1、AEROSPACE STANDARD INSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 12 AS33700Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, record
2、ing, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2002-03REVISED 2010-06THIRD ANGLE PROJECTI
3、ON CUSTODIAN: SAE AE-8/AE-8C1 REV.AFEDERAL SUPPLY CLASS 5935 AS33700SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION: MIL-C-81703SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely volunt
4、ary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments a
5、ndsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS33700ARATIONALE REVISED TO PROVIDE LEGIBLE DRAWINGS NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS33700F, AMENDMENT 1, NOTICE 1, A
6、ND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS33700F, AMENDMENT 1, NOTICE 1. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATI
7、ON REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICA
8、TION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED Q
9、UALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networkin
10、g permitted without license from IHS-,-,-AEROSPACE STANDARD AS33700SHEET 2 OF 3REV. AINSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 12 THE ACTIVITY RESPONSIBLE FOR QUALIFICATION OF THESE CONNECTORS IS THE DEFENSE SUPPLY CENTER COLUMBUS, ATTN: DSCC-VQ, 3990 EAST BROAD STREET, COLUMBUS, OHIO 4321
11、3-1199. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS33700SHEET 3 OF 3REV. AINSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 12 DIMENSIONS AND MARKINGS SHOWN ARE FOR FRONT
12、FACE OF PIN INSERT (SOCKET INSERT OPPOSITE). UNLESS OTHERWISE INDICATED, DIMENSIONS ARE SYMMETRICAL ABOUT CENTERLINE. DIMENSIONS IN INCHES. ANGLES IN DEGREES. TOLERANCES: DECIMALS .005. THIS IS A DESIGN STANDARD. NOT TO BE USED AS A PART NUMBER. FOR DESIGN FEATURE PURPOSES THIS STANDARD TAKES PRECED
13、ENCE OVER PROCUREMENT DOCUMENTS REFERENCED HEREIN. REFERENCE DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATIONS FOR BID. RECEPTACLES (REF) PLUGS (REF) MS3130 MS3137 MS3132 MS3138MS3134 MS3147MS3139 MS3148 MS3140 MS3446MS3143 MS3467MS3144 MS3468 MS3145 MS3445MS3149 MS3424MS3463MS3464 MS
14、3466MS3469NOTES: 1. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION O
15、F THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
