556 1.39024 1.500 1.8750-12UNJ
9、 .556 1.640 TABLE 3 LEG LENGTH A FORGING SIZE 04 05 06 08 10 12 16 20 24 04 1.523 - - - - - - - -05 1.555 1.555 - - - - - - - 06 1.665 1.665 1.711 - - - - - -08 1.774 1.774 1.820 1.992 - - - - -10 1.914 1.914 1.960 2.132 2.273 - - - - 12 2.024 2.024 2.070 2.242 2.383 2.492 - - -16 2.149 2.149 2.195
10、2.367 2.508 2.617 2.617 - -20 2.430 2.430 2.476 2.648 2.789 2.898 2.898 2.898 - 24 2.712 2.712 2.758 2.930 3.071 3.180 3.180 3.180 3.180AEROSPACE STANDARD AS4132SHEET 3 OF 4REV. BELBOW, 90 DEGREE, BULKHEAD, STANDARD AND REDUCER, REDUCED BODY, FLARELESS TABLE 4 LEG LENGTH B FORGING SIZE 04 05 06 08 1
11、0 12 16 20 24 04 .961 - - - - - - - -05 1.055 1.055 - - - - - - - 06 1.070 1.070 1.086 - - - - - -08 1.227 1.227 1.243 1.336 - - - - -10 1.352 1.352 1.368 1.461 1.524 - - - - 12 1.414 1.414 1.430 1.523 1.586 1.649 - - -16 1.507 1.507 1.523 1.616 1.679 1.742 1.742 - -20 1.788 1.788 1.804 1.897 1.960
12、2.023 2.023 2.023 - 24 1.976 1.976 1.992 2.085 2.148 2.211 2.211 2.211 2.211NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL a. CODE LETTER J: TYPE 304 CORROSION RESISTANT S
13、TEEL PER AMS5639 b. CODE LETTER T: TYPE 6AL-4V TITANIUM ALLOY PER AMS4928 c. CODE LETTER V: TYPE 15-5PH CORROSION RESISTANT STEEL PER AMS5659 2. HEAT TREATMENT a. MATERIAL CODE LETTER J: NONE b. MATERIAL CODE LETTER T: NONE c. MATERIAL CODE LETTER V: HEAT TREAT TO CONDITION H-1075 PER AMS2759/3 /3/
14、FINISH a. MATERIAL CODE LETTER J: PASSIVATE PER AMS2700 TYPE 6 OR 7 b. MATERIAL CODE LETTER T: FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 c. MATERIAL CODE LETTER V: (1) NO SUFFIX FINISH CODE LETTER: PASSIVATE PER AMS2700 TYPE 2 OR 8 (2) SUFFIX FINISH CODE LETTER “P”; CADMIUM PLATE PER AMS-QQ-P-4
15、16, TYPE II, CLASS 2 /4/ PROCUREMENT SPECIFICATION: AS18280 UNLESS SPECIFIED OTHERWISE ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS18280 FOR TH
16、IS STANDARD. SEE HTTP:/WWW.EAUDITNET.COMFOR CURRENT QPL ONLINE. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZES 06 (.375 OD TUBE SIZE) AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS”, MATERIAL CODE LETTER AND FORGING M
17、ANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING b. FOR SIZES 08 (.500 OD TUBE SIZE) AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, MATERIAL CODE LETTER AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING AEROSPACE STANDARD AS4132SHEET 4 OF 4REV. BELBOW, 90
18、DEGREE, BULKHEAD, STANDARD AND REDUCER, REDUCED BODY, FLARELESS 6. THIS PART IS INTENDED FOR USE IN SYSTEMS WITH OPERATING PRESSURES AS FOLLOWS: a. SIZES -04 THRU -16 AT 3000 psi b. SIZES -20 AND -24 AT 1500 psi NOTE: OPERATING PRESSURES HAVE BEEN CHANGED FROM 4000 PSI AND 2000 PSI TO 3000 PSI AND 1
19、500 PSI TO COMPLY WITH AS18280 SYSTEM PRESSURE REQUIREMENTS. USERS OF THIS STANDARD FOR 4000 PSI SYSTEM APPLICATIONS ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR MEANS. /7/ FOR SHOULDER DIAMETER ON BULKHEAD REDUCERS: a. USE “S” DIAMETER (OF AS4377) FOR SMALLER BULKHE
20、AD END SIZE ON ONE STEP REDUCTIONS (E.G., 08 FORGING TO 06 BULKHEAD END, USE “S” FOR 06 BULKHEAD AS SHOULDER DIAMETER) b. USE “J” OF FORGING FOR TWO STEP OR GREATER REDUCTIONS (E.G., 08 FORGING TO 04 BULKHEAD END, USE “J” DIAMETER FOR 08 FORGING AS SHOULDER DIAMETER) 8. WHEN MACHINED FROM BAR OR OVE
21、RSIZED FORGING, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 2. /9/ RADIUS APPLICABLE TO TITANIUM PARTS ONLY. 10. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 11. THIS PART IS A REDUCED BODY VERSION OF NAS1764. /12/ SPECIFY END SIZES IN THIS ORDER: BULKHEAD END FIRST (PORT #1), REM
22、AINING END SECOND (PORT #2). 13. LARGEST END DETERMINES FORGING SIZE. /14/ APPLICABLE ONLY TO REDUCERS AND SIZE 04 AND 05 NONREDUCERS. 15. INTERPRETATION OF DRAWING PER ARP4296. 16. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES
23、TO BE 125 in Ra. 17. DIMENSIONS AND TOLERANCING: ANSI Y14.5M-1982 18. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS .5 DEGREES. /19/ EXAMPLE OF PART NUMBER: 20. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER I
24、N LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
