欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE ARP 5483 1A-2012 Rolling Element Bearing No-Load Torque Test《滚动轴承的空载转矩试验》.pdf

    • 资源ID:1023095       资源大小:97.38KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE ARP 5483 1A-2012 Rolling Element Bearing No-Load Torque Test《滚动轴承的空载转矩试验》.pdf

    1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

    2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2012 SAE International All rights reserved. No part of this p

    3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

    4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/ARP5483/1A AEROSPACE RECOMMENDED PRACTICE ARP5483/1 REV. A Issued 2005-09 Revised

    5、 2012-12 Superseding ARP5483/1 Rolling Element Bearing No-Load Torque Test RATIONALE ARP5483/1A is a five-year review with only minor editorial changes. 1. SCOPE This test method outlines the recommended procedure for performing the no-load rotational starting torque test on airframe rolling bearing

    6、s. Bearings covered by this test method shall be antifriction ball bearings and spherical roller bearings. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this document to the extent specified herein. The latest issue of SAE publications shall apply. The applicable i

    7、ssue of other publications shall be the issue in effect on the date of the purchase order. In the event of conflict between the text of this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations

    8、 unless a specific exemption has been obtained. 2.1.1 ISO Publications Available from American National Standards Institute, 25 West 43rd Street, New York, NY 10036-8002, Tel: 212-642-4900, www.ansi.org. ISO 10012 Measurement management systems - Requirements for measurement processes and measuring

    9、equipment ISO/IEC 17025 General requirements for the competence of testing and calibration laboratories SAE ARP5483/1A Page 2 of 5 2.2 Definitions Starting torque is defined as the rotational force required to initiate rotation of one bearings raceway relative to the other raceway. 3. GENERAL REQUIR

    10、EMENTS 3.1 Test Apparatus 3.1.1 Torque Tester The testing device shall be capable of measuring the starting rotational torque within the bearing, without applying external radial or axial loads. The torque shall be applied either using electronically driven torque measuring device that starts from a

    11、 static state and slowly increases torque until rotation occurs or applied manually using a torque watch. The gage should be accurate to within 10% of the measured value. A simple manual testing device is shown in Figure 1. 3.1.2 (Alternative Method) In the event that the torque apparatus described

    12、in 3.1.1 is unavailable, it is permissible to use a force gage and a string (see 4.2). Torque values properly obtained from any of these methods are acceptable. 3.1.3 Calibration Calibration of the torque tester shall be in accordance with ISO/IEC 17025 or ISO 10012, and the manufacturers specificat

    13、ions. Calibration of the torque tester shall be within limits at the time of the test. 3.1.4 Bearing Adapter The bearing holding adapter shall hold the inner ring of the bearing tightly enough to turn it without causing distortion. The inner bearing ring may be held by the wedging action of a relati

    14、vely soft material, or clamping of its faces. The bearings adapter shall be directly attached to the torque tester. A simple adapter, which may be used for multiple bore sizes, is shown in Figure 1. 3.1.5 Equipment Variation Variations in the apparatus to test and hold the bearing are permissible pr

    15、oviding the procuring activity is provided with sufficient calibration data to verify the accuracy of the test conditions and results. 3.2 Test Specimen 3.2.1 Disposition of Specimen Bearings having acceptable torque levels and that remain otherwise undamaged after completion of this test are suitab

    16、le for delivery into service as this test is considered to be nondestructive. If any other test should be required, then the suitability for delivery of specimen will be based on those other tests. SAE ARP5483/1A Page 3 of 5 FIGURE 1 4. DETAILED REQUIREMENTS 4.1 Procedure for No-Load Rotational Star

    17、ting Torque 4.1.1 Rotate one of the two bearing rings at least 4 revolutions in both directions to distribute the lubricant evenly. 4.1.2 Align bearing ring faces so they are perpendicular to the bearing adapters axis and push lightly onto the adapter until wedging action just holds the bearing on t

    18、he adapter. (See 4.2 for alternative method.) 4.1.3 Apply torque either using a power driven torque measuring device which gradually increases the torque from zero until rotation starts, or manually using a torque gauge with the bearing at room temperature. A start is registered when the rotating ra

    19、ceway member starts and maintains rotation through a minimum 60 degree arc. 4.1.4 Measure the torque a minimum of three times in both rotational directions. The highest value obtained is considered the starting torque of that bearing. SAE ARP5483/1A Page 4 of 5 4.2 (Alternative technique, force gage

    20、 with string) To use this technique, fasten one end of a string to the O.D. of the bearing with tape or a similar means. Wrap the string circumferentially along the bearing O.D. for one or more complete revolutions. Attach the free end of the string to an appropriately sensitive force gage. The gage

    21、 should be accurate to within 10% of the measured value. Lightly restrain the inner ring from rotating and slowly pull on the spring scale until the outer ring starts to rotate. Measure the force (ounce or pound) to rotate the outer ring a minimum of three times in both rotational directions and rec

    22、ord the highest value. The torque is then calculated by multiplying the radius of the bearing (centerline to outside diameter) by the highest force to yield the torque (typical units: in-oz, in-lbf, or ft-lbf). 4.3 If a bearing fails to pass the specification limit, this test may be repeated twice,

    23、beginning with 4.1.1. If bearing still fails after three attempts, it must be reworked to conformance or rejected. 5. DOCUMENTATION 5.1 Test Parameters The following parameters shall be specified in the individual specification or standard: a. Failure criteria 5.2 Test Data The following information

    24、 shall be recorded in report format: 5.2.1 Bearing Description a. Part Number b. Lot Identification c. Manufacturer 5.2.2 Test Equipment a. Equipment Name, Model number, and Serial Number b. Calibration Data c. Operator d. Date tested 5.2.3 Results a. Requirements b. Measured values c. Measurement U

    25、nits 5.2.4 Failures or Problems a. Description of failure b. Corrective action taken c. Description of any malfunction resulting in an invalid or interrupted test. SAE ARP5483/1A Page 5 of 5 6. NOTES 6.1 Intended Uses This test method is intended to provide a standard method of evaluating the starti

    26、ng rotational torque of bearings without loading the bearings. 6.2 Method of Reference This test method is intended to be referenced in general and in detailed specifications, standards or drawings for airframe bearings. Specific test and data requirements are given in the applicable document. The f

    27、ollowing note shall be used to reference this test method: NOTE: The bearings shall be tested in accordance with ARP5483/1. The slash number refers to the specific test method. 6.3 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisi

    28、ons, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY SAE SUBCOMMITTEE ACBG-2, ROLLING ELEMENT COMMITTEE OF AIRFRAME CONTROL BEARINGS GROUP (ACBG)


    注意事项

    本文(SAE ARP 5483 1A-2012 Rolling Element Bearing No-Load Torque Test《滚动轴承的空载转矩试验》.pdf)为本站会员(刘芸)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开